Mitel Sx 200 Ml Pabx Lightware 16 Instructions Guide

Reports Level Functions 
Status - Entire Bay 
To obtain an equipment status report on an entire bay, press the following softkeys: 
SHOW 
STATUS 
BAY/SLOT/CCT (enter the required bay number, press the RETURN key, and 
enter only the RETURN key for the slot, circuit, and sub-circuit prompts) 
ENTER 
Status - Specific Card Slot 
To obtain an equipment status report on a specific card slot, press the following 
softkeys: 
SHOW 
STATUS 
BAY/SLOT/CCT (enter the required bay and slot numbers, pressing the...

RS-232 Maintenance Terminal 
3:98 PM l+JRN-97 alarm status = NO RLRRM 
> 
86 SS CC SC SOFTWRRE-ID EX,TK TVPE 8G PWR MTSTRT SWSTRT HWSTRT 
0080 - - 
dsP off 
avail - - 
0100 - - 
Pcm tiff avail busy busy 
0101 - - 
PCrn off 
avail free idle 
0102 - 
P=m off avail free idle 
0103 - 
p=m off auail free idle 
010q - 
PC off avail free idle m 
0105 - 
Pcm off avail free idle 
0106 - - 
Pcm off avail free idle 
0107 - - 
Pcm off avail free idle 
DEUICE 
STflTUS 
< 
l- 
6-MT-DWR 2- 3- q- 5-CRNCEL 
7-MT-DWR-HEH...

Reports Level Functions 
Table 5-3 summarizes the terms used in the equipment status report: 
Table 5-3 Terms Used In the Equipment Status Report 
Term Meaning 
BB 
The bay in which the device is located 
ss 
The card slot in which the device is located 
cc The circuit number of the device 
SC The sub-circuit number of the device (where applicable) 
SOFTWARE-ID Type of device installed and its software identification number ( SWID ) 
EX/l-K 
The extension or trunk number of the device (where applicable);...

RS-232 Maintenance Terminal 
Table 5-3 Terms Used In the Equipment Status Report (continued) 
Term 
SWSTAT Meaning 
bsout - busied-out by maintenance - failed diagnostic test at least twice, or 
busied-out by maintenance user 
flty0 faulty with no passes 
fltyi faulty with one pass 
flty2 faulty with two passes 
flty3 faulty with three passes 
flty4 faulty with four passes 
flty5 faulty with five passes 
flty6 faulty with six passes 
The current call processing (CP) software status; for lines and trunks,...

Reports Level Functions 
Table 5-3 Terms Used In the Equipment Status Report (continued) 
Term Meaning 
HWSTA T rngbk - ringback 
rngng - ringing 
t-s232 - data station is establishing RS-232 protocol 
stowd - stowed (hard or call hold) 
suspd - suspended 
talkg -talking 
tkd - trunk dial 
wdtrx - data station waiting for dtrx response 
wfjct - waiting for call resources (receiver, channel) 
wflin - waiting for line 
The current call processing (CP) software status, for receivers 
; one of the following:...

RS-232 Maintenance Terminal 
Show Status - SWID 
This operation enables a user to show software status by selecting a device type. To 
obtain an equipment status report on a software identifier, press the following softkeys: 
SHOW 
STATUS 
SWID 
(press one of the softkeys shown in Table 5-4) 
ENTER 
The system outputs the equipment status data in the applications area of the screen. 
Where the data requires more space than is available on the screen, the user is 
prompted to request more datavia the...

Reports Level Functions 
Device Status Reports 
5.5 Device status reports display call processing information for devices (sets, stations, 
consoles, trunks, receivers, etc.) that are programmed into the system. 
A device status repot-t displays the call processing work area (CP-DWA) of a device. 
Figure 5-3 shows an example of a CP-DWA of a tie trunk. 
3:28 PH l+JRN-97 alarm status = NO RLRRM 
I 88 SS CC SC SOFTWRRE-ID EX/TK TYPE 8G PWR MTSTRT SWSTRT HWSTRT 
0060 - 
0100 - 
0101 - 
0102 - 
0103 - 
010q...

RS-232 Maintenance Terminal 
Monitor Ti Trunk Activity 
5.6 The user can monitor the activity on the ST bus to the Ti Trunk Module by displaying 
a Monitor Ti Trunk Activity report on the maintenance terminal screen. A Monitor Ti 
Trunk Activity report provides data for the DSTi, DSTo, CSTi, and CSTo buses. 
This feature also allows the user to perform the following functions: 
l Send a yellow alarm to the receiving end 
l Put the Tl Trunk card into analog loopback mode 
l Manually select the...

Reports Level Functions 
To display a Monitor Tl Trunk Activity report, press the following softkeys when in 
maintenance mode: 
REPORTS 
SHOW 
STATUS 
BAY/SLOT/CIRCUIT 
(enter PLID.....) 
LINK-STATUS (This softkey only appears if the affected circuit is a Ti circuit) 
TRUNK-NUM 
Enter the circuit location on the Ti Trunk Card (24 Tl circuits per Ti Trunk Card) 
ENTER 
Data from the DSTi, DSTo, CSTi, and CSTo buses of the selected trunk is presented 
on the screen. 
To send test data, press the following...

RS-232 Maintenance Terminal 
Table 5-5 provides definitions for the softkey commands that you can enter from the 
maintenance terminal to test the Ti link. 
Table 5-5 Softkey Definitions 
Softkey 
TRUNK-NUM 
CANCEL 
YELLOW 
RETURN 
MANUAL 
AUTO 
SEND 
TxPadz 
RxPad 
Tx/AB-00 
Tx/AB-01 
Tx/AB-10 
Tx/AB-11 
LOOPBACK - 
INTERNAL 
LOOPBACK - 
EXTERNAL 
LOOPBACK-D 
UPDATE Definition 
Prompts for target trunk. Defaults to 01. Valid is 01-24, 
Goes back to REPORTS LEVEL form. The default settings for ail...