Home > Lexmark > Printer > Lexmark C935dtn User Manual

Lexmark C935dtn User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Lexmark C935dtn User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							4Load the paper stack with the recommended print side faceup.
    5Make sure the paper guides are secure against the edges of the paper.
    6Insert the tray into the printer.
    7If a different type of paper was loaded than the type previously loaded in the tray, change the Paper Type setting
    for the tray from the control panel.
    Using the multipurpose feeder
    1Paper guides
    2Size indicators
    3Stack height limiter
    Loading paper and specialty media31
    Downloaded From ManualsPrinter.com Manuals 
    						
    							1Pull the multipurpose feeder tray down.
    2Grasp the extension, and gently pull it out until it is fully extended.
    3Prepare the paper for loading.
    Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten
    the edges on a level surface.
    Hold transparencies by the edges, and then fan them. Straighten the edges on a level surface.
    Note: Avoid touching the print side of the transparencies. Be careful not to scratch them.
    Flex a stack of envelopes back and forth to loosen them, and then fan them. Straighten the edges on a level
    surface.
    Loading paper and specialty media32
    Downloaded From ManualsPrinter.com Manuals 
    						
    							4Load the paper, and then adjust the paper guides so that they lightly touch the edges of the paper stack.
    Load letter, A4, and transparencies with the recommended print side facedown and the long edge of the paper
    entering the printer first.
    Load A3, A5, B4, folio, legal, and statement paper with the recommended print side facedown and the short
    edge of the paper entering the printer first.
    Notes:
    –Adjust the additional paper guide to accommodate SRA3 and 12 x 19 paper sizes.
    –Do not exceed the maximum stack height by forcing paper under the stack height limiter.
    Load envelopes with the flap side up.
    Warning—Potential Damage: Never use envelopes with stamps, clasps, snaps, windows, coated linings, or
    self‑stick adhesives. These envelopes may severely damage the printer.
    Note: Load only one size and type of paper at a time.
    5Make sure the paper is as far into the multipurpose feeder as it will go with very gentle pushing. Paper should lie
    flat in the multipurpose feeder. Make sure the paper fits loosely in the multipurpose feeder and is not bent or
    wrinkled.
    6From the control panel, set the Paper Size and Paper Type. Loading paper and specialty media33
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Linking and unlinking trays
    Linking trays
    Tray linking is useful for large print jobs or multiple copies. When one linked tray is empty, paper feeds from the next
    linked tray. When the Paper Size and Paper Type settings are the same for any trays, the trays are automatically linked.
    The Paper Size setting is automatically sensed according to the position of the paper guides in each tray except the
    multipurpose feeder. The Paper Size setting for the multipurpose feeder must be set manually from the Paper Size
    menu. The Paper Type setting must be set for all trays from the Paper Type menu. The Paper Type menu and the Paper
    Size menu are both available from the Paper Size/Type menu.
    Unlinking trays
    Unlinked trays have settings that are not the same as the settings of any other tray.
    To unlink a tray, change the following tray settings so that they do not match the settings of any other tray:
    Paper Type (for example: Plain Paper, Letterhead, Custom Type )
    Paper Type names describe the paper characteristics. If the name that best describes your paper is used by linked
    trays, assign a different Paper Type name to the tray, such as Custom Type , or define your own custom name.
    Paper Size (for example: letter, A4, statement)
    Load a different paper size to change the Paper Size setting for a tray automatically. Paper Size settings for the
    multipurpose feeder are not automatic; they must be set manually from the Paper Size menu.
    Warning—Potential Damage: Do not assign a Paper Type name that does not accurately describe the type of paper
    loaded in the tray. The temperature of the fuser varies according to the specified Paper Type. Paper may not be
    properly processed if an inaccurate Paper Type is selected.
    Assigning a Custom Type  name
    Assign a Custom Type  name to a tray to link or unlink it. Associate the same Custom Type  name to each tray
    that you want to link. Only trays with the same custom names assigned will link.
    1Make sure the printer is on and Ready appears.
    2From the control panel, press .
    3Press  repeatedly until Paper Menu appears, and then press .
    4Press  repeatedly until Paper Size/Type appears, and then press .
    5Press  repeatedly until  appears next to the name of the tray, and then press .
    The Paper Size menu appears.
    6Press  again.
    The Paper Type menu appears. Loading paper and specialty media34
    Downloaded From ManualsPrinter.com Manuals 
    						
    							7Press  repeatedly until Custom Type  or another custom name appears, and then press .
    Submitting selection appears, followed by Paper Menu.
    8Verify that the correct Paper Type is associated with the custom name.
    Note: Plain Paper is the factory default Paper Type associated with all Custom Type  names and user‑defined
    custom names.
    aFrom the Paper menu, press  repeatedly until Custom Types appears, and then press .
    bPress  repeatedly until  appears next to the custom paper type name you selected in step 7 on page 35,
    and then press 
    .
    cPress  repeatedly until  appears next to the Paper Type setting you want, and then press .
    Submitting selection appears.
    Changing a Custom Type  name
    You can use the Embedded Web Server or MarkVisionTM to define a name other than Custom Type  for each of the
    custom paper types that are loaded. When a Custom Type  name is changed, the menus display the new name
    instead of Custom Type .
    To change a Custom Type  name from the Embedded Web Server:
    1Open a Web browser.
    Note: The computer must be connected to the same network as the printer.
    2In the address bar, type the IP address of the network printer (for example,192.264.263.17).
    3Press Enter.
    4From the navigation panel of the initial page, click Configuration.
    5Click Paper Menu.
    6Click Custom Name.
    7Type a name for the paper type in a Custom Name  box.
    Note: This custom name will replace a custom type  name under the Custom Types and Paper Size/Type
    menus.
    8Click Submit.
    Submitting Selection appears.
    9Click Custom Types.
    Custom Types appears, followed by your custom name.
    10Select a Paper Type setting from the picklist next to your custom name.
    11Click Submit.
    Submitting Selection appears. Loading paper and specialty media35
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Paper and specialty media guide
    Paper guidelines
    Paper characteristics
    The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating
    new paper stock.
    Weight
    The printer can automatically feed paper weights from 60 to 220 g/m2 (16 to 58 lb bond) grain long. Paper lighter than
    60 g/m
    2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 75 g/m2 (20 lb
    bond) grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 in.), we recommend 90 g/m
    2 (24 lb) or heavier
    paper.
    Note: Duplex is supported only for 63 g/m
    2–170 g/m2 (17 lb–45 lb bond) paper.
    Curl
    Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after
    the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid,
    cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding
    problems.
    Smoothness
    Paper smoothness directly affects print quality. If paper is too rough, toner cannot fuse to it properly. If paper is too
    smooth, it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points;
    however, smoothness between 150 and 200 Sheffield points produces the best print quality.
    Moisture content
    The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly.
    Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that
    can degrade its performance.
    Condition paper before printing by storing it in its original wrapper in the same environment as the printer for 24 to
    48 hours before printing. Extend the time several days if the storage or transportation environment is very different
    from the printer environment. Thick paper may also require a longer conditioning period.
    Grain direction
    Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of
    the paper, or grain short, running the width of the paper.
    For 60 to 135 g/m
    2 (16 to 36 lb bond) paper, grain long paper is recommended. For papers heavier than 135 g/m2, grain
    short is recommended. Paper and specialty media guide36
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Fiber content
    Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the
    paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing
    fibers such as cotton can negatively affect paper handling.
    Unacceptable paper
    The following paper types are not recommended for use with the printer:
    Chemically treated papers used to make copies without carbon paper, also known as carbonless papers, carbonless
    copy paper (CCP), or no carbon required (NCR) paper
    Preprinted papers with chemicals that may contaminate the printer
    Preprinted papers that can be affected by the temperature in the printer fuser
    Preprinted papers that require a registration (the precise print location on the page) greater than ±2.3 mm (±0.9 in.),
    such as optical character recognition (OCR) forms
    In some cases, registration can be adjusted with a software application to successfully print on these forms.
    Coated papers (erasable bond), synthetic papers, thermal papers
    Rough‑edged, rough or heavily textured surface papers, or curled papers
    Recycled papers that fail EN12281:2002 (European)
    Paper weighing less than 60 g/m2 (16 lb)
    Multiple‑part forms or documents
    Selecting paper
    Using appropriate paper prevents jams and helps ensure trouble‑free printing.
    To help avoid jams and poor print quality:
    Always use new, undamaged paper.
    Before loading paper, know the recommended print side of the paper. This information is usually indicated on the
    paper package.
    Do not use paper that has been cut or trimmed by hand.
    Do not mix paper sizes, types, or weights in the same source; mixing results in jams.
    Do not use coated papers unless they are specifically designed for electrophotographic printing.
    Selecting preprinted forms and letterhead
    Use these guidelines when selecting preprinted forms and letterhead:
    Use grain long for 60 to 90 g/m2 weight paper.
    Use only forms and letterhead printed using an offset lithographic or engraved printing process.
    Avoid papers with rough or heavily textured surfaces.
    Use papers printed with heat‑resistant inks designed for use in xerographic copiers. The ink must be able to withstand
    temperatures up to 230°C (446°F) without melting or releasing hazardous emissions. Use inks that are not affected by
    the resin in toner. Inks that are oxidation‑set or oil‑based generally meet these requirements; latex inks might not.
    When in doubt, contact the paper supplier. Paper and specialty media guide37
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Preprinted papers such as letterhead must be able to withstand temperatures up to 230°C (446°F) without melting or
    releasing hazardous emissions.
    Using recycled paper
    As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for
    use in laser (electrophotographic) printers. In 1998, Lexmark presented to the US government a study demonstrating
    that recycled paper produced by major mills in the US fed as well as non-recycled paper. However, no blanket statement
    can be made that all recycled paper will feed well.
    Lexmark consistently tests its printers with recycled paper (20–100% post-consumer waste) and a variety of test paper
    from around the world, using chamber tests for different temperature and humidity conditions. Lexmark has found no
    reason to discourage the use of todays recycled office papers, but generally the following property guidelines apply
    to recycled paper.
    Low moisture content (4–5%)
    Suitable smoothness (100–200 Sheffield units)
    Suitable sheet-to-sheet coefficient of friction (0.4–0.6)
    Sufficient bending resistance in the direction of feed
    Recycled paper, paper of lower weight (
    						
    							Loading letterhead in the 520‑sheet trays
    Long‑edge orientation
    Without finisherWith finisher installed
    Short‑edge orientation
    Without finisherWith finisher installed
    Loading letterhead in the 867‑sheet tray
    Without finisherWith finisher installed
    Paper and specialty media guide39
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Loading letterhead in the 1133‑sheet tray
    Without finisherWith finisher installed
    Using transparencies
    Print samples on the transparencies being considered for use before buying large quantities.
    When printing on transparencies:
    From MarkVision Professional, Print Properties, or the control panel, set the Paper Type to Transparency.
    Feed transparencies from the standard tray or the multipurpose feeder.
    Use transparencies designed specifically for laser printers. Check with the manufacturer or vendor to ensure
    transparencies are able to withstand temperatures up to 230°C (446°F) without melting, discoloring, offsetting, or
    releasing hazardous emissions.
    Use transparencies that are 0.12–0.14 mm (4.8–5.4 mil) in thickness or 161–179 g/m2 in weight. Print quality and
    durability depend on the transparencies used.
    To prevent print quality problems, avoid getting fingerprints on the transparencies.
    Before loading transparencies, fan the stack to prevent sheets from sticking together.
    We recommend Lexmark part number 12A8240 for letter‑size transparencies.
    Using envelopes
    Print samples on the envelopes being considered for use before buying large quantities.
    When printing on envelopes:
    From the control panel, set the Paper Source based on the source in use. From MarkVision Professional, Print
    Properties, or the control panel, set the Paper Type to Envelope, and select the envelope size.
    Use envelopes designed specifically for laser printers. Check with the manufacturer or vendor to ensure the
    envelopes can withstand temperatures up to 230°C (446°F) without sealing, wrinkling, curling excessively, or
    releasing hazardous emissions.
    For the best performance, use envelopes made from 90 g/m2 (24 lb bond) paper. Use up to 105 g/m2 (28 lb bond)
    weight for envelopes as long as the cotton content is 25% or less. All‑cotton envelopes must not exceed 90 g/m
    2
    (24 lb bond) weight.
    Use only new envelopes.
    To optimize performance and minimize jams, do not use envelopes that:
    –Have excessive curl or twist
    –Are stuck together or damaged in any way Paper and specialty media guide40
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Lexmark manuals Comments (0)

    Related Manuals for Lexmark C935dtn User Manual