Kyocera TASKalfa 221 User Manual

Copier Functions1-13
Border Erase Mode
Shadows that may appear around the edges of copies can be erased.
The following modes are availabl e for border erase function.
NoteYou can set the default value of the border erase width. (See  Border Erase Width Default Value 
on page 3-10.)
1Set the original.
2Press the  Border Erase  key.
3Press the S key or the T  key to select Sheet Erase  
or  Book Erase.
4Press the  Enter key.
5Press the  < key or the  > key to set the border erase 
width. You can set the...

Copier Functions
1-14
Continuous Copying
The continuous copying function allows multiple originals to be separated into some blocks, to be 
scanned at more than one time, and to be copied in one batch. Since multiple originals of the same 
type are scanned in multiple steps to accumulate data in memory, many originals can be copied in 
one batch.
1Set the originals.
2Press the  Function key.
3Press the  S key or the  T key to select  Continuous 
scan .
4Press the  Enter key.
5Press the  S key or the  T...

Copier Functions1-15
Auto Rotation
With the auto rotation function, t he image of the original is automatically rotated counterclockwise by 
90 degrees if the orientation of the original is diff erent from that of the paper loaded in the cassette.
Notes• The paper sizes that can be used for auto rotation are A4/11 × 81/2 or smaller sizes. A3, B4, 
Folio, 11 × 17 (Ledger), 8
1/2× 14 (Legal) or 8K cannot be used for auto rotation.
• You can select whether or not to enable auto rotation at a default...

Copier Functions
1-16
EcoPrint Mode
The ecoprint mode can reduce toner consumption. Use this mode when high quality copies are not 
necessary, for example, for trial copying.
Notes• The copy densityDensity will be a little lighter.
• You can select whether or not to turn on  the ecoprint mode at a default setting. (See EcoPrint 
Mode  on page 3-4.)
1Set the original.
2Press the  Function key.
3Press the  S key or the  T key to select  EcoPrint.
4Press the Enter key.
5Press the  S key or the  T key to...

Copier Functions
1-17
Mixed Size Originals Mode
With  Mixed Size Originals, you  need not use the Paper Selection key to specify the paper size 
when  using  the opti onal document  processor. T he origi nal sizes  are detected  one by one and ea ch 
origi nal is automatical ly copied to a sheet of the same size.
Notes•The maximum numb er of sheets that can be set in  the do cument  processor in  this mode  is 30.
• The origin al sizes th at can be  used for the auto se lection mode:
Inch Specification...

Copier Functions
1-18
Program Function
Up to eight combinations of copy modes and functions displayed on the operation panel can be 
registered as a single program.
Registering a Program
1Set the desired copy modes, etc., to be registered.
2Press the  Program key.
3Press the  S key or the  T key to select  Register 
program .
4Press the  Enter key.
5Press the  S key or the  T key to select the program 
number to register (1 to 8).
NoteYou can also select the program number using a numeric key.
6Press the...

2-1
2 Printer Settings
This chapter explains the settings required for using the printer functions. For setting operation 
required for using this machine as a network printer, use the operation panel.
The principal settings that can be made are shown below.
• Using This Machine as a Network Printer
• Menu Hierarchical Diagram
• Status Page Printing
• e-MPS Function
• Interface
•Emulation
• Font
• Print Configuration
• Print Quality
• Memory Card Operation
• Hard Disk Operation
• RAM Disk Operation
•...

Printer Settings
2-2
Using This Machine as a Network Printer
To use this machine as a network printer, use the procedure below for the setting.Preparation of network connection environment(Assignment of IP address, etc.)
È
Connection of network cable
(Refer to the  Basic Operation Guide , Connecting the Network Cable.)
È
Setting operation from the operation pane l of this machine (See this chapter.)
Principal setting items
•Network
• Emulation selection
• Number of copies and print orientation
• Print...

Printer Settings2-3
Menu Hierarchical Diagram
Note> displayed on each setting screen indicates the current setting.
Print Status 
Page `No
, Print
e-MPS `Quick Copy `Select User 
Name`Select JOB
`Copies: ###
Delete
Private/
Stored `Select User 
Name`Select JOB
`Copies: ### Enter User ID
Delete
Print VMB 
Data `Tray ### Enter User ID
List of VMB `No,  Print
List of code 
JOB `No, 
Print
e-MPS 
Configuration `Quick Copy
`Number of JOB:  0 to  50
Temp Code Job 
Size `0
 to  9999 M Byte
Perm Code Job 
Size...

Printer Settings
2-4
Emulation`PCL 6
KC-GL `KC-GL Pen 
Adjust `Pen (1
 to 8) `01 to  99 dot(s)
KC-GL Page 
Set `A2, A1, 
A0, B3,  B2, B1,  B0, SPSZ
KPDL `Print KPDL 
Errs `On, Off
KPDL (AUTO) `Print KPDL 
Errs `On, Off
Alt. 
Emulation `PCL6
, KC-GL , Line Printer , IBM Proprinter , 
Diablo 630 , EPSON LQ-850
Line Printer
IBM Proprinter
Diablo 630
EPSON LQ-850
Font `Select Font `Internal `I### ID `I###
Detail `4 to  999.75 Point
0.44 to  99.99 CPI
Courier `Dark,  Regular
Letter 
Gothic `Dark, 
Regular...