Lexmark X204n User Manual

2Press the button on the base of the photoconductor kit, and then pull the toner cartridge out using the handle.
3D
E
F6M
N
O9W
X
Y
Z#2A
B
C5J
K
L8T
U
V01@!.G
H
I4PQRS7*
2
1
3Unpack the new toner cartridge.
4Shake the cartridge in all directions to distribute the toner.
Maintaining the printer
121
Downloaded From ManualsPrinter.com Manuals 

5Install the new toner cartridge by aligning the rollers on the toner cartridge with the arrows on the tracks of the
photoconductor kit. Push the toner cartridge in as far as it will go. The cartridge clicks into place when correctly
installed.
3DEF6MNO9WXYZ#
2ABC5JKL8TUV0
1@!.GHI4P
Q
R
S7*
6Close the front door.
Replacing the photoconductor kit
The printer automatically notifies you before the photoconductor kit reaches a page maximum by showing 84 PC
Kit life warning or 84 Replace PC Kit on the...

1Open the front door by pressing the button on the left side of the printer and lowering the front door.
3D
E
F6M
N
O9W
X
Y
Z#2A
B
C5J
K
L8T
U
V01@!.G
H
I4PQRS7*
2Pull the photoconductor kit and toner cartridge out of the printer as a unit by pulling on the toner cartridge handle.
Note: The photoconductor kit and toner cartridge form a unit.
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4PQRS7*
Place the unit on a flat, clean surface.
Maintaining the printer
123
Downloaded From ManualsPrinter.com Manuals 

3Press the button on the base of the photoconductor kit. Pull the toner cartridge up and out using the handle.
2
1
4Unpack the new photoconductor kit. Be careful not to touch the photoconductor drum.
Warning—Potential Damage: When replacing the photoconductor kit, do not leave the kit exposed to direct
light for an extended period of time. Extended light exposure can cause significant print quality problems.
Maintaining the printer
124
Downloaded From ManualsPrinter.com Manuals 

5Insert the toner cartridge into the photoconductor kit by aligning the rollers on the toner cartridge with the tracks.
Push the toner cartridge until it clicks into place.
6Install the unit into the printer by aligning the arrows on the guides of the unit with the arrows in the printer. Push
the unit in as far as it will go.
3D
E
F6M
N
O9W
X
Y
Z#2A
B
C5J
K
L8T
U
V01@!.G
H
I4PQRS7*
7After you replace the photoconductor kit, reset the photoconductor counter. To reset the counter, see the
instruction sheet...

Use the handholds located on both sides of the printer to lift it.
Make sure your fingers are not under the printer when you set it down.
Before setting up the printer, make sure there is adequate clearance around it. For more information, see “Selecting
a location for the printer” on page 12.
The printer and options can be safely moved to another location by following these precautions:
Any cart used to move the printer must be able to support its weight and have a large enough surface to support
the...

Administrative support
Finding advanced networking and administrator information
This chapter covers basic administrative support tasks. For more advanced system support tasks, see the Networking
Guide on the Software and Documentation CD and the Embedded Web Server Administrators Guide on the Lexmark
Web site at www.lexmark.com.
Using the Embedded Web Server
If the printer is installed on a network, the Embedded Web Server is available for a range of functions including:
Viewing a virtual display of the...

Checking the device status
Using the Embedded Web Server, you can view paper tray settings, the level of toner in the print cartridge, the
percentage of life remaining in the maintenance kit, and capacity measurements of certain printer parts. To view the
device status:
1Type the printer IP address in the address field of your Web browser.
Note: If you do not know the IP address of the printer, then print a network setup page and locate the IP
address in the TCP/IP section.
2Click Device Status.
Setting...

Troubleshooting
Checking an unresponsive printer
If there are basic printer problems, or the printer is unresponsive, make sure:
The power cord is plugged into the printer and a properly grounded electrical outlet.
The electrical outlet is not turned off by any switch.
The Ground Fault Circuit Interrupter (GFCI) has not tripped.
The printer is not plugged into any surge protectors, uninterrupted power supplies, or extension cords.
Other electronic equipment plugged into the outlet is working.
The printer...

Understanding printer messages
Close front door
Close the front door of the printer.
Invalid Engine Code
You need to download valid engine code for the printer.
Note: Engine code may be downloaded while this message appears on the display.
Load  with 
Try one or more of the following:
Load the paper tray with the correct paper type and size.
Cancel the current job.
Network/Network 
The printer is connected to the network.
Network indicates that the printer is using the standard network port built into...