Kyocera KM 1650 User Manual

Job Accounting 
ADVANCED OPERATION GUIDE 4-15
Using Job Accounting
Copy Operation
To perform copying operations when Job Accounting is enabled, enter 
your ID-code using the numeric keys.
1Enter the ID-code using the 
numeric keys and press [Enter].
The Copier Basic screen displays.
NOTE: If you enter an incorrect code, press [Stop/Clear] and enter the 
code again.
If the entered ID-code does not match any registered ID-code, an error 
sound is emitted. Enter the correct ID-code and press [Enter]....

Job Accounting 
4-16 ADVANCED OPERATION GUIDE
Downloaded From ManualsPrinter.com Manuals 

ADVANCED OPERATION GUIDE Appendix-1
Appendix
The Appendix contains the following specifications:
• Paper ............................................................... Appendix-2
• Specifications .................................................Appendix-11
• Glossary ........................................................ Appendix-17
Downloaded From ManualsPrinter.com Manuals 

Appendix 
Appendix-2 ADVANCED OPERATION GUIDE
Paper
General Guidelines
The machine is designed to print on standard copier paper (the type used 
in ordinary dry copier machines), but it can also accept a variety of other 
types of paper within the limits specified below.
NOTE: The manufacturer assumes no liability for problems that occur 
when paper not satisfying these requirements is used.
Selection of the right paper is important. Using the wrong paper can result 
in paper jams, curling, poor print...

Appendix 
ADVANCED OPERATION GUIDE Appendix-3
Selecting the Right Paper
This section describes the guidelines for selecting paper.
Condition
Avoid using paper that is bent at the edges, curled, dirty, torn, embossed, 
or contaminated with lint, clay, or paper shreds.
Use of paper in these conditions can lead to illegible printing and paper 
jams, and can shorten the life of the machine. In particular, avoid using 
paper with a surface coating or other surface treatment. Paper should have 
as smooth and...

Appendix 
Appendix-4 ADVANCED OPERATION GUIDE
Smoothness
The paper should have a smooth, uncoated surface. Paper with a rough or 
sandy surface can cause voids in the printed output. Paper that is too 
smooth can cause multiple feeding and fogging problems. (Fogging is a 
gray background effect.)
Basis weight
Basis weight is the weight of paper expressed in grams per square meter 
(g/m²). Paper that is too heavy or too light may cause feed errors or paper 
jams as well as premature wear of the product....

Appendix 
ADVANCED OPERATION GUIDE Appendix-5The moisture content of the paper varies with the relative humidity in the 
room. When the relative humidity is high and the paper absorbs moisture, 
the paper edges expand, becoming wavy in appearance. When the relative 
humidity is low and the paper loses moisture, the edges shrink and tighten, 
and print contrast may suffer.
Wavy or tight edges can cause jams and alignment anomalies. The 
moisture content of the paper should be 4 to 6 %.
To ensure correct...

Appendix 
Appendix-6 ADVANCED OPERATION GUIDEPackaging: Paper should be packed in a sturdy carton to protect it from 
damage during transport. Quality paper obtained from a reputable supplier 
is usually correctly packaged.
Special treatment: It is recommended not to use paper with the following 
treatment even if the paper satisfies the basic specifications. To use this 
type of paper, perform a test prior to purchasing large amounts.
- Glazed paper
- Watermarked paper
- Paper with uneven surface
-...

Appendix 
ADVANCED OPERATION GUIDE Appendix-7Since the composition and quality of special paper vary considerably, 
special paper is more likely than white bond paper to give trouble during 
printing. No liability will be assumed if moisture and so forth given off during 
printing on special paper causes harm to the machine or operator.
NOTE: Before purchasing any type of special paper, test a sample on the 
machine and check that printing quality is satisfactory.
Transparency
Transparency must be able...

Appendix 
Appendix-8 ADVANCED OPERATION GUIDESome label paper is manufactured with an extra margin of top sheet 
around the edge. Do not remove the extra top sheet from the carrier sheet 
until after printing is finished.
The table below lists the specifications for adhesive label paper.
Postcards
Fan the stack of postcards and 
align the edges before loading 
them in the MP tray. Make sure 
the postcards you are going to set 
are not curled. Feeding curled 
postcards may cause paper jams.
Some postcards...