Minolta Di450 User Manual

2-18
Getting to Know Your Machine
Chapter 2
6. Turning ON and OFF and Initial Mode
Tu r n i n g O N a n d O F F
When Machine is Turned ON
When the Power Switch is turned ON, the Start key lights up orange.
In about a few seconds, the message “Now warming-up. Ready to scan.” appears and the Start key lights
up green. The machine thereafter enables its auto copy start function.p. 2-19
At this time, however, pressing the Start key does not start a copy cycle. The machine needs a warm-up
period of about 4...

2-19
Getting to Know Your Machine
Chapter 2
7. Auxiliary Functions
Auxiliary Functions
The Panel Reset key resets all control panel
settings to default settings including the number of
copies and zoom ratio. The settings just made
would also be cleared.
Useful Tips
 The Panel Reset key enables you to cancel all
previous settings at the touch of the key.
 To avoid miscopy, try to press this key before
making any setting for your own copy job.
If no key on the control panel is pressed within 1
min. after...

2-20
7. Auxiliary Functions
Getting to Know Your Machine
Chapter 2
The Interrupt function allows you to interrupt a
current job and run a different one. Pressing the
Interrupt key once sets the machine into the
Interrupt mode.
Pressing the Interrupt key again lets the machine
leave the Interrupt mode, returning to the previous
settings.
NOTES
 To cancel an Interrupt cycle, you need to press
the Interrupt key.
 Neither the Panel Reset key nor Auto Panel
Reset function is effective for canceling an...

3-1
Making Copies
Chapter 3
Chapter 3
Making Copies
Downloaded From ManualsPrinter.com Manuals 

3-2
Making Copies
Chapter 3
1. Using Basic Copying Functions
Basic Copying Procedures
One of the most basic copying jobs is to make full-size (×1.000) copies of the original.
Place the original in position (step 2), set the number of copies to be made (step 9), and press the start key
(step 10). This will allow you to make full-size copies on paper of the same size as the original.
[*In the initial mode, Auto Paper, Full Size, and Auto Exposure are automatically selected.]
The selections you make on the...

3-3
1. Using Basic Copying Functions
Making Copies
Chapter 3
Useful Tip
Different functions can be combined in various ways to create different types of copy. See “Typical
Function Combinations” that schematically shows different types of copy produced by combining
different functions.
p.4-17. Touch [Density].
p.3-44
4003P003CA
4003P004CA
Selecting the auxiliary functions  Changing the exposure level
Selecting the exposure level.
 Making a file margin on the copy
 Using OHP Interleaving
8. Touch...

3-4
Making Copies
Chapter 3
2. Placing the Original
Using the Electronic Document Handler

The Electronic Document Handler automatically feeds in sheet originals placed on the Document
Handling Tray one by one. After the copy cycle has been completed, it automatically ejects the original
onto the Document Exit Tray.
Types of Originals: Sheets (Plain paper)
 1-sided Original (weighing 13-1/4 to 29-1/4 lb)
 2-sided Original (weighing 16 to 24 lb)
 Mixed Original Detection mode (weighing 16 to 24 lb)...

3-5
2. Placing the Original
Making Copies
Chapter 3
Slide the Document Guide Plate to the size of
the originals.
Load a neat stack of originals face up on the
Document Handling Tray.NOTES
 The maximum number of originals that can be
loaded: Up to 100.
 The machine is capable of scanning a document
consisting of 100 or more pages at one time.

p.3-67
 Make sure that the top level of the original
stack does not exceed the
marking.
 Make sure that the Document Guide Plate is in
touch with the edges of...

3-6
2. Placing the Original
Making Copies
Chapter 3
Using the Original Glass
Different methods are used to place the original depending on its type. Use the procedure appropriate for
your original. If you are using an Electronic Document Handler,

p. 3-4
 If you place your original directly on the Original Glass, make sure that it is placed in the direction
illustrated below.
 If you need to place your original in a direction different from these examples, set “Original Direction”
(the direction of the...

3-7
2. Placing the Original
Making Copies
Chapter 3

Place the open book so that its top edge is at
the rear of the machine and the center of the
book is aligned with the Book Marker
indicated on the Original Length Scale.
Gently lower the Original Cover.
NOTES
 If the original is thick, make a copy with the
Original Cover raised open.
 Not positioning the open book properly will
result in copies with pages in incorrect order.
 Do not look directly at the Original Glass
surface as a strong beam of...