Land Rover Body And Paint Air Bag And Safety Belt Rover Manual

Failure Mode
In the event of a failure of the AFS system, a warning
indicator in the instrument cluster is illuminated to warn
the driver. The AFS warning indicator illuminates when
the ignition switch is in the ignition position (II) and
will illuminate continuously until the fault is rectified.
The AFS warning indicator will also be illuminated if
a failure of the steering angle sensor or the vehicle speed
signal is detected.
Illumination of the AFS warning indicator does not
necessarily mean that...

AUTOMATIC HEADLAMP
OPERATION
The automatic headlamp function is a driver assistance
system. The driver can override the system operation
by selection of side lamp or headlamp on if the ambient
light conditions require front and rear lighting to be
active. The automatic headlamp system uses a light
sensor and the CJB, which are connected via the LIN
bus to control the headlamp functionality.
A light sensor is incorporated in the rain/light sensor
located on the inside of the windshield, below the rear...

Vehicle headlamp levelling is performed by the air
suspension system and the air suspension control
module. The suspension system constantly monitors the
vehicle attitude and adjusts the height of the front and/or
rear of the vehicle accordingly. This maintains the
correct vehicle attitude and consequently maintains the
correct headlamp beam alignment.
The vehicle levelling system is fully automatic, therefore
the lighting control switch does not have the manual
levelling rotary control.
Dynamic Headlamp...

Front fog lamps are an optional fitment on low
specification vehicles and a standard fitment on high
specification vehicles.
Two front fog lamps are located in apertures in the front
bumper. Each lamp is secured in the bumper with three
screws which are covered with a finisher. The fog lamp
has an adjuster screw which is accessible by removal
of the lamp surround and is used to set the fog lamp to
the correct alignment.
The fog lamp uses a 55W halogen H11 bulb which is
located in a holder. The holder is...

The rear lamp assembly is a one piece unit which
contains a stop/tail lamp, a turn signal lamp, a second
tail lamp, a reversing lamp and a fog lamp. Five bayonet
fitting bulbs are used (six on NAS vehicles with the
addition of a side marker lamp). These are located in
holders which fit into the applicable hole in the lamp
housing and are locked by rotating. Each bulb holder is
connected by wires to a connector on the rear of the
lamp housing.
The rear lamp assembly is located in a recess in the
vehicle...

lamp or headlamp position, the lighting control switch
can be pulled to the second position (if front fog lamps
fitted) to activate the front fog lamps. If front fog lamps
are not fitted, the switch need only be pulled to the first
position. A rear fog lamp warning indicator is
illuminated in the instrument cluster when the rear fog
lamps are active.
SIDE REPEATER LAMP
Side repeater1
Bulb holder2
Clip3
The side turn signal lamps are located in the driver and
passenger doors, below each door mirror. The...

HAZARD FLASHERS
The hazard flashers are controlled by a non-latching
switch in the centre of the instrument panel. The hazard
flashers operate at all times when selected and are not
dependant on ignition switch position.
When the hazard flashers are selected on, all of the front,
rear and side turn signal lamps operate as previously
described and both left and right turn signal indicators
in the instrument cluster also flash. The hazard warning
flashers flash at a rate of 380ms on and 380ms off. When
the...

HIGH MOUNTED STOP LAMP
High mounted stop lamp1
Housing2
The high mounted stop lamp is located in the upper
tailgate. The stop lamp housing also provides location
for the tail door window washer jet.
The lamp comprises a plastic housing with a red
coloured lens. The lamp is illuminated by a number of
Light Emitting Diodes (LEDs).
The high mounted stop lamp is activated, along with
the tail lamp stop lamps, when the ignition switch is in
the ignition position (II) and the brake pedal switch is
active (by...

Possible CauseCustomer SymptomDTC Symptom Description
Open circuit or short circuit to
earth
Swivelling does not functionLH or RH AFS actuator -
Communication failure
Open circuit or short circuit to
earth
Swivelling does not functionLH or RH AFS Actuator failure
Open circuit or short circuit to
earth or 12V
Levelling does not functionLH or RH Levelling Motor
Failure
Open circuit or short circuit to
earth or 12V
Swivelling and levelling do not
function. Other vehicle system
functions perhaps also...

CONTROL DIAGRAM
Hazard warning lamps switch1Ignition relay2
Exterior LightingLesson 2 – Electrical
191Technical Training (G421288)