Land Rover Defender V8i Workshop Supplement Rover Manual
Have a look at the manual Land Rover Defender V8i Workshop Supplement Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
04GENERAL SPECIFICATION DATA 10 INFORMATION ELECTRICAL System 12 volt, negative ground............................................................................. Battery Make Land Rover Parts and Equipment................................................................................ Lucas maintenance free Type - standard 9-plate 371....................................................... Type - heavy duty 13-plate 389.................................................... Generator Manufacturer Magnetti Marelli.................................................................... Type A127 - 100amp................................................................................. Polarity Negative ground............................................................................. Brush length: New 17 mm......................................................................... 0.67 in Worn, minimum free protrusion from moulding 5 mm....... 0.20 in Brush spring pressure flush with moulding 1.3 to 2.7N...................... 0.25 to 0.60 lbf Regulator voltage 13.6 to 14.4 volts............................................................. Nominal output: Generator speed 6000 rev/min..................................................... Control at 14 V 65 A........................................................ Starter motor Make and type Magnetti Marelli M78R pre-engaged................................................................. Brush spring tension 1020 gf........................................................ 16 ozf Brush minimum length 9.5 mm..................................................... 0.37 in Fuses Type Autofuse (blade type)................................................................................. Blow ratings to suit individual circuits Horns Make/type Klamix (Mixo) TR99........................................................................
GENERAL SPECIFICATION DATA 11 INFORMATION BULBS Exterior Type Headlamps 12V -60/55W Halogen....................................................................... Side lamps 12V -5W bayonet capless....................................................................... Side marker lamps 12V -3.5W capless........................................................... Tail/Stop lamps 12V -5W/21W bayonet................................................................ Stop lamps 12V -21W bayonet....................................................................... High level stop lamp 12V -21W bayonet......................................................... Direction indicator lamps 12V -21W bayonet.................................................. Number plate lamp 12V -5W capless........................................................... Reverse lamp 12V -21W bayonet................................................................... Rear fog guard lamp 12V -21W bayonet........................................................ Interior Type Interior roof lamps 12V -10W festoon............................................................ Instrument illumination 12V -1.2W capless..................................................... Warning light panel 12V -1.2W bulb/holder unit.......................................................... Hazard warning switch 12V -1.2W capless..................................................... CAUTION: The fitting of new bulbs with wattages in excess of those specified will result in damage to vehicle wiring and switches.
04GENERAL SPECIFICATION DATA 12 INFORMATION VEHICLE WEIGHTS AND PAYLOAD When loading a vehicle to its maximum Gross Vehicle Weight (GVW), consideration must be taken of the unladen vehicle weight and the distribution of the payload to ensure that axle loadings do not exceed the permitted maximum values. It is the customers responsibility to limit the vehicles payload in an appropriate manner such that neither maximum axle loads nor GVW are exceeded. VEHICLE KERB WEIGHTS Kerb weight = Vehicle weight + Full fuel tank (no occupants or pay load) Hard top 1770 kg........................................................................... 3902 lb Gross vehicle weight 2720 kg........................................................ 6001 lb VEHICLE GROSS AXLE WEIGHTS Front axle (GAWF) 1225 kg........................................................... 2701 lb Rear axle (GAWR) 1495 kg........................................................... 3300 lb NOTE: Axle weights are not additive. The individual maximum axle weights and gross vehicle weight must not be exceeded. TOWING WEIGHTS On-road Off-road Unbraked trailers 750 kg, 1653 lb.............................................................. 500 kg, 1102 lb Trailers with overrun brakes 3500 kg, 8818 lb............................................. 1000 kg, 2204 lb 4 wheel trailers with coupled brakes * 4000 kg, 8818 lb.............................. 1000 kg, 2204 lb Nose weight 160 kg, 350 lb..................................................................... 160 kg, 350 lb NOTE: * Only applies to vehicles modified to accept coupled brakes. NOTE: All weight figures are subject to local restrictions.
GENERAL SPECIFICATION DATA 13 INFORMATION OFF-ROAD PERFORMANCE Kerb weight, full fuel tank and 75 kg, 150 lb: Max. gradient 45° ................................................................... Approach angle 51° ................................................................ Departure angle 35° ............................................................... Wading depth 500 mm................................................................... 20 in Min. ground clearance (unladen): 229 mm.................................... 9.0 in Ramp break over angle 146° .................................................... NOTE: Departure angles do not account for the addition of a tow hitch.
04GENERAL SPECIFICATION DATA 14 INFORMATION WHEELS AND TYRES Wheel size - Alloy 7J X 16............................................................. Tyre size 265/75 - R16 MULTI-TERRAIN.......................................................................... Tyre pressures: Front Rear Normal - all load conditions 265/75 R16 All Terrain.............................................. Front 1,9 bar................................ 28 lbf/in 2 Rear 2,4 bar................................. 35 lbf/in2 Soft ride* Front 1.6 bar................................ 23 lbf/in2 Rear 2,1 bar................................. 30 lbf/in2 * Soft ride pressure is for limited use only and MUST NOT be used above 55 mph, 85 km/h. WARNING: Tyre pressures must be checked with the tyres cold, as the pressure is about 0.2 bar, 3 lbf/in2higher at running temperature. If the vehicle has been parked in the sun or high ambient temperatures, DO NOT reduce the tyre pressures, move the vehicle into the shade and wait for the tyres to cool before checking the pressures. WARNING: Always use the same make and type of radial-ply tyres, front and rear. DO NOT use cross-ply tyres, or interchange tyres from front to rear. If the wheel is marked TUBELESS, an inner tube must NOT be fitted. VEHICLE DIMENSIONS Overall length (including spare wheel) 4072 mm............................. 160.5 in Overall width (excluding mirrors) 1790 mm...................................... 70.5 in Overall height 2037 mm................................................................... 80.2 in Wheelbase 2360 mm....................................................................... 92.9 in Track front/rear 1486 mm................................................................. 58.5 in Interior width between wheel boxes 925 mm................................. 36.4 in Turning circle 12.65m.................................................................... 41ft 6in
05 - ENGINE TUNING DATA CONTENTS Page INFORMATION ENGINE 4.0 V8i 1...................................................................................................
ENGINE TUNING DATA 1 INFORMATION ENGINE 4.0 V8i Type4.0 Litre V8i ................................................................................. Firing order1-8-4-3-6-5-7-2 ..................................................................... Cylinder Numbers Left bank 1-3-5-7.......................................................................... Right bank 2-4-6-8........................................................................ No 1 Cylinder locationPulley end of left bank ................................................... Spark plugs Make/type Champion RN11YCC........................................................................ Gap 0.90 - 1.00 mm.................................................................................. 0.035 - 0.040 in Coils Make Lucas 2D1S2................................................................................ Type Double ended coil, bank of 4................................................................................. Compression ratio 9.35:1 - High Compression............................................................ Fuel injection system Make Sagem - Lucas................................................................................ Type GEMS Sequential Multipoint Fuel injection (SFi)................................................................................. Hot-wire air flow sensor system electronically controlled Valve Timing Inlet Exhaust Opens 28°BTDC .............................................................................. 66°BBDC Closes 77°ABDC .............................................................................. 39°ATDC Duration 285° ........................................................................... 285° Valve peak 108°ATDC ....................................................................... 110°BTDC Idle speed - controlled by GEMS system All loads off 700±20 rev/min .............................................................. Base idle speed Not adjustable............................................................... Idle air control valve position Checked viaTestBook ................................... CO at idle Less than 0.5%......................................................................... Fuel Fuel grade 95 RON minimum - unleaded........................................................................
07 - GENERAL FITTING REMINDERS CONTENTS Page INFORMATION GENERAL FITTING REMINDERS 1....................................................................... PRECAUTIONS AGAINST DAMAGE 1.................................................................. SAFETY PRECAUTIONS 1.................................................................................... PREPARATION 2.................................................................................................... DISMANTLING 2..................................................................................................... INSPECTION-GENERAL 2..................................................................................... BALL AND ROLLER BEARINGS 3......................................................................... OIL SEALS 4........................................................................................................... JOINTS AND JOINT FACES 5................................................................................ FLEXIBLE HYDRAULIC PIPES, HOSES 5............................................................. FUEL SYSTEM HOSES 6....................................................................................... METRIC BOLT IDENTIFICATION 6........................................................................ METRIC NUT IDENTIFICATION 6.......................................................................... KEYS AND KEYWAYS 6........................................................................................ TAB WASHERS 6................................................................................................... SPLIT PINS 7.......................................................................................................... NUTS7 ................................................................................................................... LOCKING WIRE 7................................................................................................... SCREW THREADS 7.............................................................................................. UNIFIED THREAD IDENTIFICATION 8..................................................................