Lexmark X204n User Manual

Waiting
The printer has received data to print, but is waiting for an End‑of‑Job command, a Form Feed command, or additional
data.
Press  to print the contents of the buffer.
Cancel the current print job.
31.yy Replace defective or missing cartridge
The toner cartridge is either missing or not functioning properly.
Try one or more of the following:
Remove the toner cartridge, and then reinstall it.
Remove the toner cartridge, and then install a new one.
30 Invalid refill, change toner cartridge
The...

39 Complex page, some data may not have printed
Try one or more of the following:
Press the arrow buttons until Continue appears, and then press  to clear the message and continue printing.
Cancel the current print job.
54 Standard network software error
Try one or more of the following:
Press the arrow buttons until Continue appears, and then press  to continue printing.
Turn the printer off and then back on to reset the printer.
Upgrade (flash) the network firmware in the printer or print server.
54...

200–250 paper jam
1Clear the paper path. For more information, see “Clearing jams” on page 136.
2After clearing the paper path, press  to resume printing.
290–294 paper jams
1Remove all original documents from the ADF.
2Open the ADF cover.
3Unlock the separator roll.
4Remove the separator roll.
Troubleshooting
133
Downloaded From ManualsPrinter.com Manuals 

5Remove the jammed paper.
6Reinstall the separator roll.
7Lock the separator roll.
8Close the ADF cover.
Troubleshooting
134
Downloaded From ManualsPrinter.com Manuals 

9Open the scanner cover, and then remove any jammed pages.
3DEF6MNO9WXYZ#
2ABC5JKL8TUV0
1@!.GHI4P
Q
R
S7*
10Press .
840.01 Scanner Disabled
This message indicates that the scanner has been disabled by the system support person.
840.02 Scanner Auto Disabled
This message indicates that the printer identified a problem with the scanner and automatically disabled it.
1Remove all pages from the ADF.
2Turn the printer off.
3Wait 15 seconds, and then turn the printer on.
4Place the document in the ADF, and then...

Clearing jams
By carefully selecting paper and loading it properly, you can avoid most jams. If jams do occur, follow the steps outlined
in this chapter.
To clear a jam message and resume printing, clear the entire paper path, and then press 
. If Jam Recovery is set to
On, the printer prints a new copy of the page that jammed. If Jam Recovery is set to Auto, the printer may or may not
print a new copy of the page that jammed.
Avoiding jams
The following hints can help you avoid jams:
Paper tray...

200–201 paper jam
200 paper jam
1
Remove the tray from the printer.
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4P
Q
R
S7*
2Remove the jam if you see it here.
3DEF6MNO9WXYZ#
2ABC5JKL8TUV0
1@!.GHI4P
Q
R
S7*
3If you do not see it, see “201 paper jam” on page 138.
Troubleshooting
137
Downloaded From ManualsPrinter.com Manuals 

201 paper jam
1
Open the front door, and then remove the photoconductor kit and toner cartridge.
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4PQRS7*
2Lift the flap at the front of the printer, and remove any jammed sheets.
3Align and insert the photoconductor kit and toner cartridge.
4Close the front door.
5Insert the tray.
6Press .
Troubleshooting
138
Downloaded From ManualsPrinter.com Manuals 

202 paper jam
CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching.
1Open the front door, and then remove the photoconductor kit and toner cartridge.
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4PQRS7*
2Lift the flap at the front of the printer, and then remove any jammed sheets.
Troubleshooting
139
Downloaded From ManualsPrinter.com Manuals 

3Open the rear door.
4Remove the jam.
5Close the rear door.
6Align and insert the photoconductor kit and toner cartridge.
7Close the front door.
8Press .
Troubleshooting
140
Downloaded From ManualsPrinter.com Manuals