Lexmark C736 Service Manual
Have a look at the manual Lexmark C736 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information4-119 5026 Go Back Previous Next Installation notes: 1.Connect the cable (A) at the motor. 2.Slide the cable tie (B) onto the motor. 3.Insert the motor into the frame.
4-120Service Manual 5026 Go Back Previous Next 4.Replace the screws (C). 5.Slide the housing onto the motor, making sure the four tabs of the housing slide under the cable tie.
Repair information4-121 5026 Go Back Previous Next Multipurpose feeder (MPF)/duplex motor cable removal 1.Remove the multipurpose feeder/duplex motor. See “Multipurpose feeder (MPF)/duplex motor assembly removal” on page 4-118. 2.Disconnect the connector from JDX1 (A) on the system board. 3.Remove the cable from the cable retainers (B).
4-122Service Manual 5026 Go Back Previous Next Operator panel cable removal 1.Remove the top access cover assembly. See “Top access cover assembly removal” on page 4-40. 2.Remove the nine screws (A), and remove the position guide. 3.Disconnect the operator panel cable connector (B) from the operator panel card.
Repair information4-123 5026 Go Back Previous Next 4.Remove the cable from the two cable retainers (C) and routing posts (D). Installation note: Note the routing of the cable and the cable retainers.
4-124Service Manual 5026 Go Back Previous Next Operator panel ground cable assembly removal 1.Remove the top access cover assembly. See “Top access cover assembly removal” on page 4-40. 2.Remove the nine screws (A), and remove the position guide. 3.Remove the screw (B), and remove the ground cable connector. 4.Disconnect the ground cable (C). 5.Disconnect the operator panel ground cable assembly (D) and the USB connector ground cable (E). Installation note: Note the routing of the cable and the cable retainers.
Repair information4-125 5026 Go Back Previous Next Option cable removal 1.Remove the LVPS. See “Low-voltage power supply (LVPS) removal” on page 4-112. 2.Disconnect the cable connector at JOPT1 (A) on the system board. 3.Replace the rear frame cover to protect the system board. 4.Position the printer on its back. 5.Remove the two screws (B).
4-126Service Manual 5026 Go Back Previous Next 6.Press the tabs together to remove the option cable connector. Note: Be sure to note the cable routing for reinstallation.
Repair information4-127 5026 Go Back Previous Next Paper pick mechanism assembly removal See “Paper pick assembly” on page 7-5 for the part number. 1.Remove the paper tray. 2.Remove the waste toner assembly. See “Waste toner assembly removal” on page 4-174. 3.Remove the rear frame cover. See “Rear frame cover removal” on page 4-33. 4.Disconnect the connector in JFDPCK1 (A) and JTRAY1 (B) on the system board. 5.Push the cables through the hole in the frame (C). 6.Open the front access cover.
4-128Service Manual 5026 Go Back Previous Next 7.Remove the transfer module with the photoconductor units attached. a.Disconnect the transfer module cable (D). b.Press the two tabs (E) to release the front access cover assembly, and lower the front access door cover. c.Press the two tabs (F) on either side of the transfer module, and lift out the transfer module. Note: Leave the photoconductor units on the transport belt when removing. Warning: To avoid damaging the photoconductor drum, place the transfer module with the photoconductor units on a clean surface. Never expose the photoconductor units to light for a prolonged period of time. Place a clean, dry cloth over the transfer module and photoconductor units until they are required. 8.Remove the toner cartridges.