MikroTik Router OS V3.0 User Manual

•mii-type1- uses Media Independent Interface type1 to determine link status. Link status
determenation relies on the device driver. If bonding shows that the link status is up, when it
should not be, then it means that this card dont support this possibility.
•mii-type2- uses MII type2 to determine link status (used if mii-type1 is not supported by the
NIC)
•none- no method for link monitoring is used. If a link fails, it is not considered as down (but no
traffic passes through it, thus)....

		

 &J  

  
  	 	
Application Examples
Bonding two Eoip tunnels
+  
 
 
 
  
  
 
 

 
   	( 

 
 - *!$  	 E 	

 
 
  


   	
 ( 	(
6 	 	
 
	
 



 
 *



 
 
 *!$ 	 
  
 

•3
	

 
 

•
 /interface printFlags: X - disabled, D - dynamic, R - running# NAME TYPE MTU0...

• interface eoip add remote-address=10.1.0.112 tunnel-id=2\... mac-address=FE:FD:00:00:00:04[admin@office1] > interface eoip printFlags: X - disabled, R - running0 R name=eoip-tunnel2 mtu=1500 mac-address==FE:FD:00:00:00:04 arp=enabled\... remote-address=10.1.0.112 tunnel-id=2
• interface eoip add remote-address=10.1.0.111 tunnel-id=2\... mac-address=FE:FD:00:00:00:02[admin@office2] > interface eoip printFlags: X - disabled, R - running0 R name=eoip-tunnel2 mtu=1500 mac-address=FE:FD:00:00:00:02...

• add slaves=eoip-tunnel1,eoip-tunnel2[admin@office2] interface bonding> printFlags: X - disabled, R - running0 R name=bonding1 mtu=1500 mac-address=00:0C:42:03:20:E7 arp=enabledslaves=eoip-tunnel1,eoip-tunnel2 mode=balance-rr primary=nonelink-monitoring=none arp-interval=00:00:00.100 arp-ip-targets=mii-interval=00:00:00.100 down-delay=00:00:00 up-delay=00:00:00lacp-rate=30secs[admin@office2] ip address> add address=3.3.3.2/24 interface=bonding1[admin@office2] ip address> printFlags: X - disabled, I -...

CISCO/Aironet 2.4GHz 11Mbps Wireless Interface
Document revision 1.3 (February 6, 2008, 2:56 GMT)
This document applies to MikroTik RouterOS V3.0
Table of Contents
TableofContents
Summary
Specifications
AdditionalDocuments
WirelessInterfaceConfiguration
Description
PropertyDescription
Example
Example
Troubleshooting
Description
ApplicationExamples
Point-to-MultipointWirelessLAN
Point-to-PointWirelessLAN
General Information
Summary
  
 ! 
 
 
 3*!3 1+

 -DI,2 6...

I 	
 
	 
 	
	 
 $5# 	

•N/.7..:G:C	. $3*1*!+ DC.. 	
 D

ap1(MAC address) - forces association to the specified access point
ap2(MAC address) - forces association to the specified access point
ap3(MAC address) - forces association to the specified access point
ap4(MAC address) - forces association to the specified access point
arp(disabled|enabled|proxy-arp|reply-only; default:enabled) - Address Resolution Protocol
beacon-period(integer: 20..976; default:100) - Specifies beaconing period (applicable to ad-hoc
mode only)
card-type(read-only: text) - your...

a user to use a client adapter around the world while still maintaining regulatory compliance
Example
*

	 
	

	 



[admin@MikroTik] > interface printFlags: X - disabled, D - dynamic, R - running# NAME TYPE MTU0 R ether1 ether 15001 X ether2 ether 15002 X pc1 pc 1500[admin@MikroTik] interface> set 2 name aironet[admin@MikroTik] interface> enable aironet[admin@MikroTik] > interface printFlags: X - disabled, D - dynamic, R - running# NAME TYPE MTU0 R ether1 ether 15001 X ether2 ether...

Description
L 
 
 
	
 

 	 
	

  *1  	 	 	
 *@ 	  
 	
	

	 *
  
 
	
   	
 *@ 

  
  
 	
 

 
 
 
 	

	
	 *1  	 	 


 + 
 	 
 ( 
 *@ < 	
 *1  .:..  ./C.   


 	
•#  
 
    
  
  
  :
 43;%
 
 
 

 *@ 
 
 5*$ 

•#  :
 4<   
     ...

 	 

  


 
 
  

% ,0) 	
 	 *$ 	  
 

 /.//.1-D
 
 
	

 8  
 +$ 
1.!


 
 !( !
 *

 & 
 :- 		
 		
 *
  	    H
H
2.!


 
 	 	
	 	
 	
 /7// 	
 
 	 	
 	
 /
3.3
 
 8
 
  	   -DD-,2
4.&# 3*!3 1+

 ) 
 !
 3
	

1	1F

1)1J	K

 * 
	( 
 
 %K...