Kyocera FS C5250DN User Manual

4-33Using the Operation Panel
Entering the Width and Length
Enter the paper size for 
X Dimension and Y Dimension  as shown in 
the figure. 
1When the unit of measurement is set, press  V. 
>>X Dimension  appears (the paper width setting).
2Press [OK]. A blinking cursor ( _) appears.
3Press  U or  V to increase or decrease the value of the figure where 
the cursor is blinking and display the desired width. 
Acceptable paper widths are as follows:
• Cassette : 105 to 216 mm (4.13 to 8.5 inches)
• Paper...

Using the Operation Panel
4-34
If optional paper feeders are added,  Cassette 1 Type will appear 
for the standard paper cassette and Cassette 2 Type , Cassette 
3 Type , and Cassette 4 Type  will appear for the optional paper 
feeders.
3To change paper type, press  [OK]. A blinking question mark ( ?) 
appears.
4Press  U or V  to display the desired paper type. The message display 
toggles through the following paper types:
PLAIN
PREPRINTED
LABELS
BOND
RECYCLED
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
ENVELOPE...

4-35Using the Operation Panel
4Press 
U or V  to display the desired paper type. The display changes 
as shown below.
PLAIN
TRANSPARENCY
PREPRINTED
LABELS
BOND
RECYCLED
VELLUM
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
ENVELOPE
CARDSTOCK
COATED
THICK
HIGH QUALITY
CUSTOM 1  (to 8)
5Press  [OK].
6Press Z and proceed to the next step  Paper Weight (Setting the 
paper weight) .
Paper Weight (Setting the paper weight)
You can set the paper thickness for your custom paper type to be 
customized.The default setting is...

Using the Operation Panel
4-36
3Press  [OK]. A blinking question mark ( ?) appears.
4Select  Enable  or Disable  using U or  V. For details of the default 
setting for each paper type, refer to  Paper Specifications on page 3-2. 
5Press [OK].
6Press [MENU] . The display returns to Ready .
The custom paper type setting is completed.
Reset Type Adjust (Resetting the custom paper type)
Reset all the custom paper type that was set in  Type Adjust (Creating 
custom paper type) on page 4-34 .
1Press Z while...

4-37Using the Operation Panel
Print Settings
These settings specify printing parameters such as the print quality used 
for printing (Normal or Fine), the gl
oss mode (Low or High), the number 
of copies, reduced printing and the page orientation. 
The options available in Print Settings are as follows:
• Paper Source (Selecting the paper feed source)
• Paper Feed Mode (Setting the paper feed source)
• Duplex (Duplex printing)
• Override A4/LT (Overriding difference between A4 and Letter)
• Emulation...

Using the Operation Panel
4-38
Paper Feed Mode (Setting the paper feed source)
This mode specifies how the paper should be fed once the paper feed 
source and paper type have been chosen. If  Auto is selected, the printer 
searches for a paper feed source that matches the paper size and type, 
and paper is then delivered from that source. If  Fixed is selected and 
there is no matching paper feed source, handling proceeds as specified 
by  Paper Mismatch  for Error Handling . For details on paper...

4-39Using the Operation Panel
Activating the duplexer is done by selecting either short edge or long 
edge binding mode.
IMPORTANT  
Duplex printing for coated paper (COATED) is possible 
if the optional paper feeder PF-530 is installed.
Binding Modes
Binding refers to the manner in which printed pages of paper are joined 
together (by gluing, stitching, etc.) in book form. The two possible types 
of binding are: long-edge binding, in which pages are joined together 
along their long edge; and short-edge...

Using the Operation Panel
4-40
Override A4/LT (Overriding difference between A4 and 
Letter)
When the  Override A4/LT  is turned On using the operation panel, the 
printer ignores the difference between A4 and Letter paper sizes. Printing 
is performed without an error message even if the actual paper size in the 
current cassette differs from the paper size formatting the job.
By default, this feature is  Off.
1Press  Z while Print Settings >  is displayed.
2Press U or  V repeatedly until  >Override...

4-41Using the Operation Panel
3Press
 [OK]. A blinking question mark ( ?) appears.
4Select  KPDL or KPDL (AUTO)  using U or V. Press  [OK].
5Press  Z. >>Error Report  appears.
6Press [OK]. A blinking question mark ( ?) appears.
7Select  On or  Off using  U or  V. Press  [OK].
8Press  [MENU] . The display returns to Ready .
>Emulation
? PCL 6
>Emulation>
?KPDL(AUTO)
>>Error Report
? On
Downloaded From ManualsPrinter.com Manuals 

Using the Operation Panel
4-42
Color Mode (Selecting color or Black & White printing)
You can use the Color Mode menu on the operation panel to select the 
Black & White or Color printing mode. By default, the printer is set to print 
in color mode.
1Press  Z while Print Settings >  is displayed.
2Press U or  V repeatedly until  >Color Mode appears.
3Press [OK]. A blinking question mark ( ?) appears.
4Press  U or V  to change color mode —  Color or Black & White .
5When the desired color mode is...