Mitel Sx 50 Dpabx Instructions Guide

Customer Data Entrv Forms 
COMMANDS 12) - 129 
- Register 8 
I l- 11 d 
c l- d I el 
COS 1 - COS 9 PROGRAMMING 
Extension Camp-on 
0 = Disable, 1 = Enable 
-Trunk Camp-on 
0 = Disable, 1 = Enable 
- Inward Dial Trunk Camp-on 
0 = Disable, 1 = Enable 
r DID Restriction 
0 = Disable, I = Enable 
cos 1 
cos 2 
cos 3 
cos 4 
cos 5 
COS 6 
cos 7 
COS 8 
cos 9 
. 
102 2-28 
Revision 0 9104-091-l 02-NA Issue 3  

Customer Data Entry Forms 
- COMMANDS 151 - 156 TRUNK GROUP PROGRAMMING 
- Register 1 
l- - Trunk Select ( 0 = Automatic) 
- Type of Hunting 
I I I I I 
cld ef ah i  0 = Circular - 
1 = Terminal 
- Trunk Group Overflow 
0 = Disable 
1 - 6 = Trunk Group Number 
Identified Trunk Group 
0 = Disable, 1 = Enable 
r 
Trunk Group Access Code 
I ‘56 IAl I I I I I I I I 
DEFAULT VALUES 
GROUP 1 
GROUP 2 
GROUP 3 
GROUP 4 
GROUP 5 
GROUP 6 abcdefg 
I 
I ’ 
1 
1 
f 1 
1 
1 8 
9 
9104-091-l 02-NA Issue 3 
Revision 0...

Customer Data Entrv Forms 
COMMANDS 151-- 156 TRUNK GROUP PROGRAMMING 
r -Register 2 
- 
Wait for Dial Tone 
0 = No wait, outpulse after delay 
1 = Wait up to 5 seconds, then outpulse anyway 
2 = Check for dial tone every 5 seconds 
3 = Unlimited wait with detection by user 
- Dial Tone Detection Timing 
0 = 120 ms required 
1 = 40 ms required 
- Delay before Outpulsing (Wait for Dial Tone = 0) 
1 - 5 seconds 
- Answer Supervision 
0 = No Answer Supervision 
1 = Supervision is Meter Pulse or Reversal 
2...

- 
Customer Data Entry Forms 
COMMANDS 151 - 156 
TRUNK GROUP PROGRAMMING 
- Register 3 
Message Registration 
0 = Disable 1 = Enable  Message Registration 
0 = Disable 1 = Enable 
Count Additional Message Units 
0 = Disable 
1 = Enable 
2 = Enable, Insert Pseudo Message Unit every 6 seconds 
3 = Enable, insert Pseudo Message Unit every 60 seconds  Count Additional Message Units 
0 = Disable 
1 = Enable 
2 = Enable, Insert Pseudo Message Unit every 6 seconds 
3 = Enable, insert Pseudo Message Unit every...

Customer Data Entrv Forms 
COMMANDS 151 + 156 TRUNK GROUP PROGRAMMING 
r 
Register 4 
Sending Answer on Incoming Dial Trunks 
0 = Send Answer when Answer Received (Supervision is Answer only) 
1 = Send Answer after End of Dialing (Timeout) 
2 = Send Answer upon Accessing Outgoing Trunk . 
Behind’PABX Operation 
0 = Disable 
1 = Enable, Flash is Loop Disconnect 
2 = Enable, Flash is Ring Ground 
Behind PBX Recall Signal Duration 
0 = 500 ms 
1 = 750 ms 
Credit Card Calling Operation 
0 = Disable, 1 =...

Customer Data Entry Forms 
COMMAND 180 USER PROGRAMMING ACCESS 
- Register 1 
- Command 100 - System Options 
0 = Disable, 1 = Enable 
- Commands 121 - 129 COS Programming  - 
0 = Disable, 1 = Enable 
- Command 110 Feature Access Codes  - 
0 = Disable, 1 = Enable 
- Commands 301 - 310 - Station Programming 
0 = Disable 
1 = Enable all fields 
Commands 321 - 330 - Block Programming - 
Station Numbering 
Commands 331 * 350 - Block Programming - 
Station Memberships 
- Register 2 
DEFAULT VALUES 
- Commands...

Customer Data Entrv Forms 
COMMAND 180 - USER PROGRAMMING ACCESS 
- Register 3 
- Command 185 - Function Key Programming 
0 = Disable, 1 = Enable 
- Command 190 - System Security Programming 
abcdef 
3 
3’0 0 0 0 0  0 = Disable, 1 = Enable 
- Command 191 - User Security Code Programming 
0 = Disable, 1 = Enable 
- Command 193 - DISA Access Code Programming 
0 = Disable, 1 = Enable 
Note: Fields c and fare always disabled and 
r 
Command 192 - RMATS Security Code Programming 
DEFAULT cannot be modified....

Customer Data Entry Forms 
r 
TelephoneNumber 
abc def 
0 
3 
mm 
0 6 
23 9 
DD0031FO 
Figure 2-2 Programmable Function Keys 
9104-091-l 02-NA Issue 3 
Revision 0 
102 235  

Customer Data Entrv Forms 
COMI\?AND 190 SYSTEM SECURITY CODE PROGRAMMING 
-Register 1 
- System Security Code 1st Digit - 
r System Security Code 2nd Digit 
r 
System Security Code 3rd Digit 
v System Security Code 4th Digit 
a b c d e 
1 
1 7 7 7 2  I 
I I I 
COMMAND 191 
-Register 1 DEFAULT VALUES (0 - 9) 
_ 
USER SECURITY CODE PROGRAMMING 
DEFAULT VALUE.S  - User Security Code 1 st Digit 
User Security Code 2nd Digit 
User Security Code 3rd Digit 
User Security Code 4th Digit 
9104-091-l 02-NA Issue...