Miele G 7881 Service Manual

2.8.21 E 21, Program-Dependent Activation of 10th Wash Block NS1 (Final Rinse 1)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 21
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock10Flashing display, wash block 10 NS1 (final rinse 1) not
active
10
–Constant display, dash at top: wash block 10 NS1 (final
rinse 1) activated with KW (cold water)
10–Constant display, dash in middle: wash block 10 NS1 (final
rinse 1) activated...

Program Level E 23
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock e.g., 10Setting the holding time t5 in temperature step T5 in 1-min
steps, between 1 min and 15 min
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock...

Program Level E 25
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 34:Program LevelE 25
2.8.26 E 26, Program-Dependent Setting of Temperature Holding Time t2 in Wash
Block NS2 (Final Rinse 2)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 26
Program Selector...

For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 28
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
1 o'clock e.g., 55Temperature setting in 1°C steps between 30°C and
99°C
2 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 2 o'clock setting
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can...

Program Level E 30
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
3 o'clockAs described for the 1 o'clock setting, but only applicable for the cleaning
program that can be started at the 3 o'clock setting
etc. . . . . . .
Table 39:Program LevelE 30
2.8.31 E 31, Program-Dependent Temperature Setting for Drying TA2
G 7882 CD, G 7883 CD
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 31
Program Selector
Switch SettingDisplay...

2.8.33 E 33, Resetting Electronic
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 33
Program Selector
Switch SettingDisplay Function (Depending on Cleaning Program)
Immaterial00Unprogrammed electronic - Cannot be modified
PPWith programmed electronic - Can be reset to00or back to
PP
Table 42:Program LevelE 33
2.8.34 E 34, Clock Setting (From P 06)
For programming mode access, see Programming Mode Summary, 070 4.1.
x
Program Level E 34
Program Selector Switch...

Service Level S 21
Program Selector
Switch SettingDisplay Function
4 o'clock
4)
40Serial printer interface not available
41Serial printer interface activated
42Serial printer interface activated and test
printout. In order to receive a printout
immediately after entry, press theStart
button twice (save).
5 o'clockCoarse filter operating
hours
2)in h (e.g., 250)—
6 o'clockFine filter operating hours
2)in
h (e.g., 500)—
7 o'clockCoarse filter operating hours
with reset
3)(e.g., 010)—
8...

Service Level S 22
Program Selector
Switch SettingDisplay Function
6 o'clock e.g., 11Hour setting (01 - 23)
7 o'clock e.g., 45Minute setting (01 - 59)
8 o'clock e.g., 108Capacity - DOS dispenser pump 1, range 10 - 150 mL/min
9 o'clock—DOS dispenser pump 2 is rinse aid door dispenser, no
capacity setting
10 o'clock e.g., 18Capacity - DOS dispenser pump 3, range 10 - 150 mL/min
11 o'clock e.g., 110Capacity - DOS dispenser pump 4, range 10 - 150 mL/min
Table 45:Service LevelS 22...

2.9.4 S 24, Checking Outputs 12 - 19
For service mode 2 access, see Service Mode 2 Summary, 070 4.3.
x
Service Level S 24
Program
Selector Switch
SettingDisplay Function
1 o'clock—Vacant
2 o'clock 12
1)Output 12: DOS 4 dispenser, disinfectant
3 o'clock 13
1)Output 13: DOS 3 dispenser, neutralizing agent
4 o'clock 14
2)Output 14: Drying unit base load
5 o'clock 15
2)Output 15: Drying unit control
6 o'clock 16
2)Output 16: Drying unit fan
7 o'clock 17
2)Output 17: DK3), no...

Service Level S 25
Program
Selector Switch
SettingDisplay Function
11 o'clock00 Machine number deleted
PP Machine number programmed
Table 48:Service LevelS 25
Note
The set machine number is recorded in a printout via the serial interface.
2.9.6 S 26, Special Functions
For service mode 2 access, see Service Mode 2 Summary, 070 4.3.
From P 05: Program interruption possible.
From P 05: Display for machines without steam condenser (DHK), display only for
machines with pulsed heating.
Dispensing relay...