Lexmark X792 Manual

Menu itemDescription
NPA Mode
Auto
On
OffSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is then updated.
Parallel Buffer
Auto
3KB to [maximum size allowed]
DisabledSets the size of the parallel input buffer
Notes:
Auto is the factory...

Menu itemDescription
Honor Init
Off
OnDetermines if the printer honors printer hardware initialization requests from the
computer
Notes:
Off is the factory default setting.
The computer requests initialization by activating the Init signal from the
parallel port. Many personal computers activate the Init signal each time the
computer is turned on.
Parallel Mode 2
On
OffDetermines if the parallel port data is sampled on the leading or trailing edge of a
strobe
Note: On is the factory default setting.
Mac...

Menu itemDescription
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job received
through a serial port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When set to Off, the printer does not examine incoming data. The printer uses
PCL emulation if PCL SmartSwitch is set to On. It uses the default printer
language specified in the Setup menu if PCL SmartSwitch is set to Off.
NPA Mode
Auto
On
OffSets the printer to...

Menu itemDescription
Protocol
DTR
DTR/DSR
XON/XOFF
XON/XOFF/DTR
XONXOFF/DTRDSRSelects the hardware and software handshaking settings for the serial port
Notes:
DTR is the factory default setting.
DTR/DSR is a hardware handshaking setting.
XON/XOFF is a software handshaking setting.
XON/XOFF/DTR and XON/XOFF/DTR/DSR are combined hardware and
software handshaking settings.
Robust XON
Off
OnDetermines whether the printer communicates availability to the computer
Notes:
Off is the factory default setting....

SMTP Setup menu
Menu itemDescription
Primary SMTP GatewaySpecifies SMTP server gateway and port information
Note: 25 is the default SMTP gateway port.
Primary SMTP Gateway Port
Secondary SMTP Gateway
Secondary SMTP Gateway Port
SMTP Timeout
5–30Specifies the amount of time in seconds before the server stops trying to
send an e‑mail
Note: 30 seconds is the factory default setting.
Reply AddressSpecifies a reply address of up to 128 characters in the e-mail sent by the
printer
Use SSL
Disabled
Negotiate...

Security menu
Edit Security Setups menu
UseTo
Edit Backup Password
Use Backup Password
Off
On
PasswordCreate a backup password.
Notes:
Off is the factory default setting for Use Backup Password.
This menu item appears only if a backup password exists.
Edit Building Blocks
Internal Accounts
NTLM
Simple Kerberos Setup
Kerberos Setup
Active Directory
LDAP
LDAP+GSSAPI
Password
PINEdit settings for Internal Accounts, NTLM, Simple Kerberos Setup, Kerberos Setup,
Active Directory, LDAP, Password, and PIN.
Edit...

Miscellaneous Security Settings menu
Menu itemDescription
Login Restrictions
Login failures
Failure time frame
Lockout time
Panel Login Timeout
Remote Login TimeoutLimits the number and time frames of failed login attempts from the printer control
panel before all users are locked out
Notes:
“Login failures” specifies the number of failed login attempts before users are
locked out. Settings range from 1–10 attempts is the factory default setting.
“Failure time frame” specifies the time frame during which...

Confidential Print menu
UseTo
Max Invalid PIN
Off
2–10Limit the number of times an invalid PIN can be entered.
Note: Once the limit is reached, the print jobs for that user name and PIN are deleted.
Confidential Job Expiration
Off
1 hour
4 hours
24 hours
1 weekLimit the amount of time a confidential print job stays in the printer before it is deleted.
Notes:
If the Confidential Job Expiration setting is changed while confidential print jobs reside
in the printer RAM, then the expiration time for those...

UseTo
Automatic Method
Single pass
Multi‑passSpecify a method for automatic disk wiping.
Notes:
Single pass is the factory default setting.
Highly confidential information should be erased using only the Multiple pass
method.
Manual Method
Single pass
Multi‑passSpecify a method for manual disk wiping.
Note: Single pass is the factory default setting.
Scheduled Method
Single pass
Multi‑passSpecify a method for a scheduled disk wiping.
Note: Single pass is the factory default setting.
Security Audit Log...

Menu itemDescription
Configure Log
Enable Audit
Enable Remote Syslog
Remote Syslog Server
Remote Syslog Port
Remote Syslog Method
Remote Syslog Facility
Log full behavior
Admin’s e-mail address
Digitally sign exports
Severity of events to log
Remote Syslog non-logged
events
E-mail log cleared alert
E-mail log wrapped alert
E-mail % full alert
% full alert level
E-mail log exported alert
E-mail log settings changed alert
Log line endingsSpecifies whether and how the audit logs are created
Note: Factory...