MikroTik Router OS V3.0 User Manual

0x1000-0x10FF [National Semiconductor Corporation DP83815 (MacPhyter) Et...0x1000-0x10FF ether10x1400-0x14FF [National Semiconductor Corporation DP83815 (MacPhyter) Et...0x1400-0x14FF ether20x1800-0x18FF [PCI device 100b:0511 (National Semiconductor Corporation)]0x1C00-0x1C3F [PCI device 100b:0510 (National Semiconductor Corporation)]0x1C40-0x1C7F [PCI device 100b:0510 (National Semiconductor Corporation)]0x1C80-0x1CBF [PCI device 100b:0515 (National Semiconductor Corporation)]0x1CC0-0x1CCF [National...

	 	( 
 	
  
 

 

	 	
Notes on PCMCIA Adapters
Description
3

 
 
 
 $33*+7*!+ 	
 $33*+7$3* 		
 	 

 
  
 

 !
•*3 , $33*+7$3* ) 
 

Ethernet Interfaces
Document revision 1.4 (September 10, 2007, 11:48 GMT)
This document applies to MikroTik RouterOS V3.0
Table of Contents
TableofContents
GeneralInformation
Summary
Specifications
AdditionalDocuments
EthernetInterfaceConfiguration
PropertyDescription
CommandDescription
Notes
Example
MonitoringtheInterfaceStatus
PropertyDescription
Notes
Example
Troubleshooting
Description
General Information
Summary
 
 ! 
 (	 
  F


 *

	  
 
 ...

Property Description
arp(disabled|enabled|proxy-arp|reply-only; default:enabled) - Address Resolution Protocol
auto-negotiation(yes|no; default:yes) - when enabled, the interface advertises its maximum
capabilities to achieve the best connection possible
cable-setting(default|short|standard; default:default) - changes the cable length setting (only
applicable to NS DP83815/6 cards)
•default- suport long cables
•short- support short cables
•standard- same as default
disable-running-check(yes|no;...

Flags: X - disabled, R - running# NAME MTU MAC-ADDRESS ARP0 R ether1 1500 00:0C:42:03:00:F2 enabled[admin@MikroTik] interface ethernet> print detailFlags: X - disabled, R - running0 R name=ether1 mtu=1500 mac-address=00:0C:42:03:00:F2 arp=enableddisable-running-check=no auto-negotiation=yes full-duplex=yescable-settings=default mdix-enable=yes speed=100Mbps[admin@MikroTik] interface ethernet>
Monitoring the Interface Status
Command name:/interface ethernet monitor
Property Description...

•4
	 

  $ $ 
	

*
  ( 	 	 
   
	
 
 ( (  

  
 
	

 
 
 

 	
 
 9*3% 	
 &    	  

 

Page 75 of 480Copyright 1999-2007, MikroTik. All rights reserved. Mikrotik, RouterOS and RouterBOARD are trademarks of Mikrotikls SIA.Other trademarks and registred trademarks mentioned herein are properties of their respective owners. 

FarSync X.21 Interface
Document revision 1.2 (February 6, 2008, 2:56 GMT)
This document applies to MikroTik RouterOS V3.0
Table of Contents
TableofContents
GeneralInformation
Summary
Specifications
AdditionalDocuments
SynchronousInterfaceConfiguration
Description
PropertyDescription
Example
Troubleshooting
Description
SynchronousLinkApplications
MikroTikroutertoMikroTikrouter
MikroTikroutertoMikroTikrouterP2PusingX.21line
MikroTikroutertoCiscorouterusingX.21line...

E 	
 	
 
 

	 
	 
 	  
( 
 
 

	
  
	 



	  
	

Property Description
clock-rate(integer; default:64000) - the speed of internal clock
clock-source(external|internal; default:external) - clock source
disabled(yes|no; default:yes) - shows whether the interface is disabled
frame-relay-dce(yes|no; default:no) - operate in Data Communications Equipment mode
frame-relay-lmi-type(ansi|ccitt; default:ansi) - Frame Relay Local...

Synchronous Link Applications
MikroTik router to MikroTik router
A
  
 
 
 

 
 
 
  
 


 
 	 	 
 

		
 
 

	   
	 	
 
 
 



 (
 	( 45 	
 


 

 

	   	 
[admin@MikroTik] ip address> add address=1.1.1.1/32 interface=farsync1 \\... network=1.1.1.2 broadcast=255.255.255.255[admin@MikroTik] ip address> printFlags: X - disabled, I...

9
 
	
  
 

7
7

 
 
 

 	  
 
 :- 
 
 	


$ 
 
 

45  
 
 
 	
 
 		
 	  
 
 -