Mitel Sx-2000 Llightware 32, Release 1.0 Technicians Handbook

Routine Maintenance
181
Routine
Maintenance
This message appears:
FS info: File system redundancy disabled.
DBMS warning: Unable to read/write state file. Reason: Node 
does not exist.
DBMS error: Download failed. Reason: Node does not exist.
8. Enter:
VOL DISMOUNT SYSUSER
This message appears:
FS info: Dismounted volume from device DISK with name: 
SYSUSER
9. Enter:
VOL FORMAT DISK SYSUSER LOAD $8000 REDUN 
$10000 SCRATCH
If this message appears:
FS info: Continue?
Enter YES
When formatting is complete,...

Technician’s Handbook
182
16. Enter:
UPDATE APPLY  FROM 
∗.
This message appears:
Update started
Update applied successfully.
OR
If there are no updates, this message appears:
ERROR: No update files were found
The update has not been applied
Ignore this error and go to the next step.
17. Enter:
VOL DISM 
18. Remove the software RSD from the RSD drive.
19. If no update files were applied in step 16, proceed to the 
next step.
If updates were applied in step 16, hold down PANEL 
ENABLE and press the...

Routine Maintenance
183
Routine
Maintenance
4. Set all options to match those on the SX-2000 Feature 
Options Record sheet that was shipped with the software 
(X = YES).
5. Select the machine configuration FD2 and set the 
maximum number of cabinets to 12.
6. Press the  softkey, then press the  
softkey.
7. Enter the MITEL options password (from the SX-2000 
Feature Options Record sheet received with the 
software); press the  softkey, then press the 
 softkey.
This message appears:
Changes committed. **...

Technician’s Handbook
184
4. If you are loading software P02.3.2 or later, enter:
DATA RESTORE ∗.
If you are loading software earlier than P02.3.2, see Data 
Restore or Data Convert? on page 168 to determine 
which command to use in this step.
This message appears:
Existing Data Save will be deleted from Harddisk. Continue? 
(Y/N)
Enter YES
The following messages appear:
FS info: Deleting files from catalog ∗.DR.CONFIG
FS info: Deleting file ∗.DR.CONFIG.TIMESTAMP
•
•
If your software is load P02.3.2 or...

Routine Maintenance
185
Routine
Maintenance
Custom Dimensions have been detected:
Overwrite the current dimensions? (y/n)
Enter YES
This message appears:
Restart the system to enable the RESTORED dimensions. 
DATA SAVE/RESTORE/CONVERT is terminated.
6. Remove the datasave RSD from the RSD drive.
7. Hold down PANEL ENABLE and press the inactive 
plane’s RESET button.
8. Log on to the inactive plane and select maintenance 
mode.
9. Enter:
PARTITION
10. Re-insert the datasave RSD in the RSD drive.
11....

Technician’s Handbook
186
Currently restoring: Form Access Authorization
Currently restoring: Cabinet Assignment
•
•
Currently restoring: Traffic Options Assignment 
DATA RESTORE Completed.
Reminder: DBMS SAVE will save the database.
13. Enter:
VOL DISMOUNT 
14. Remove the datasave RSD from the RSD drive.
15. Enter:
TYPE ∗.DR.LOGFILE_1
Review the log for data that has not been restored. Do 
not proceed to the next step until lost data has been 
re-entered. Lost data may have to be re-entered 
manually....

Routine Maintenance
187
Routine
Maintenance
attendant consoles. 
For software loads P17.6.4 and later, enter:
LOAD CONTROLLERS
For software loads earlier than P17.6.4
–Turn power to SUPERSET 700 consoles off, then on 
again.
–Load DNI line cards. Enter:
LOAD    
20. Enter:
DATE yyyy-mmm-dd hh:mm:ss
For example: DATE 1999-sep-28 14:43:45
21. Proceed to Copy Upgraded Software to the Other Plane 
and JOIN the System on page 187.
Copy Upgraded Software to the Other Plane and JOIN 
the System
1. From the...

Technician’s Handbook
188
OR
This message may appear:
FS info: File system redundancy disabled.
DBMS warning: Unable to read/write state file. Reason: Node 
does not exist.
DBMS error: Download failed. Reason: Node does not exist.
7. Enter:
VOL DISMOUNT SYSUSER
This message appears:
FS info: Dismounted volume from device DISK with name: 
SYSUSER
8. Enter:
VOL FORMAT DISK SYSUSER LOAD $8000 REDUN 
$10000 SCRATCH
If this message appears:
FS info: Continue?
Enter YES
When formatting is complete, this...

Routine Maintenance
189
Routine
Maintenance
14. Log on to the active plane and enter:
JOIN
The inactive plane resets.
15. Wait 10 - 20 minutes, then enter FILE STAT REDUN first 
from the active plane and then from the inactive plane. 
The system should be IN SYNCH. Once the system is 
synchronized, the database is downloaded to the 
inactive plane.
16. Enter DBMS STAT first from the active plane and then 
from the inactive plane. The initialized flag should be ON.
17. Reprogram your login usernames,...

Technician’s Handbook
190
23. Perform the procedure Checking a Redundant 
System on page 158.
24. The software upgrade is complete.
Performing a Software Update on a Redundant System
Copy the Software Updates from RSD to the Inactive Plane
1. Hold down PANEL ENABLE and press ACTIVITY 
FREEZE ON.
2. Enter PARTITION first from the active plane then from 
the inactive plane.
3. Enter FIL STAT REDUN first from the active plane then 
from the inactive plane. The system should be isolated.
4. Insert the...