Lexmark C935dtn User Manual
Here you can view all the pages of manual Lexmark C935dtn User Manual. The Lexmark manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 111
Menu itemDescription Set Zone Provides a list of AppleTalk zones available on the network Note: The default setting is the default zone for the network. If no default zone exists, the zone marked with an * is the default setting. LexLink menu Menu itemDescription View Nickname Shows the assigned LexLink nickname Activate On OffActivates or deactivates LexLink support Note: On is the factory default setting. USB Direct menu Menu itemDescription USB Direct Enable DisableSpecifies whether support for the...
Page 112
Understanding printer messages List of status and error messages Activating Menu Changes Wait for the message to clear. Activating PPDS Mode The PPDS emulator has been activated. Wait for the message to clear. Bin Full Remove the stack of paper from the specified exit bin to clear the message. Busy Wait for the message to clear. Calibrating Wait for the message to clear. Cancel not available Wait for the message to clear. Canceling Wait for the message to clear. Change to Press until Continue...
Page 113
Check guides The printer cannot determine the size of the paper. Readjust the paper guides. Note: To learn how to adjust the paper guides, press repeatedly until Show Me appears, and then press . Check the tray configuration. Clearing job accounting statistics Wait for the message to clear. Close cover 1Press until Show me appears, and then press . An image of the cover appears. 2Close the specified cover to clear the message. Close door 1Press until Show me appears, and then press . An image of...
Page 114
Deleting Wait for the message to clear. Disabling DLEs Wait for the message to clear. Disabling Menus Wait for the message to clear. Note: While the menus are disabled, printer settings cannot be changed from the control panel. Disk Corrupted. Reformat? The printer attempted to recover a disk, but was not able to do so. Reformat appears. Press to reformat the disk. Note: Reformatting the disk deletes all the files currently stored on the disk. Disk recovery x/y XX% DO NOT POWER OFF Wait for the message...
Page 115
Enter PIN Enter the PIN you created in Print Properties when the confidential job was sent for printing. Enter PIN to lock Enter the PIN you created to lock the control panel and prevent menu changes. Error reading USB drive Remove the device and wait for the message to clear. The USB drive may be corrupted. Flushing buffer Wait for the message to clear. Formatting Disk x/y XX% DO NOT POWER OFF Wait for the message to clear. Warning—Potential Damage: Do not power off while the printer is formatting the...
Page 116
Internal System Error, Reload Bookmarks 1Press until Continue appears, and then press to clear the message and continue printing. 2Reload the bookmarks. Internal System Error, Reload Security Certificates Reload the security certificates. Press until Continue appears, and then press to clear the message and continue printing. Invalid Engine Code You need to download valid engine code for the printer. For information about downloading code, see the Users Guide on the Software and Documentation CD....
Page 117
Load with Load the paper tray or other source with the correct paper type and size. Note: To learn how to load the specified paper source, press repeatedly until Show Me appears, and then press . Cancel the current job. Load staples Replace the specified staple cartridge in the finisher. Note: To learn how to replace the specified staple cartridge, press repeatedly until the Show Me message for the specified staple cartridge appears, and then press . Press repeatedly until Continue appears, and...
Page 118
Power Saver The printer is saving power while it waits for the next print job. Send a job to print. Press to warm the printer to normal operating temperature. Afterwards, Ready appears. Printer locked, enter PIN to unlock The control panel is locked. Enter the correct PIN to unlock it. Printing Wait for the message to clear. Programming disk DO NOT POWER OFF Wait for the message to clear. Warning—Potential Damage: Do not turn the printer power off while Programming disk appears on the display....
Page 119
Remote Management Active DO NOT POWER OFF The printer settings are being configured. Wait for the message to clear. Warning—Potential Damage: Do not turn the printer power off while Remote Management Active appears on the display. Remove paper from all bins Output bins have reached their capacity. Remove paper from all output bins to clear the message and continue printing. Remove paper from standard bin The standard exit bin has reached its capacity. Remove paper from the standard exit bin to clear the...
Page 120
Serial The printer is using a serial cable connection. The serial port is the active communication link. Some held jobs were not restored Press until Continue appears, and then press to delete the specified job. Some held jobs will not be restored Press until Continue appears, and then press to clear the message and resume printing. Cancel the current job. Standard Bin Full Remove the stack of paper from the standard exit bin to clear the message. Staples empty or misfed Load the specified staple...