Mitel Sx 200 Ml Pabx Lightware 16 Instructions Guide

Camp-On: Allows an extension to notify a busy extension (via a beep) that they desire 
communication. The camped-on call rings when the called party goes on-hook. 
Can Flash If Talking To An Incoming Trunk: Allows an extension to flash the switch- 
hook when connected to an incoming trunk. 
Can Flash If Talking To An Outgoing Trunk: Allows an extension to flash the switch- 
hook when connected to an outgoing trunk. 
Cannot Dial a Trunk After Flashing: Prevents an extension from accessing a trunk 
after...

Customer Data Entry 
DID Trunk to DID Trunk Connect: Allows an extension to connect 2 DID trunks 
together. 
Direct To ARS: Allows an extension to be routed directly to ARS upon going off-hook. 
The system automatically dials the ARS leading digit string. 
Directed Call Pickup: Allows the extension to dial the Directed Call Pickup access 
code, and answer a call ringing at another extension. 
DISA During Night Service Only: Allows for a trunk to be a DISA trunk only when the 
system (or tenant group) is...

Extension Non-CO Trunk to Trunk Connect: Allows an extension to connect any 
non-CO type trunk to any other trunk. 
Flash Disable: Prevents an extension from using any feature that required the use of 
the switchhook flash. 
Flash For Waiting Call: Allows a user to place a call (2-party or multi-party) on con- 
sultation hold and connect to a waiting call, via a flash of the switchhook. 
Flash For Attendant: Allows an extension to ring the attendant immediately upon 
flashing the switchhook. 
Flash-In...

Customer Data Entry 
4-24 Key System - Direct Paging Handsfree Answerback: Allows a SUPERSET 470, 
SUPERSET 420 or a SUPERSET 430 key system set user to access the handsfree 
answerback feature for directed page calls. 
Key System - Direct CO Access: Allows a key set to directly access a CO trunk using 
Feature Access Code 50. 
Limited Wait For Dial Tone: Instructs a trunk to wait a pre-determined period for dial 
tone from the far end before sending digits. This option must be enabled for ISDN 
trunks....

Originate Only: Prevents an extension from receiving any calls, unless they are for- 
warded. 
Outgoing Trunk Callback: Allows Callback - Busy on outgoing trunks. 
Outgoing Trunk Camp-On: Allows Camp-On on outgoing trunks. 
Override: Allows an extension to override (intrude into the conversation of) a busy 
extension. 
Override Security: Prevents other extensions from overriding calls. 
Paging Default: Sets the default paging zone for the station. 0 enables all zones. 
Paging Zone Access: Allows an...

Customer Data Entry 
SMDR - Record ANl/DNlS/CLASS: Allows ANVDNIS information to be reported in 
the SMDR trunk record. 
SMDR - Record Incoming Calls: Causes incoming trunk calls to be recorded by 
SMDR. 
SMDR - Record Meter Pulses: Allows meter pulses received from the Central Office 
to be counted. and recorded. 
Special DISA: Allows for DISA users to enter verified account codes rather than the 
DISA access code. (Feature Access Code 19). 
Standard Ring Applies: When enabled for trunks, this option...

SWE/?SETTelephone - Message Program: Allows changing/programming of advi- 
sory messages from the set. 
SUPERSE~Telephone - Night Service Switching: Allows a SWERSET 43U or 
SUPERSETd20telephone to change the night service status of the system or a tenant 
group. 
SUE/?SE~Telephone - Room Status Display: Allows a SUPERSET 430 or 
SUPERSET420telephone to check room status. This feature is part of the Hotel/Motel 
feature package. 
TAFAS Access During Day Service: Allows the extension to answer incoming...

Customer Data Entry 
Form 04 - System Options/System Timers 
4.4 This form specifies the system’s options and timers that are system wide. See 
Table 4-3 for the complete list of options and timers, and Figure 4-4 for the 
form layout (the example used shows “BOTTOM” of the form where the new function- 
ality is located). 
3127 PM 9-JfiN-97 
System 
Options (Displaying ENfiBLED Options) 
> 
Class Receiuers in Spine Bay #t6 (0..6) 
Class Receiuers in Spine Bay #7 (0..6) 
Mite1 Options Password 
System...

, VARIABLE: This softkey appears only when System Option 55 is selected (displayed 
on the command line). Pressing the VARIABLE softkey sets the status of System 
Option 55 to Variable; the STATUS field shows the VARIABLE prompt. The selection 
is completed by pressing the ENTER softkey. Account Codes entered into Form 33, 
Account Code Entry, can be from 1 to 12 digits in length. 
INTERNAL: This softkey appears only when System Options 57 and 58 are selected 
(displayed on the command line). Pressing...

Customer Data Entry 
Table 4-3 System Options and Timers 
Option Numbers For 
LIGHTWARE 16 ML 
01 
02 
03 
04 
05 System Options / System Timers 
24 Hour Clock 
Message Lamp Test Enable 
Single Paging Amplifier 
Message Waiting and Message Register Clear Print 
Verified Account Codes 
06 Analogue Networking SMDR 
07 Cancel 24-Hour Message Waiting 
08 Five-Digit SMDR 
09 Attendant Call Block 
10 Attendant Conference Beeps 
II Automatic Wake-up 
31 Satellite PBX 
32 Outgoing Call Restriction 
33 Room...