Home > Lexmark > Printer > Lexmark C935dtn User Manual

Lexmark C935dtn User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Lexmark C935dtn User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							11Close Door E.
    Replacing a photoconductor
    Replace the black photoconductor when 84 Replace black pc unit appears. Replace the cyan, magenta, and
    yellow photoconductors when 84 Replace color pc units appears.
    1Open Door E (front printer door).
    Warning—Potential Damage: To avoid overexposing the photoconductors, do not leave the door open for more
    than 10 minutes.
    2Release the bar by pressing the E5 button located on the bottom of the E5 latch, lift the E5 latch, and then press
    the bar down.
    Maintaining the printer141
    Downloaded From ManualsPrinter.com Manuals 
    						
    							3Remove the photoconductor(s) specified on the display.
    Photoconductor colorOpening name
    Black E1
    Cyan E2
    Magenta E3
    Yellow E4
    4Unpack the replacement photoconductor.
    5Align and insert the end of the photoconductor.
    Maintaining the printer142
    Downloaded From ManualsPrinter.com Manuals 
    						
    							6Remove the tape from the top of the photoconductor.
    7Press the button forward to insert the photoconductor while removing the casing.
    8Lift the bar up, and then press latch E5 down so that it holds the bar in position.
    Maintaining the printer143
    Downloaded From ManualsPrinter.com Manuals 
    						
    							9Close Door E.
    Replacing a toner cartridge
    Replace the specified toner cartridge (cyan, magenta, yellow, or black) when 88 Replace  toner
    appears. The printer will not continue printing until the specified cartridge is replaced.
    1Make sure the printer is on and Ready or 88 Replace  toner appears.
    2Unpack the new cartridge, and set it near the printer.
    3Open Door E (front printer door).
    4Unlock the specified cartridge by turning the cartridge counterclockwise until the arrow‑shaped handle points
    toward the unlock symbol.
    Maintaining the printer144
    Downloaded From ManualsPrinter.com Manuals 
    						
    							5Remove the cartridge by gently pulling it away from the printer.
    6Align the arrow‑shaped handle with the unlock symbol, and then insert the toner cartridge all the way into the
    opening.
    7Lock the cartridge by turning the arrow‑shaped cartridge handle clockwise until it points toward the lock symbol.
    Maintaining the printer145
    Downloaded From ManualsPrinter.com Manuals 
    						
    							8Close Door E.
    Recycling Lexmark products
    To return Lexmark products to Lexmark for recycling:
    1Visit our Web site at www.lexmark.com/recycle.
    2Find the product type you want to recycle, and then select your country from the list.
    3Follow the instructions on the computer screen.
    Moving the printer
    Before moving the printer
    CAUTION—POTENTIAL INJURY: The printer weighs 201 lb (91.2 kg); therefore, it requires at least four people or
    a properly rated mechanical handling system to lift it safely. Use the handholds on the sides of the printer to lift
    it, and make sure your fingers are not under the printer when you set it down. Disconnect all cords and cables
    from the printer before moving it.
    Maintaining the printer146
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Follow these guidelines to avoid personal injury or printer damage:
    Use at least four people or a properly rated mechanical handling system to lift the printer.
    Turn the printer off using the power switch, and then unplug the power cord from the wall outlet.
    Disconnect all cords and cables from the printer before moving it.
    Remove all printer options before moving the printer.
    Warning—Potential Damage: Damage to the printer caused by improper moving is not covered by the printer
    warranty.
    Moving the printer to another location
    The printer and options can be safely moved to another location by following these precautions:
    Any cart used to move the printer must have a surface able to support the full footprint of the printer. Any cart
    used to move the options must have a surface able to support the dimensions of the options.
    Keep the printer in an upright position.
    Avoid severe jarring movements.
    Setting the printer up in a new location
    For a basic printer, or a printer with an optional finisher installed, allow the following recommended amount of space
    around the printer:
    12 in. (50 mm)
    22.7 ft (825 mm)
    31.4 ft (418 mm)
    44 in. (100 mm)
    52.3 ft (693 mm)
    Maintaining the printer147
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Shipping the printer
    When shipping the printer, use the original packaging or call the place of purchase for a relocation kit. Maintaining the printer148
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Administrative support
    Adjusting the brightness or contrast of the display
    1Make sure the printer is on and Ready appears.
    2From the control panel, press .
    3Press  repeatedly until Settings appears, and then press .
    4Press  repeatedly until Utilities Menu appears, and then press .
    5Press  repeatedly until appears next to LCD Brightness or LCD Contrast, and then press .
    Note: Select LCD Brightness to adjust the brightness setting or LCD Contrast to adjust the contrast
    setting.
    6Press  repeatedly to decrease the setting or  repeatedly to increase the setting, and then press .
    Disabling control panel menus
    Since many people often use a printer, a support person may choose to lock the control panel menus so that the settings
    cannot be changed from the control panel.
    1Make sure the printer is turned off.
    2From the control panel, press and hold  and  while turning the printer on.
    3Release both buttons when Performing Self Test appears.
    The printer performs its power‑on sequence, and then CONFIG MENU appears.
    4Press  repeatedly until Panel Menus appears, and then press .
    5Press  repeatedly until  appears next to Disable, and then press .
    Note: Select Enable to enable the control panel menus.
    6Press  repeatedly until Exit Config Menu appears, and then press .
    The printer performs its power‑on sequence, and then Ready appears.
    Adjusting Power Saver
    1Make sure the printer is on and Ready appears.
    2From the control panel, press .
    3Press  repeatedly until Settings appears, and then press . Administrative support149
    Downloaded From ManualsPrinter.com Manuals 
    						
    							4Press  repeatedly until Setup Menu appears, and then press .
    5Press  repeatedly until Power Saver appears, and then press .
    6Press  repeatedly to decrease or  repeatedly to increase the number of minutes before the printer enters Power
    Saver mode, and then press 
    . Available settings range from 2–240 minutes.
    Note: Power Saver settings can also be adjusted by issuing a Printer Job Language (PJL) command. For more
    information, see the Technical Reference available on the Lexmark Web site at www.lexmark.com/publications.
    Restoring the factory default settings
    1From the control panel, press .
    2Press  until Settings appears, and then press .
    3Press  until Setup appears, and then press .
    4Press  until Factory Defaults appears, and then press .
    5Press  until Restore Now appears, and then press .
    Restoring Factory Defaults appears.
    Warning—Potential Damage: Restore Now returns all printer settings to the factory default settings except
    Network/Port menu settings. All downloads stored in RAM are deleted. Downloads stored in flash memory or
    on a printer hard disk are not affected.
    Encrypting the printer hard disk
    This functionality is available only when a printer hard disk is installed and working properly.
    Warning—Potential Damage: All files and resources on the printer hard disk will be deleted. Resources residing in
    the printer flash memory or RAM will not be affected.
    1Turn the printer off.
    2From the control panel, press and hold  and  while turning the printer on.
    3Release both buttons when Performing Self Test appears.
    The printer performs its power‑on sequence, and then CONFIG MENU appears.
    4Press  repeatedly until Disk Encryption appears, and then press .
    5Press  repeatedly until appears next to Enable or Disable, and then press .
    Note: Select Enable to enable hard disk encryption or Disable to disable hard disk encryption.
    Contents will be lost. Continue? appears. Administrative support150
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Lexmark manuals Comments (0)

    Related Manuals for Lexmark C935dtn User Manual