Lexmark X642e User Manual

81 5
Place the print media in the tray:
Note:Paper must be loaded differently in the trays, depending on the options you have 
installed.
Print side facing down for simplex (single-sided) printing
Print side facing up for duplex printing
Note:Do not fill paper above the load line. Overfilling the tray may cause jams.
6Squeeze the side guide tab, and slide the guide toward the inside of the tray until it lightly 
rests against the edge of the media.
Downloaded From ManualsPrinter.com Manuals 

82 7
Insert the tray into the MFP.
SimplexDuplex
Downloaded From ManualsPrinter.com Manuals 

83
Setting the Paper Type and Paper Size
After setting the Paper Type and Paper Size to the correct values for the type and size used in the 
trays, then any trays containing the same size and type are automatically linked by the MFP.
Note:If the size of the media you are loading is the same size of the media previously 
loaded, do not change the Paper Size setting.
To change the Paper Size and Paper Type setting:
1Make sure the MFP is on.
2Press Menu on the control panel.
3Touch Paper Menu.
4Touch Paper...

84
finisher affects how letterhead documents should be loaded for duplexing. You can print simplex jobs 
on letterhead (or other preprinted media) that has been loaded specifically for duplex printing by 
changing the value in the Paper Loading menu.
To load print media:
Note:Do not add or remove print media when the MFP is printing from the multipurpose 
feeder or when the control panel indicator light is blinking. Doing so may cause a 
jam.
1Push the release latch, and lower the multipurpose feeder....

85 4
Flex the sheets or envelopes back and forth to loosen them, then fan them. Do not fold or 
crease the print media. Straighten the edges on a level surface.
Note:Hold transparencies by the edges, and avoid touching the print side. Fan the stack 
of transparencies to prevent jams. Be careful not to scratch or leave fingerprints on 
the transparencies.
5Load the media in the tray.
Use the stack height label as a guide for stack height when loading print media.
Loading paper, transparencies, or...

86
Do not fill paper above the load line. Overfilling the tray may cause jams.
6Slide the side guide toward the inside of the tray until it lightly rests against the edge of the 
media.
7Set the Paper Size and Paper Type for the multipurpose feeder to the correct value for the 
print media you loaded. See Setting the Paper Type and Paper Size for more information.
Simplex (single sided) Duplex
Downloaded From ManualsPrinter.com Manuals 

87
Closing the multipurpose feeder
1Remove print media from the multipurpose feeder.
2Push the extension tray in.
3Close the multipurpose feeder cover.
Loading the 2000-sheet drawer
The optional 2000-sheet drawer can be used for plain paper, letterhead or other preprinted paper, 
labels, or transparencies. For trouble-free printing, make sure you:
Do not load print media above the load line. 
Do not fold or crease the paper.
Do not mix sizes or weights in the same source.
Do not open the door or...

88
To load the 2000-sheet drawer:
1Open the loading door. If the elevator tray is not already in the lowered position, push the 
elevator button to lower the tray.
2Flex the sheets back and forth to loosen them, then fan them. Do not fold or crease the print 
media. Straighten the edges on a level surface.
1234567890#
Elevator button
Downloaded From ManualsPrinter.com Manuals 

89 3
Slightly bend the stack of print media as shown, and place it on the elevator tray with the 
preferred print side facing down. Align the stack of print media to the back of the drawer.
Note:For duplex printing, letterhead or other preprinted paper must be loaded differently.
Carefully align each stack as you load it to ensure a smooth edge where the stacks meet. Do 
not load print media above the load line.
Note:When loading more than one ream of paper, we recommend you remove the top 
and bottom...

90
Loading the envelope feeder
The optional envelope feeder can accept a variety of envelope sizes. However, the envelope feeder 
must be adjusted correctly to ensure trouble-free printing. To load the envelope feeder:
1Adjust the envelope support for the length of envelope you are loading.
Fully closed (pushed in toward the MFP) for short envelopes
Extended to the middle position for medium-length envelopes
Fully open (extended to its full length) for long envelopes
Warning:Do not place objects on...