Lexmark C935dtn User Manual

							Menu itemDescription
Print Resolution
2400 IQSpecifies the printed output resolution
Note: 2400 IQ is the factory default setting.
Toner Darkness
1–5Lightens or darkens the printed output
Notes:
4 is the factory default setting.
Selecting a smaller number can help conserve toner.
If Print Mode is set to Black Only, a setting of 5 increases toner density and
darkness to all print jobs.
If Print Mode is set to Color, a setting of 5 is the same as a setting of 4.
Color Saver
On
OffReduces the amount of toner used for graphics and images. The amount of toner used
for text is not reduced.
Notes:
Off is the factory default setting.
On overrides Toner Darkness settings.
RGB Brightness
‑6–6Adjusts brightness in color outputs
Notes:
0 is the factory default setting.
‑6 is the maximum decrease. 6 is the maximum increase.
This does not affect files where CMYK color specifications are being used.
RGB Contrast
0–5Adjusts contrast in color outputs
Notes:
0 is the factory default setting.
This does not affect files where CMYK color specifications are being used.
RGB Saturation
0–5Adjusts saturation in color outputs
Notes:
0 is the factory default setting.
This does not affect files where CMYK color specifications are being used.
Color Balance
Cyan
‑5–5
Magenta
‑5–5
Yellow
‑5–5
Black
‑5–5Adjusts color in printed output by increasing or decreasing the amount of toner being
used for each color
Note: 0 is the factory default setting.
Color Balance
Reset DefaultsRestores the Color Balance factory default settings
Understanding printer menus91
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Color Samples
sRGB Display
sRGB Vivid
Display—True Black
Vivid
Off—RGB
US CMYK
Euro CMYK
Vivid CMYK
Off—CMYKPrints sample pages for each of the RGB and CMYK color conversion tables used in the
printer
Notes:
Selecting any setting prints the sample.
Color samples consist of a series of colored boxes along with the RGB or CMYK
combination that creates the color observed. These pages can be used to help
decide which combinations to use to get the desired printed output.
From a browser window, type the IP address of the printer to access a complete
list of color sample pages from the Embedded Web Server.
Manual Color
RGB Image
Vivid
sRGB Display
Display—True Black
sRGB Vivid
Off
RGB Text
Vivid
sRGB Display
Display—True Black
sRGB Vivid
Off
RGB Graphics
Vivid
sRGB Display
Display—True Black
sRGB Vivid
OffCustomizes the RGB color conversions
Notes:
sRGB Display is the factory default setting for RGB Image. This applies a color
conversion table to an output that matches the colors displayed on a computer
monitor.
sRGB Vivid is the factory default setting for RGB Text and RGB Graphics. sRGB
Vivid applies a color table that increases saturation. This is preferred for business
graphics and text.
Vivid applies a color conversion table that produces brighter, more saturated
colors.
Display—True Black applies a color conversion table that uses only black toner
for neutral gray colors.
Off turns off color conversion.
Understanding printer menus92
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Manual Color
CMYK Image
US CMYK
Euro CMYK
Vivid CMYK
Off
CMYK Text
US CMYK
Euro CMYK
Vivid CMYK
Off
CMYK Graphics
US CMYK
Euro CMYK
Vivid CMYK
OffCustomizes the CMYK color conversions
Notes:
US CMYK is the US factory default setting. US CMYK applies a color conversion
table that tries to produce output that matches SWOP color output.
Euro CMYK is the international factory default setting. Euro CMYK applies a color
conversion table that tries to produce output that matches EuroScale color
output.
Vivid CMYK increases color saturation for the US CMYK color conversion table.
Off turns off color conversion.
Enhance Fine Lines
Enables a print mode preferable for files such as architectural drawings, maps, electrical
circuit diagrams, and flow charts
Notes:
Enhance Fine Lines is not available from the control panel menus.
To set Enhance Fine Lines from the software program, with a document open,
click File > Print, and then click Properties, Preferences, Options, or Setup.
To set Enhance Fine Lines using the Embedded Web Server, type the network
printer IP address in a browser window.
Utilities menu
Menu itemDescription
Factory Defaults
Do Not Restore
RestoreReturns the printer settings to the factory default settings
Notes:
Do Not Restore is the factory default setting. Do Not Restore keeps the
user‑defined settings.
All printer settings are returned to factory default settings except Display
Language and the settings in the Parallel menu, Serial menu, Network menu,
and USB menu.
All downloads stored in RAM are deleted. Downloads stored in flash memory
or on the printer hard disk are not affected.
Understanding printer menus93
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Remove Held Jobs
Confidential
Held
Not Restored
AllRemoves confidential and held jobs from the printer hard disk
Notes:
Selecting a setting affects only print jobs that are resident in the printer.
Bookmarks, jobs on USB flash memory devices, and other types of held jobs
are not affected
Selecting Not Restored removes all Print and Hold jobs that were not restored
from the disk.
Format Flash
No
YesFormats the flash memory. Flash memory refers to the memory added by installing
a flash memory option card in the printer.
Warning—Potential Damage: Do not turn off the printer while the flash memory is
formatting.
Notes:
A flash memory option card must be installed in the printer and operating
properly for this menu item to be available.
No cancels the format request.
Selecting Yes deletes all data stored in flash memory.
Defragment Flash
No
YesPrepares the flash memory to receive new data by retrieving lost storage space
Warning—Potential Damage: Do not turn off the printer while the flash memory is
defragmenting.
Notes:
A flash memory option card must be installed in the printer and operating
properly for this menu item to be available. The flash memory option card
must not be Read/Write or Write protected.
No cancels the defragment request.
Selecting Yes reformats the flash memory after transferring all downloads to
regular printer memory. When formatting is complete, the downloads are
loaded back into flash memory.
Format Disk
No
YesFormats the printer hard disk
Notes:
A printer hard disk must be installed in the printer and operating properly for
this menu item to be available. The disk must not be Read/Write or Write
protected.
No cancels the format request.
Selecting Yes deletes all stored data and reformats the printer hard disk.
Wipe Disk (secure)
No
YesFormats the printers hard disk
Notes:
No is the factory default setting.
Selecting Yes will render all data on the hard disk unrecoverable even when
reverse engineering is attempted. This process may take up to eleven hours.
Understanding printer menus94
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Job Acct Stat
Print
ClearPrints a list of all stored job statistics or deletes the information from the printer hard
disk
Notes:
A printer hard disk must be installed in the printer and operating properly for
this menu item to be available.
Selecting Print prints a list of statistics.
Clear deletes all job statistics stored on the printer hard disk. Clearing
job account statistics appears on the display.
The Clear selection will not appear if Job Accounting is set to MarkTrackTM.
Hex Trace
ActivateAssists in isolating the source of a print job problem
Notes:
When Activate is selected, all data sent to the printer is printed in hexadecimal
and character representation and control codes are not executed.
To exit Hex Trace, turn the printer off or reset the printer.
Coverage Estimator
Off
OnProvides an estimate of the percentage coverage of cyan, magenta, yellow, and black
on a page. The estimate is printed on a separator page.
Note: Off is the factory default setting.
LCD Contrast
1–10Adjusts the contrast lighting of the display
Notes:
5 is the factory default setting.
A higher setting makes the display appear lighter.
A lower setting makes the display appear darker.
LCD Brightness
1–10Adjusts the brightness of the backlight on the display
Notes:
5 is the factory default setting.
A higher setting makes the display appear lighter.
A lower setting makes the display appear darker.
PDF menu
Menu itemDescription
Scale to Fit
Yes
NoScales page content to fit the selected paper size
Note: No is the factory default setting.
Annotations
Do Not Print
PrintPrints annotations in a PDF
Note: Do Not Print is the factory default setting.
Understanding printer menus95
Downloaded From ManualsPrinter.com Manuals 
						

							PostScript menu
Menu itemDescription
Print PS Error
On
OffPrints a page containing the PostScript error
Note: Off is the factory default setting.
Font Priority
Resident
Flash/DiskEstablishes the font search order
Notes:
Resident is the factory default setting.
A formatted flash memory option card or printer hard disk must be
installed in the printer and operating properly for this menu item to be
available.
The flash memory option or printer hard disk cannot be Read/Write,
Write, or password protected.
Job Buffer Size must not be set to 100%.
Image Smoothing
On
OffEnhances the contrast and sharpness of low‑resolution images and smooths
their color transitions
Notes:
Off is the factory default setting.
Image Smoothing has no effect on images that are 300 dpi or higher in
resolution.
PCL Emul menu
Menu itemDescription
Font Source
Resident
Disk
Flash
Download
AllSpecifies the set of fonts used by the Font Name menu item
Notes:
Resident is the factory default setting. It shows the factory default set of
fonts downloaded into RAM.
Flash and Disk settings show all fonts resident in that option.
Flash option must be properly formatted and cannot be Read/Write,
Write, or password protected.
Download shows all the fonts downloaded into RAM.
All shows all fonts available to any option.
Font Name
RO CourierIdentifies a specific font and the option where it is stored
Notes:
RO Courier is the factory default setting.
RO Courier shows the font name, font ID, and storage location in the
printer. The font source abbreviation is R for Resident, F for Flash, K for
Disk, and D for download.
Understanding printer menus96
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Symbol Set
10U PC‑8
12U PC‑850Specifies the symbol set for each font name
Notes:
10U PC‑8 is the US factory default setting.
12U PC‑850 is the international factory default setting.
A symbol set is a set of alphabetic and numeric characters, punctuation,
and special symbols. Symbol sets support the different languages or
specific programs such as math symbols for scientific text. Only the
supported symbol sets are shown.
PCL Emulation Settings
Point Size
1.00–1008.00Changes the point size for scalable typographic fonts
Notes:
12 is the factory default setting.
Point Size refers to the height of the characters in the font. One point
equals approximately 1/72 of an inch.
Point sizes can be increased or decreased in 0.25‑point increments.
PCL Emulation Settings
Pitch
0.08–100Specifies the font pitch for scalable monospaced fonts
Notes:
10 is the factory default setting.
Pitch refers to the number of fixed‑space characters per inch (cpi).
Pitch can be increased or decreased in 0.01‑cpi increments.
For nonscalable monospaced fonts, the pitch appears on the display but
cannot be changed.
PCL Emulation Settings
Orientation
Portrait
LandscapeSpecifies the orientation of text and graphics on the page
Notes:
Portrait is the factory default setting.
Portrait prints text and graphics parallel to the short edge of the page.
Landscape prints text and graphics parallel to the long edge of the page.
PCL Emulation Settings
Lines per Page
1–255
60
64Specifies the number of lines that print on each page
Notes:
60 is the US factory default setting. 64 is the international default setting.
The printer sets the amount of space between each line based on the
Lines per Page, Paper Size, and Orientation settings. Select the desired
Paper Size and Orientation before setting Lines per Page.
PCL Emulation Settings
A4 Width
198 mm
203 mmSets the printer to print on A4‑size paper
Notes:
198 mm is the factory default setting.
The 203‑mm setting sets the width of the page to allow the printing of
eighty 10‑pitch characters.
Understanding printer menus97
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
PCL Emulation Settings
Auto CR after LF
On
OffSpecifies whether the printer automatically performs a carriage return (CR) after
a line feed (LF) control command
Notes:
Off is the factory default setting.
Setting alterations are duplicated in the PPDS menu.
PCL Emulation Settings
Auto LF after CR
On
OffSpecifies whether the printer automatically performs a line feed (LF) after a
carriage return (CR) control command
Notes:
Off is the factory default setting.
Setting alterations are duplicated in the PPDS menu.
Tray Renumber
Assign MP Feeder
Off
None
0–199
Assign Tray 
Off
None
0–199
Assign Manual Paper
Off
None
0–199
Assign Man Env
Off
None
0–199Configures the printer to work with printer software or programs that use
different source assignments for trays, drawers, and feeders
Notes:
Off is the factory default setting.
None is not an available selection. It is only displayed when it is selected
by the PCL 5 interpreter.
None ignores the Select Paper Feed command.
0–199 allows a custom setting to be assigned.
Tray Renumber
View Factory Def
NoneDisplays the factory default setting assigned to each tray, drawer, or feeder
Tray Renumber
Restore Defaults
Yes
NoReturns all tray, drawer, and feeder assignments to the factory default settings
Understanding printer menus98
Downloaded From ManualsPrinter.com Manuals 
						

							PPDS menu
Menu itemDescription
Orientation
Portrait
LandscapeSets the orientation of the text and graphics on the page
Notes:
Portrait is the factory default setting.
Settings are duplicated in the PCL Emulation menu.
Lines per Page
1–255Sets the number of lines that print on each page
Notes:
64 is the factory default setting.
The printer sets the amount of space between each line based on the
Lines per Page, Paper Size, and Orientation settings. Select the desired
Paper Size and Orientation before setting Lines per Page.
Lines per Inch
0.25–30.00Sets the number of lines that print per inch
Notes:
6 is the factory default setting.
Lines per Inch can be increased or decreased in 0.25‑inch increments
Page Format
Print
WholeSets the logical and physical printable area of the page
Notes:
Print is the factory default setting. Print data maintains its position with
respect to edge of the paper.
When Whole is selected, document margins are calculated from the top
left corner of the physical edge of the page.
Printing does not occur outside the printable area.
Character Set
1
2Specifies a default character set for PPDS print jobs
Notes:
2 is the factory default setting. Character Set 2 is composed of printable
characters and symbols used in non‑US English languages.
When Characters Set 1 is selected, values given to the printer are
interpreted as printer commands.
Best Fit
On
OffReplaces a missing font with a similar font
Note: On is the factory default setting. If the requested font is not found, the
printer will use a similar font.
Tray 1 Renumber
Off
Tray 2Configures the printer to work with printer software or programs that use
different source assignments for trays, drawers, and feeders
Notes:
Off is the factory default setting.
Tray 2 is displayed only when it is installed.
Understanding printer menus99
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Auto CR after LF
On
OffSpecifies whether the printer automatically performs a carriage return (CR) after
a line feed (LF) control command
Notes:
Off is the factory default setting.
Settings are duplicated in the PCL Emulation menu.
Auto LF after CR
On
OffSpecifies whether the printer automatically performs a line feed (LF) after a
carriage return (CR) control command
Notes:
Off is the factory default setting.
Settings are duplicated in the PCL Emulation menu.
HTML menu
Menu itemDescription
Font Name
Albertus MT
Antique Olive
Apple Chancery
Arial MT
Avant Garde
Bodoni
Bookman
Chicago
Clarendon
Cooper Black
Copperplate
Coronet
Courier
Eurostile
Garamond
Geneva
Gill Sans
Goudy
Helvetica
Hoefler TextIntl CG Times
Intl Courier
Intl Univers
Joanna MT
Letter Gothic
Lubalin Gothic
Marigold
MonaLisa Recut
Monaco
New CenturySbk
New York
Optima
Oxford
Palatino
StempelGaramond
Taffy
Times
TimesNewRoman
Univers
Zapf ChancerySets the default font for HTML documents
Note: The Times font will be used in HTML documents that do not
specify a font.
Menu itemDescription
Font Size
1–255 ptSets the default font size for HTML documents
Notes:
12 pt is the factory default setting.
Font size can be increased in 1‑point increments.
Understanding printer menus100
Downloaded From ManualsPrinter.com Manuals