Lexmark X264 Service Manual

Repair information 4-83
7013-XXX
Wireless antenna removal
1.Remove the right side printer cover. See “Right side printer cover removal” on page 4-73.
2.Disconnect the wireless card cable (A) from the wireless card.
3.Remove the two screws (B) from the antenna.
4.Remove the wireless antenna.
A
B 

4-84  Service Manual 7013-XXX
Wireless card removal
1.Remove the right side printer cover. See “Right side printer cover removal” on page 4-73.
2.Remove the wireless antenna. See “Wireless antenna removal” on page 4-83.
3.Pinch the standoff (A) with a pair of needle-nosed pliers to remove the wireless card.
A 

Locations and connections 5-1
7013-XXX
5.  Locations and connections
Locations
Front view
Number Part
1
Front door release button
2Printer control panel
3Automatic document feeder (ADF)
4Controller board door
5Front door
6Multipurpose feeder door
Note: This could be the manual feeder door, 
depending on the printer model.
7
Standard 25-sheet tray (Tray 1)
8Standard exit bin
123
4
5
6
7
8 

5-2  Service Manual 7013-XXX
Rear view
Number Part
1
Rear door
2Ethernet port
3Wireless antenna
Note: The wireless antenna appears on 
wireless models only.
4
Fax ports
Note: Fax ports appear on fax models only.
5
USB port
6Printer power cord socket
7Power switch
8Locking device
1
2
8
47
3
6
5 

Locations and connections 5-3
7013-XXX
Controller board connector pin values 

5-4  Service Manual 7013-XXX
Note:  See the wiring diagram at back of book.
These values were measured with all connections made (plugged) or with only one connector at a time 
unplugged to expose the pins. Always disconnect and connect with the printer power off. Otherwise, the values 
below may not match.
Connector Pin # Value  Connector description
Print engine connectors
J3 1, 4 Ground Wireless
55V dc
63.3V dc
J5 1 0.6 V dc Toner level sensor
2 Ground
30 V dc
J6 1 5 V dc (door closed) Cover open...

Locations and connections 5-5
7013-XXX
J19 1, 4 0.1 V dc, 5Vdc unplugged Main motor
2, 3, 6 5 V dc
5 Ground
7, 8, 9 24 V dc
J22 1, 3, 5, 7, 11, 13, 
155V dc unplugged LVPS/HVPS
4 5V dc unplugged
6 24V dc unplugged
17, 19 24V dc unplugged
J26 1 1.1 V dc, 5V dc unplugged MPF sensor
25 V dc
3, 4 Ground
J27 1 24 V dc Paper feed clutch
2 24 V dc, 0V dc unplugged
J28 1 24 V dc MPF clutch
2 24 V dc, 0V dc unplugged
J29 1 24 V dc Manual clutch solenoid
2 24 V dc, 0V dc unplugged
J30 1, 4 1.1 V dc, 5V dc...

5-6  Service Manual 7013-XXX
J4 1 I0A_ADF_C ADF
2 I1A_ADF_C
3 Ground
4 DIRA_ADF_C
5 Ground
6 I0B_ADF_C
7 I1B_ADF_C
8 Ground
9 DIRB_ADF_C
10 Ground
11 +24V
12 +24V
13 Ground
14 +5V
15 PAP_PRES2_2
16 PAP_PRES3_C
17 VREF2_ADF_C
18 PAP_PRES_C
19 ADF_CVR_C
20 FIRST_SCAN_C
21 FB_CVR_C
22 SOL_EN_2
J39 1 FAX_CS Fax
2 Ground
3 SPI_DI
4 Ground
5 SPI_DOUT
6 Ground
7 SPI_SCLK
8 Ground
9FAX_INT
10 +5V
11 RESET_TO_MODEM
12 +3.3V
13 +3.3V
14 NC_J25_J4
JFBM1 1 FBA- Flatbed motor
2FBA
3FBB
4FBB- Connector Pin # Value...

Preventive maintenance 6-1
7013-XXX
6.  Preventive maintenance
This chapter describes procedures for printer preventive maintenance. Follow these recommendations to help 
prevent problems and maintain optimum performance.
Safety inspection guide
The purpose of this inspection guide is to aid you in identifying unsafe conditions.
If any unsafe conditions exist, then find out how serious the hazard could be and if you can continue before you 
correct the hazard.
Check the following items:
•Damaged,...

6-2  Service Manual 7013-XXX
100 V maintenance kit
Note: The fuser maintenance kit installation is 
recommended every 120,000 pages.
Note: The kit includes:
•  Fuser (P/N 40X5346)
• Tray 1 ACM feed tires (P/N 40X5451) 
Transfer roll (P/N 40X5364)
40X5402
ADF Maintenance kit40X5807
ADF separator roll 40X7545
ADF separator pad40X8419
Exit guide 40X5372
Maintenance kits
Description Part number