Mitel SX-200 DIGITAL Pabx General Description Manual

Features Description 
4.24 DEFAULT CUSTOMER DATA 
Description 
The system is preprogrammed with default, Class-Of-Service Options, 
and Class-Of-Restriction Options; if no alternates are programmed, the 
system will default to the preprogrammed data. The Feature Access 
Codes can be entered in Customer Data Entry (CDE). 
Conditions 
Refer to Section MITL9108-093-270-NA, Customer Data Entry (CDE) for 
additional information. 
Programming 
None 
Operation 
None 
Page 4-25  

Features Description 
4.25 DEVICE lNTERCONNECTION 
Description 
This feature provides a means of disallowing connection between 
device tvpes. This is intended to provide a method of meeting inter- 
connection regulations imposed by various countries. 
Conditions 
0 The device interconnection rules imposed by the device inter- 
connection table may be overridden by the trunk connect COS 
options (see ‘Trunk Connect’). 
Programming 
Set the interconnection rules as required, using the ALLOW/DISALLOW...

Features Description 
4.26 DIAL ACCESS TO THE ATTENDANT 
Description 
An extension may access the Attendant by dialing a code (usually 0). 
Conditions 
The Attendant Access Code may not conflict with any other access 
code. 
Programming 
Assign an access code to Feature 11 (Extension General Attendant 
Access). 
Operation 
To dial the attendant: 
a Dial Attendant Access Code. 
e 
Ringback tone returned. 
m 
Attendant Console rung. 
Page 4-27  

Features Description 
4.27 DICTATION TRUNKS 
Description 
This system option provides for any rotary dial digits to be transmitted 
out on a trunk at any time during a call. 
Conditions 
Dictation trunks that require tone-to-pulse conversion must have the 
“Dictation Trunk” trunk descriptor option enabled. Note that doing so 
will cause a DTMF receiver circuit to be used for the duration of the 
call. This is also true for trunks that require pulse-to-pulse conversion. 
If the dictation trunk can receive...

Features Description 
4.28 DIGIT TRANSLATIDN 
Description 
The SX-200@ DIGITAL PABX may be programmed to provide one of 
four Digit Translation Plans for rotary telephone sets. 
Digit Translation Plan 0 provides the following translations: 
The digit 1 produces 1 pulse. 
The digit 2 produces 2 pulses. 
The digit 3 produces 3 pulses. 
The digit 4 produces 4 pulses. 
The digit 5 produces 5 pulses. 
The digit 6 produces 6 pulses. 
The digit 7 produces 7 pulses. 
The digit 8 produces 8 pulses. 
The digit 9...

Features Description 
The digit 7 produces 4 pulses. 
The digit 8 produces 3 pulses. 
The digit 9 produces 2 pulses. 
The digit 0 produces 1 pulse. 
Conditions 
Only one translation plan may be in effect at a time. 
Programming 
Select the desired translation plan via System Option 35 (Digit Transla- 
tion Plan O-3). 
Bperatiom 
None 
Page 4-3Q  

Features Description 
4.29 DIRECT INWARD DIAL (DID) TRUNK SUPPORT 
Description 
This feature allows DID Trunks to be used in the SX-200@ DIGITAL 
PABX. DID trunks allow incoming trunk calls (DID) to reach extensions 
directly, without Attendant intervention or assistance. The length of the 
incoming number, the number of digits to be absorbed, and a prefix 
digit, if required, may also be specified. 
Conditions 
If the DID trunk sends less digits than expected, the trunk will receive 
reorder tone from...

Features Description 
Operation 
None 
Page 4-32  

Features Description 
4.30 DID INTERCEPT TO RECORDED ANNOUNCEMENT 
Description 
incoming DID trunk calls can be intercepted to groups of recording 
devices after dialing vacant numbers, reaching busy extensions, ob- 
taining no answer, etc. 
Conditions 
m 
e 
Programming 
l 
ONS ports, to which the recording devices are connected must 
be defined in CDE before being entered into a recording group. 
This feature is not available in software Generic 1000. 
Enter the extension numbers of the ONS ports to...

Features Description 
4.31 DIRECT-IN LINES (DIL) 
Description 
This feature allows CO trunks to reach specific answering points - 
Attendant supervision is not required. Incoming calls from the trunk 
ring the answering point directly - they need not appear at the Atten- 
dant Console. An answering point may be one of the following: 
- an extension number 
- a hunt group access code 
- an Attendant console LDN position access code 
- a night bell access code. 
If the assigned answering point is busy when...