Home > Lexmark > Printer > Lexmark C935dtn User Manual

Lexmark C935dtn User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Lexmark C935dtn User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							–Have windows, holes, perforations, cutouts, or embossing
    –Have metal clasps, string ties, or folding bars
    –Have an interlocking design
    –Have postage stamps attached
    –Have any exposed adhesive when the flap is in the sealed or closed position
    –Have bent corners
    –Have rough, cockle, or laid finishes
    Adjust the width guide to fit the width of the envelopes.
    Note: A combination of high humidity (over 60%) and the high printing temperature may wrinkle or seal envelopes.
    Using labels
    Print samples on the labels being considered for use before buying large quantities.
    For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide available on
    the Lexmark Web site at www.lexmark.com/publications.
    When printing on labels:
    From MarkVision Professional, Print Properties, or the control panel, set the Paper Type to Labels.
    Use only letter, A4, or legal‑size label sheets.
    Use labels designed specifically for laser printers. Check with the manufacturer or vendor to verify that label
    adhesives, face sheet (printable stock), and topcoats can withstand temperatures up to 230°C (446°F) and pressure
    up to 25 psi without delaminating, oozing around the edges, or releasing hazardous fumes. Do not use vinyl labels.
    Do not use labels with slick backing material.
    Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets
    also contaminate the printer and the cartridge with adhesive, and could void the printer and cartridge warranties.
    Do not use labels with exposed adhesive.
    Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die‑cuts of the label.
    Be sure adhesive backing does not reach to the sheet edge. Zone coating of the adhesive at least 1 mm (0.04 in.)
    away from edges is recommended. Adhesive material contaminates the printer and could void the warranty.
    If zone coating of the adhesive is not possible, remove a 1.6 mm (0.06 in.) strip on the leading and driver edge, and
    use a non‑oozing adhesive.
    Portrait orientation works best, especially when printing bar codes.
    Using card stock
    Card stock is heavy, single‑ply print media. Many of its variable characteristics, such as moisture content, thickness,
    and texture, can significantly impact print quality. Print samples on the card stock being considered for use before
    buying large quantities.
    When printing on card stock:
    From MarkVision Professional, or the control panel:
    1Set the Paper Type to Card Stock.
    2Select a Card Stock Texture setting. Paper and specialty media guide41
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or
    other paper handling problems.
    Check with the manufacturer or vendor to ensure the card stock can withstand temperatures up to 230°C (446°F)
    without releasing hazardous emissions.
    Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting
    introduces semi‑liquid and volatile components into the printer.
    Use grain long card stock when possible.
    Storing paper
    Use these paper storage guidelines to help avoid jams and uneven print quality:
    For best results, store paper where the temperature is 21°C (70°F) and the relative humidity is 40%. Most label
    manufacturers recommend printing in a temperature range of 18 to 24°C (65 to 75°F) with relative humidity between
    40 and 60%.
    Store paper in cartons when possible, on a pallet or shelf, rather than on the floor.
    Store individual packages on a flat surface.
    Do not store anything on top of individual paper packages.
    Supported paper sizes, types, and weights
    The following tables provide information on standard and optional paper sources and the types of paper they support.
    Note: To use a paper size that is unlisted, configure a Universal Paper Size.
    For information on card stock and labels, see the Card Stock & Label Guide.
    Paper sizes supported by the printer
    Paper sizeDimensions520‑sheet trays
    (standard or
    optional)High capacity
    feederMultipurpose
    feederDuplex unit
    A3297 x 420 mm
    (11.7 x 16.5 in.)
    X
    A4210 x 297 mm
    (8.3 x 11.7 in.)
    A51148 x 210 mm
    (5.8 x 8.3 in.)XX
    Executive184 x 267 mm
    (7.3 x 10.5 in.)XX
    1 The printer cannot simultaneously sense A5 and statement paper sizes. From the Size Sensing menu, specify which size
    you want the printer to detect. This setting applies to all automatic trays except the multipurpose feeder. The multipurpose
    feeder can support both sizes.
    2 Measurements apply to simplex (one‑sided) printing only. For duplex (two‑sided) printing, the minimum size is
    140 x 148 mm (5.5 x 5.8 in.) and the maximum size is 297 x 432 mm (11.7 x 17 in.).
    Paper and specialty media guide42
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Paper sizeDimensions520‑sheet trays
    (standard or
    optional)High capacity
    feederMultipurpose
    feederDuplex unit
    Folio216 x 330 mm
    (8.5 x 13 in.)
    X
    JIS B4257 x 364 mm
    (10.1 x 14.3 in.)X
    JIS B5182 x 257 mm
    (7.2 x 10.1 in.)
    Legal216 x 356 mm
    (8.5 x 14 in.)X
    Letter216 x 279 mm
    (8.5 x 11 in.)
    Statement1140 x 216 mm
    (5.5 x 8.5 in.)XX
    Tabloid279 x 432 mm
    (11 x 17 in.)
    X
    Universal100 x 148 mm
    (3.9 x 5.8 in.) up to
    305 x 483 mm
    (11.7 x 19 in.)
    2
    XX
    7 3/4 Envelope
    (Monarch)98 x 191 mm
    (3.9 x 7.5 in.)XXX
    B5 Envelope176 x 250 mm
    (6.9 x 9.8 in.)XX
    X
    C5 Envelope162 x 229 mm
    (6.4 x 9 in.)XX
    X
    9 Envelope98 x 225 mm
    (3.9 x 8.9 in.)XX
    X
    10 Envelope105 x 241 mm
    (4.1 x 9.5 in.)XX
    X
    DL Envelope110 x 220 mm
    (4.3 x 8.7 in.)XX
    X
    1 The printer cannot simultaneously sense A5 and statement paper sizes. From the Size Sensing menu, specify which size
    you want the printer to detect. This setting applies to all automatic trays except the multipurpose feeder. The multipurpose
    feeder can support both sizes.
    2 Measurements apply to simplex (one‑sided) printing only. For duplex (two‑sided) printing, the minimum size is
    140 x 148 mm (5.5 x 5.8 in.) and the maximum size is 297 x 432 mm (11.7 x 17 in.).
    Paper and specialty media guide43
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Paper types and weights supported by the printer
    The printer engine supports 60–220 g/m2 (16–60 lb) paper weights. The duplex unit supports 63–170 g/m2 (17–45 lb)
    paper weights.
    Paper type520‑sheet traysHigh capacity feederMultipurpose feederDuplex unit
    Plain Paper
    Bond
    Letterhead
    Preprinted
    Colored Paper
    Card stock
    Glossy paper X XX
    Paper labels
    *XX
    TransparenciesX
    Envelopes X X
    X
    * Vinyl labels are not supported.
    Paper types and weights supported by the finisher
    Use this table to determine the possible output destinations of print jobs which use supported paper types and weights.
    The paper capacity of each output bin is listed in parentheses. Paper capacity estimations are calculated based on
    75 g/m
    2 (20 lb) paper.
    The Finisher standard bin and Bin 1 support 60–220 g/m
    2 (16–60 lb) paper weights. Bin 2 (booklet‑maker) supports 60–
    90 g/m
    2 (16–24 lb) paper weights plus one additional cover weighted up to 220 g/m2 (60 lb).
    Paper typeHorizontal transport
    unit
    (50 sheets)Finisher standard
    bin (500 sheets)Bin 1 (1500/3000
    sheets)*Bin 2
    (300 sheets)
    Plain Paper
    Bond
    Letterhead
    Preprinted
    Colored Paper
    Card stock
    * Bin 1 of the booklet finisher supports 1500 sheets. Bin 1 of the standard finisher supports 3000 sheets.
    Paper and specialty media guide44
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Paper typeHorizontal transport
    unit
    (50 sheets)Finisher standard
    bin (500 sheets)Bin 1 (1500/3000
    sheets)*Bin 2
    (300 sheets)
    Glossy paper
    XX
    Labels
    XX
    Transparencies
    XX
    Envelopes
    XX X
    * Bin 1 of the booklet finisher supports 1500 sheets. Bin 1 of the standard finisher supports 3000 sheets.
    Supported finishing features
    1Horizontal transport unit
    2Finisher standard bin
    3Finisher bin 1
    4Finisher bin 2 (booklet‑maker)
    Notes:
    The finisher shown above, is the booklet finisher. Bin 2 is available only when the booklet finisher is installed.
    All paper capacities are based on 75 g/m2 (20 lb) paper.
    Horizonal transport unit
    The paper capacity is 50 sheets.
    Finishing options are not supported in this bin. Paper and specialty media guide45
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Envelopes are routed here.
    Universal paper is routed here when it is longer than 483 mm (19 in.) or shorter than 148 mm (5.8 in.).
    Finisher standard bin
    The paper capacity is 500 sheets.
    Envelopes and executive‑size paper are not supported in this bin.
    Finishing options are not supported in this bin.
    Bin 1
    The paper capacity is 3000 sheets when the standard finisher is installed.
    The paper capacity is 1500 sheets when the booklet finisher is installed.
    Bin 1 finishing features
    SizePunch*OffsetSingle/double stapleDouble dual staple
    A3
    A4
    A5 X X X X
    Executive
    X
    Folio X
    X
    JIS B4
    X
    JIS B5
    X
    Legal X
    X
    Letter
    Statement X X X
    TabloidX
    Universal
    Envelopes (any size) X X X X
    * For the Universal paper size, the finishing edge must be at least 9 in. (229 mm) for a 3‑hole punch and 10 in. (254 mm) for
    a 4‑hole punch.
    Punch—Two‑, three‑, or four‑hole punch settings
    Single staple—One staple
    Double staple—Two staples
    Double dual staple—Two sets of two staples. This setting is supported only for widths between 8 in. (203 mm) and 11.7 in.
    (297 mm) with lengths between 7.2 in. (182 mm) and 17 in. (432 mm).
    Paper and specialty media guide46
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Bin 2 (booklet‑maker)
    Bin 2 is available only when the booklet finisher is installed. The paper capacity of Bin 2 (booklet‑maker) is 300 sheets
    or 20 sets of 15‑sheet booklets.
    Bin 2 finishing features
    SizeBi foldBooklet foldSaddle staple
    A3
    A4 (only SEF)
    A5XXX
    ExecutiveXXX
    Folio
    JIS B4
    JIS B5XXX
    Legal
    Letter (only SEF)
    Statement X X X
    Tabloid
    UniversalXXX
    Envelopes (any size) X X X
    SEF—The paper is loaded in the short edge orientation. The short edge of the paper enters the printer first.
    Bi fold—Each page is individually folded and stacked separately.
    Booklet fold—A multiple-page job is folded along the center into a single booklet.
    Saddle staple—A booklet‑fold print job is stapled along the center fold.
    Paper and specialty media guide47
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing
    This chapter covers printing, printer reports, and job cancellation. The selection and handling of paper and specialty
    media can affect how reliably documents print. For more information, see Avoiding jams and Storing paper.
    Installing printer software
    A printer driver is software that lets the computer communicate with the printer. The printer software is typically
    installed during the initial printer setup. For more information, see the Setup sheet or Setup Guide that shipped with
    the printer or click Install printer and software on the Software and Documentation CD.
    When Print is chosen from a software application, a dialog representing the printer driver opens. Click Properties,
    Preferences, Options, or Setup from the initial Print dialog to open Print Properties and see all of the available printer
    settings that may be changed. If a feature in Print Properties is unfamiliar, open the online Help for more information.
    Note: Print settings selected from the driver override the default settings selected from the control panel.
    Printing a document from Windows
    1With a document open, click File > Print.
    2Click Properties, Preferences, Options, or Setup.
    3Adjust the settings.
    4Click OK.
    5Click OK or Print.
    Printing a document from a Macintosh computer
    1With a document open, choose File > Print.
    2From the Copies & Pages or General pop‑up menu, adjust the settings.
    3Click OK or Print.
    Printing confidential and other held jobs
    Holding jobs in the printer
    When sending a job to the printer, you can specify in the Print Properties that you want the printer to hold the job in
    memory until you start the job from the control panel. All print jobs that can be initiated by the user at the printer are
    called held jobs.
    Note: Confidential, Repeat, Reserve, and Verify print jobs may be deleted if the printer requires extra memory to
    process additional held jobs. Printing48
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Job typeDescription
    Confidential When you send a Confidential print job to the printer, you must create a PIN in
    Print Properties. The PIN must be four digits using the numbers 0–9. The job is held
    in printer memory until you enter the PIN from the control panel and choose to
    print or delete the job.
    Repeat When you send a Repeat print job, the printer prints all requested copies of the
    job and stores the job in memory so you can print additional copies later. You can
    print additional copies as long as the job remains stored in memory.
    Reserve When you send a Reserve print job, the printer does not print the job immediately.
    It stores the job in memory so you can print the job later. The job is held in memory
    until you delete it from the Held Jobs menu.
    Verify When you send a Verify print job, the printer prints one copy and holds the
    remaining copies in printer memory. Verify lets you examine the first copy to see
    if it is satisfactory before printing the remaining copies. Once all copies are printed,
    the job is automatically deleted from printer memory.
    Printing confidential and other held jobs from Windows
    1With a document open, click File > Print.
    2Click Properties, Preferences, Options, or Setup.
    3Click Other Options, and then click Print and Hold.
    4Select your job type (Confidential, Reserve, Repeat, or Verify), and then assign a user name. For a confidential job,
    also enter a four‑digit PIN.
    5Click OK or Print, and then go to the printer to release the job.
    6From the control panel, press  repeatedly until Held jobs appears, and then press .
    7Press  repeatedly until  appears next to your user name, and then press .
    8Press  repeatedly until  appears next to the job type or job name, and then press .
    If you selected a job name, proceed to step 10 on page 49.
    9After selecting your job type, use the keypad to enter your PIN.
    If you enter an invalid PIN, the Invalid PIN screen appears.
    To re‑enter the PIN, make sure Try again appears, and then press .
    To cancel the PIN, press  repeatedly until Cancel appears, and then press .
    10Press  repeatedly until  appears next to the job you want to print, and then press .
    11Press  repeatedly until  appears next to the number of copies you want to print, and then press .
    Note: Use the keypad to enter a number if necessary.
    Confidential and Verify print jobs are automatically deleted from memory after they print. Repeat and Reserve jobs
    continue to be held in the printer until you choose to delete them. Printing49
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing confidential and other held jobs from a Macintosh computer
    1With a document open, choose File > Print.
    2From the Copies & Pages or General pop‑up menu, choose Job Routing.
    aWhen using Mac OS 9 if Job Routing is not a choice from the pop‑up menu, choose Plug‑in Preferences >
    Print Time Filters.
    bTurn down the disclosure triangle to the left of Print Time Filters, and choose Job Routing.
    3From the radio group, select your job type (Confidential, Reserve, Repeat, or Verify), and then assign a user name.
    For a confidential job, also enter a four‑digit PIN.
    4Click OK or Print, and then go to the printer to release the job.
    5From the control panel, press  until Held jobs appears, and then press .
    6Press  until  appears next to your user name, and then press .
    7Press  until  appears next to your job, and then press .
    8For confidential jobs, use the numeric keypad to enter your PIN.
    If you enter an invalid PIN, the Invalid PIN screen appears.
    To re‑enter the PIN, make sure Try again appears, and then press .
    To cancel the PIN, press  until Cancel appears, and then press .
    9Press  until  appears next to the job you want to print, and then press .
    Confidential and Verify print jobs are automatically deleted from memory after they print. Repeat and Reserve jobs
    continue to be held in the printer until you choose to delete them. Printing50
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Lexmark manuals Comments (0)

    Related Manuals for Lexmark C935dtn User Manual