Lexmark C935dtn User Manual

							5Press the ribbon cable connector into the hard disk connector on the system board.
6Flip the hard disk over, and then press the three posts on the mounting plate into the holes on the system board.
The hard disk snaps into place.
7Reinstall the system board.
Installing an internal print server or port interface card
CAUTION—SHOCK HAZARD: Turn the printer off, and unplug the power cord from the wall outlet before
continuing. If you have any other devices attached to the printer, turn them off as well and unplug any cables
going into the printer.
Warning—Potential Damage: System board electrical components are easily damaged by static electricity. Touch
something metal on the printer before touching any system board electronic components or connectors.
Note: A #2 Phillips screwdriver is needed to install an internal print server or port interface card. Installing options21
Downloaded From ManualsPrinter.com Manuals 
						

							An internal print server allows connection from the printer to the local area network (LAN). An optional port interface
card expands the ways the printer can connect to a computer or external print server.
1Access the system board.
2Unpack the internal print server or port interface card.
3Remove the metal plate on the system board tray that covers the connector slot and save the metal plate.
4Align the connector on the internal print server or port interface card with the connector on the system board.
Note: The cable connectors on the side of the optional card must fit through the opening in the faceplate.
5Push the internal print server or port interface card firmly into the card connector on the system board.
6Insert a screw into the hole on the right side of the connector slot. Gently tighten the screw to secure the card to
the system board tray.
7Reinstall the system board. Installing options22
Downloaded From ManualsPrinter.com Manuals 
						

							Reinstalling the system board
Warning—Potential Damage: System board electrical components are easily damaged by static electricity. Touch
something metal on the printer before touching any system board electronic components or connectors.
Note: This operation requires a #2 Phillips screwdriver.
1Gently insert the system board into the printer.
2Replace the cover screws, and then turn them clockwise.
3Tighten the screws firmly.
Attaching cables
Connect the printer to the computer using a USB cable or Ethernet cable. A USB port requires a USB cable. Be sure to
match the USB symbol on the cable with the USB symbol on the printer. Match the appropriate Ethernet cable to the
Ethernet port. Installing options23
Downloaded From ManualsPrinter.com Manuals 
						

							1USB port
2Ethernet port
Installing options24
Downloaded From ManualsPrinter.com Manuals 
						

							Loading paper and specialty media
This section explains how to load the 520-, 867-, and 1133-sheet trays, and the multipurpose feeder. It also includes
information about paper orientation, setting the Paper Size and Paper Type, and linking and unlinking trays.
Setting the Paper Size and Paper Type
The Paper Size setting is determined by the position of the paper guides in the tray for all trays except the multipurpose
feeder. The Paper Size setting for the multipurpose feeder must be set manually. The factory default Paper Type setting
is Plain Paper. The Paper Type setting must be set manually for all trays that do not contain plain paper.
1Make sure the printer is on and Ready appears.
2From the control panel, press .
3Press  repeatedly until Paper Menu appears, and then press .
4Press  repeatedly until Paper Size/Type appears, and then press .
5Press  repeatedly until the correct tray appears, and then press .
6Press  repeatedly until  appears next to the correct size, and then press .
7Press  or  repeatedly until the correct Paper Type setting appears, and then press .
Submitting Selection appears.
Configuring Universal paper settings
The Universal Paper Size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer
menus. Set the Paper Size for the specified tray to Universal when the size you want is not available from the Paper
Size menu. Then, specify all of the following Universal size settings for your paper:
Units of measure (inches or millimeters)
Portrait Height and Portrait Width
Feed Direction
Note: The smallest supported Universal size is 100 x 148 mm (3.9  x 5.8 in.); the largest is 305 x 483 mm
(11.7 x 19 in.).
Specify a unit of measurement
1Make sure the printer is on and Ready appears.
2From the control panel, press .
3Press  repeatedly until Paper Menu appears, and then press .
4Press  repeatedly until Universal Setup appears, and then press . Loading paper and specialty media25
Downloaded From ManualsPrinter.com Manuals 
						

							5Press  repeatedly until Units of Measure appears, and then press .
6Press  repeatedly until  appears next to the correct unit of measure, and then press .
Submitting Selection appears, followed by the Universal Setup menu.
Specify the paper height and width
Defining a specific height and width measurement for the Universal paper size (in the portrait orientation) allows the
printer to support the size, including support for standard features such as duplex printing and printing multiple pages
on one sheet.
1From the Universal Setup menu, press  repeatedly until Portrait Width or Portrait Height appears,
and then press 
.
Note: Select Portrait Height to adjust the paper height setting or Paper Width to adjust the paper
width setting.
2Press  to decrease the setting or  to increase the setting, and then press .
Submitting Selection appears, followed by the Universal Setup menu.
Specify a feed direction
Short Edge is the factory default setting for feed direction for Universal paper settings. The Feed Direction menu will
not appear from the Universal Setup menu unless Long Edge is an available setting. If necessary, specify whether the
short or long edge of the paper will enter the printer first.
1From the Universal Setup menu, press  repeatedly until Feed Direction appears, and then press .
2Press  repeatedly until  appears next to the correct feed direction, and then press .
Submitting Selection appears. Loading paper and specialty media26
Downloaded From ManualsPrinter.com Manuals 
						

							Loading the 520-sheet trays
The Size Sensing setting is only available for A5- and statement-size paper.
Loading the 520‑sheet trays
The printer has a standard 520‑sheet tra y (T ray 1 ), an d it may h ave one o r m ore o ptional 520‑sheet trays. All 520‑sheet
trays support the same paper sizes and types. Paper may be loaded in the trays in either the long‑edge or short‑edge
orientation.
1Grasp the handle, and pull the tray out.
2Squeeze the width guide tabs together as shown, and move the width guide to the correct position for the paper
size being loaded.
Loading paper and specialty media27
Downloaded From ManualsPrinter.com Manuals 
						

							3Squeeze the length guide tab inward as shown, and slide the guide to the correct position for the paper size being
loaded.
Note: Use the size indicators on the bottom of the tray to help position the guides.
4Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the
edges on a level surface.
5Load the paper stack with the recommended print side faceup. Load the paper in either the long‑edge or short‑edge
orientation as shown below:
Notes:
Load sizes larger than A4 in the short‑edge orientation.
Paper must be loaded in the short‑edge orientation to create booklets if the optional booklet finisher is
installed.
Long‑edge orientationShort‑edge orientation
6Make sure the paper guides are secure against the edges of the paper. Loading paper and specialty media28
Downloaded From ManualsPrinter.com Manuals 
						

							7Align the tray, and insert it.
8If a different type of paper was loaded than the type previously loaded in the tray, change the Paper Type setting
for the tray from the control panel.
Using A5 or statement paper sizes
The printer trays cannot distinguish between A5‑ (148 x 210 mm) and statement‑size (140 x 216 mm) paper when both
sizes are loaded in the printer trays. From the Size Sensing menu, specify which size you want the printer to detect.
Load either A5‑ or statement‑size paper in the paper trays, but not both.
Note: The multipurpose feeder does not use auto‑size sensing and can support both A5‑ and statement‑size print
jobs. The Size Sensing setting does not affect the multipurpose feeder settings.
1Load either A5‑ or statement‑size paper in a paper tray.
2Make sure the printer is turned off.
3From the control panel, press and hold  and  while turning the printer on.
4Release both buttons when Performing Self Test appears.
The printer performs its power‑on sequence, and then CONFIG MENU appears.
5Press  repeatedly until SIZE SENSING appears, and then press .
6Press  repeatedly until  appears next to the tray in which the paper is loaded, and then press .
7Press  repeatedly until Auto appears, and then press .
The Statement/A5 menu appears.
8Press  repeatedly until appears next to Sense Statement or Sense A5, and then press .
Submitting Selection appears.
9Press  until Exit Config Menu appears, and then press .
The printer performs its power‑on sequence, and then Ready appears. Loading paper and specialty media29
Downloaded From ManualsPrinter.com Manuals 
						

							Loading the 867‑ and 1133‑sheet trays
Although the 867-sheet tray and the 1133-sheet tray are different in appearance, they support the same paper sizes
and types and require the same process for loading paper. Use these instructions to load paper in either tray:
1Grasp the handle, and open the tray.
2Squeeze the length guide tab inward as shown, and slide the guide to the correct position for the paper size being
loaded.
3Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the
edges on a level surface.
Loading paper and specialty media30
Downloaded From ManualsPrinter.com Manuals