Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Upgrades And Additions Manual

DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
What’s New in Release 8.2si 
xi  
Discontinued hardware
No equipment was discontinued with Release 8.2si.
To o l s
No new tools became available with Release 8.2si.
Commands, screens, and fields
The following commands and screens are new to or affected by Release 8.2si. 
The number of screens has changed, and some fields have moved to different 
screens.
Procedures
The following procedures and steps changed or...

DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
What’s New in Release 8.2si 
xii  
Upgrade tips
The following upgrade tips were generated from problems identified in the 
laboratory or during early introduction.
nThe pooled modem requires a Lucent WP90110 L7 power supply. 
Although integrated conversion can use either the L5 or L7, the combined 
only works with an L7.
Cautions and warnings
The following new cautions and warnings were generated from problems...

DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
What’s New in Release 8.2si 
xiii  
Product names
The following products have been renamed.
Product name Old name
IP Interface Assembly 
(TN802B)IP trunk (TN802) 

DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
What’s New in Release 8.2si 
xiv   

About This Book 
xv Offer Categories 
DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
About This Book
This book provides the procedures for upgrading existing systems to a 
DEFINITY® Enterprise Communications Server Release 8.2. This book also 
contains instructions for adding equipment to an existing Release 8.2 system.
This document covers information related to DEFINITY ECS Release 8.2 and is 
intended for use by a trained installation technician.
Offer...

DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
About This Book 
xvi Upgrade Paths 
Upgrade Paths
Table 1 correlates each upgrade to an associated chapter number.
NOTE:
The oldest load that can be directly upgraded to R6 is V2 4.5. If the existing 
load is older than that, it must first be upgraded to V2 4.5. This can be done 
with Remediation 687DR. Also, the existing load must be V1 8.0 or later to 
update to V2 4.5. If it is not, it can be upgraded to 8.0...

DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
About This Book 
xvii Related Documents 
The following table indicates the processes and their corresponding time 
allotment. Not all processes are required for every upgrade; the table shows 
maximum times and includes high and critical reliability processes.
Related Documents
As supplemental information, the following books may be required to perform 
upgrades and additions to DEFINITY ECS Release 8 systems:...

DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
About This Book 
xviii Conventions Used in This Book 
nDEFINITY Enterprise Communications Server Release 8 Administration for 
Network Connectivity
nSwitch Administration for DEFINITY AUDIX
Conventions Used in This Book
This book uses the following conventions:
nKeyboard keys are shown as: En te r.
nInformation you type is shown as: save announcements. To submit the 
command you typed, press the 
En te r key in...

DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
About This Book 
xix How to Order Books 
How to Order Books
In addition to this book, other description, installation and test, maintenance, and 
administration books are available. A complete list of DEFINITY books can be 
found in the 
Business Communications System Publications Catalog, 
555-000-010.
This book and any other DEFINITY books can be ordered directly from the Lucent 
Technologies Business...

DEFINITY ECS Release 8.2
Upgrades and Additions for R8.2si  555-233-122  Issue 1
April 2000
About This Book 
xx Where to Call for Technical Support 
Single-Mode Fiber Attenuators
Attenuators may be required when using single-mode fiber. See the table below.
A different value attenuator may be required on the transmit side versus the 
receive side, even though the fiber span is between the same 2 cabinets (local 
and remote cabinet). Refer to 
DEFINITY Enterprise Communications Server 
Release 8...