Land Rover Body And Paint Air Bag And Safety Belt Rover Manual

When the ambient temperature is being displayed, if the
temperature falls to 4ºC (39.2ºF) or below, the cold
warning symbol will display. The cold warning symbol
is in the form of a snow flake and will flash on and off,
five times at a frequency of 2Hz. An audible warning
will also be emitted by the instrument cluster to alert
the driver. After the fifth flash of the symbol, the display
will continue to display the snow flake symbol in place
of EXT until a temperature of 6°C (42.8°F) or higher
is...

in the EEPROM, therefore, if the battery is disconnected,
the trip data will be lost and the display will show 000.0
when the battery is reconnected.
Gear Position Indicator
Automatic Transmission
The gear position indicator shows the current selector
lever position on vehicles with automatic transmission.
During normal operation the display will show P for
Park, R for reverse, N for Neutral and D for Drive.
When the transmission is operated in CommandShift™
mode, the display shows the currently selected...

uses these two values to calculate the distance remaining
to the next service. The remaining distance value is used
to display the oil service requirement.
The mileage is displayed to the nearest 50 Km or 25
miles depending on the market configuration of the
vehicle. If the service interval passes zero without being
reset, the instrument pack will continue counting down
and the remaining distance display will show a negative
(-) value.
The trigger point for displaying the remaining distance
is 2500 Km or...

G.If the oil service value is to be reset, press the trip
reset button within 10 seconds of releasing it and
hold for more than 5 seconds. The information
display will show RESET for 5 seconds and then
reset the oil service value.
•If reset is not possible, the information display
will show CANNOT RESET for 5 seconds.
H.The information display will show INSPECT.
I.If the inspection service value reset is not required,
press the trip reset button within 10 seconds of
releasing it in step G and hold for...

NOTE: The factory default settings may differ between
market configuration of the vehicle.
The customer settings system is controlled by CAN bus
message inputs and outputs from the instrument cluster,
the Central Junction Box (CJB), the ABS Module and
the Integrated Head Unit (IHU). The following table
details the modules and their associated function within
the settings system.
Output InformationModule
Remote handset identityCentral Junction
Box (CJB)Ignition key position
Vehicle movingABS Module...

menu and allows the driver to select a delay period or
disable the pre-heat function. If OFF is not selected, the
next press of the radio search button >>| displays the
pre-heat on time hour menu and a further press of the
radio search button >>| displays the pre-heat on time
minutes menu.
CABIN PRE-HEAT
The CABIN PRE-HEAT menu allows the driver to
select the pre-heat settings:
•OFF (default)
•30 Mins
If OFF is selected, when the radio search button >>| is
pressed, the settings menu will display the next...

time minutes which are displayed in increments of 15
minutes between 0 and 60 minutes. The default for the
minutes is 0. The value is changed by pressing the + or
- buttons on the steering wheel. If the button is pressed
and held for more than 4 seconds, the time increments
at one hour per second for as long as the button is
pressed.
TRIP DISTANCE UNITS
The TRIP DISTANCE UNITS menu allows the driver
to adjust the units in which the trip distance is displayed
in the trip computer display. The units can be...

LAZY ENTRY (if memory module fitted)
The LAZY ENTRY menu allows the driver to disable
or enable the lazy entry function which moves the
exterior door mirror and the seat position to that set by
the driver. The memory positions are stored in the
memory module and the individual settings are
recognised from the ignition key identification. The
feature can be changed to on or off using the steering
wheel + or - buttons.
The menu allows the driver to select the following:
•OFF (default)
•ON
RESTORE FACTORY...

TRIP COMPUTER
General
The high line instrument cluster contains software which
enables the use of an on-board trip computer. The
computer allows the driver to access information for
current fuel usage, current journey length, average speed
and estimated distance on fuel remaining. The
information is displayed in the lower part of the message
center, providing no other high priority messages are
being displayed. If no messages are being displayed or
the displayed message is of a low priority, the trip...

•Pressing the trip computer button for more than
2 seconds will reset the average speed. The
display will show dashes for 3 seconds and then
change to zeros.
•Pressing the trip computer button for less than 2
seconds will change the display to the next
feature.
•Overspeed Warning
•The overspeed warning is only displayed if
enabled in the customer settings.
•Pressing the trip computer button for more than
2 seconds will turn the overspeed warning off. A
second press of the trip computer button for more...