Miele G 7881 Service Manual

2.5.3 General Information - Service Mode 1
Service mode 1 can be used to advance through the individual program steps of a
selected program. Steps should be advanced rapidly with a maximum of 2
seconds of pause. If a step is not advanced, the selected program is continued
normally from the step reached. The parameters affecting the fault-monitoring
system also apply during the service mode. If, e.g., a heating step is accessed,
then a fault is registered if sufficient water has not previously entered the...

printer interface is present and activated. When stepping back and forth through
the various programming levels the active programming level is onlydisplayed,
e.g.,S 23, when the program selector switch is turned to the 12 o'clock setting.
Settings in service mode 2 always apply for all cleaning programs, except when
impermissible settings have been made in individual cleaning programs. Service
mode 2 can be quit without saving any parameter changes that may have been
made by interrupting the power...

x
Program
BlockG 7882 Wash Programs1)
CHEM 60°C-5 mincombi CHEM
60°C-5 minA (customisable) vario TD NR UNIVERSAL
VR 1— — —10 L cold water 10 L cold water
1 min 1 min
60 s drainage 60 s drainage
VR 2[10 L cold water] [10 L cold water]
— — — [1 min] [1 min]
[60 s drainage] [60 s drainage]
HR 1[10.5 L cold water] [10.5 L cold water]
— —10.5 L cold water
[DOS 1 / 40°C] [DOS 1 / 40°C]DOS 1 / 40°C
[60°C / 3 min] [55°C / 3 min]60°C / 3 min
[60 s drainage] [—]60 s drainage
HR 2[—] [—]—10.5 L cold water
— DOS 1 /...

Program Block G 7883 Wash Programs1)
SPECIAL 93°C-10 min vario TD Customer Anorganica
VR 1[—][10 L cold water]10 L cold water
— [1 min]1 min
[60 s drainage]60 s drainage
VR 2[—]— —10 L cold water
DOS 3 immediately
50°C / 1 min
60 s drainage
HR 1[10.5 L cold water]10.5 L cold water
— — [DOS 1 / 40°C]DOS 1 / 40°C
[[93°C / 10 min]]55°C / 5 min
[60 s drainage]60 s drainage
HR 2[—]—10.5 L hot water 10.5 L hot water
DOS 1 / 40°C DOS 1 / 40°C
80°C / 3 min 75°C / 3 min
60 s drainage 60 s drainage
CH-DESIN[—]...

Program
BlockG 7883 Wash Programs1)
Organica Standard Universal Intensive Plastic
HR 210.5 L hot water[10.5 L hot water] [10.5 L hot water]10.5 L hot water 10.5 L hot water
DOS 1 / 40°C[DOS 1 / 40°C] [DOS 1 / 40°C]DOS 1 / 40°C DOS 1 / 40°C
85°C / 3 min[75°C / 3 min] [80°C / 3 min]85°C / 3 min 55°C / 5 min
60 s drainage[60 s drainage] [60 s drainage]60 s drainage 60 s drainage
CH-DESIN—[—] [—] [—] [—]
SP 1— — — — —
SP 29 L hot water 9 L hot water 9 L hot water 9 L hot water 9 L hot water
DOS 3 immediately...

2.7 Software Index Versions, Program Sequence Plans
2.7.1 List of Software Index Versions and Modifications
–Software index P 00 (start of pilot series)
–Software index P 01 (ID 488)
–Software index P 02 (ID 524)
–Software index P 03 (ID 560)
Introduction of service mode function S 27.
–Software index P 04 (ID 585)
1. Parameter adjustment of all "vario TD”programs.
The washing parameters of programs "vario TD", "vario TD AN" and "B"
(vario TD NR of G 7882/CD) increased from...

1. If an aerosol-injection steam condenser is installed, the steam condenser
(DHK) pause can also be activated without drying in order to, e.g.,
reduce the level of steam escaping with high-temperature programs.
2. Depending on model (with/without steam condenser (DHK) and with/
without drying unit (TA)), service mode 2 (level S 26 - Function 3) offers
various options as follows:
1. S 26 - "-": DHK (aerosol-injection steam condenser) not installed
2. S 26 - 30: Without additional steam condenser...

7. If a reduced water quantity is programmed in program blocks VR2, SP1
or SP2, then heating should not take place in these blocks because the
wash pressure is not sufficiently constant and this can lead to the
registration of a fault (F 3EorF 27). The interdependence has been
adjusted.
8. With the electronic module EGPL 081 P 05 (ID 860), a diagnostic
support file (DUD) for the Miele diagnostic utility (MDU) has been created
for the first time.
9. In the programming mode, the range of dispensing options...

this fault is registered when an interface is active, the fault codeF 13is
always correctly generated. The modified software ensures that this
communication problem is correctly identified.
6. A new diagnostic support file (DUD) for the Miele diagnostic utility (MDU)
has been created for electronic module EGPL 081 P 06 (ID 1180).
7. With the introduction of the new control, the machine technical
documentation is no longer located behind the cover plate under the
door, but is now included with the machine...

F 32: Faulty activation, dispenser relay on EGPL or EZL stuck
(dispensing relay).
F 33: Maximum permitted activation time exceeded (dispensing time).
6. Control modifications, corrections and extensions.
The automatic ventilation times stored in the electronic module have
been adjusted for the internal dispenser pump DOS 3.
When an electronic module is reset, the dispenser control settings (E 02
- Functions 9 - 11) are no longer overwritten. This means that now when
an old electronic module is replaced...