Kyocera FS 2000D User Manual

							2F8/2F9/2GA-2
1-5-29 5. Remove the eight screws and three ground-
ing terminals.
Figure 1-5-39
6. Remove the AC inlet.
7. Remove the one connector.
8. Remove the PWB connector between con-
nect-L PWB and then remove the power 
source unit.
9. Remove the power source unit.
10. Check or replace the power source unit and 
refit all the removed parts.
Figure 1-5-40
Screw
Screw
Screw
Screw ScrewScrew Screw Screw
Grounding
terminal Grounding
terminal Grounding
terminal
PWB connector
Connect-L PWB
Connector
Power source unit
AC inlet
Downloaded From ManualsPrinter.com Manuals 
						

							2F8/2F9/2GA-2
1-5-30
1-5-9  Others
(1) Detaching and refitting the paper feed drive unit
Procedure
1. Remove the paper cassette.
2. Remove the developer unit (See page P.1-5-
9).
3. Remove the top cover (See page P.1-5-2).
4. Remove the right cover (See page P.1-5-3).
5. Remove the five connectors from the con-
nect-R PWB.
6. Remove wires from the clamp.
7. While opening the four hooks and then 
remove the wires.
8. Remove the right fan motor.
Figure 1-5-41
9. Remove the three screws and then remove 
the paper feed drive unit.
10. Check or replace the paper feed drive unit 
and refit all the removed parts.
To refit the paper feed drive unit, make sure 
mesh of gears.
Figure 1-5-42
Right fan motor
Connect-R PWB Hook
Hook Clamp
Hook
HookConnectors
(five)
Gear
Gear
Screw ScrewScrewPaper feed
drive unit
Paper feed
drive unit
Downloaded From ManualsPrinter.com Manuals 
						

							2F8/2F9/2GA
1-5-31 (2) Detaching and refitting the main drive unit
Procedure
1. Remove the top cover (See page P.1-5-2).
2. Remove the right cover (See page P.1-5-3).
3. Remove the controller box (See page P.1-5-
26).
4. Remove five screws and then remove the 
main drive unit.
5. Check or replace the main drive unit and 
refit all the removed parts.
Figure 1-5-43
Screw
ScrewScrew
Screw
ScrewMain drive unit
Downloaded From ManualsPrinter.com Manuals 
						

							2F8/2F9/2GA-1
1-5-32 (3) Detaching and refitting the laser scanner unit
Procedure
1. Remove the top cover (See page P.1-5-2).
2. Remove the right cover (See page P.1-5-3).
3. Remove the three/four connectors from the 
main PWB.
4. Remove the four screws and then remove 
the laser scanner unit.
5. Check or replace the laser scanner unit and 
refit all the removed parts.
Figure 1-5-44
Screw
Screw
Laser scanner unit
Connectors (three/four)
45/47 ppm printer
(EUR/USA model)
only Screw Screw
45/47 ppm printer
(EUR/USA model)
only
Downloaded From ManualsPrinter.com Manuals 
						

							2F8/2F9/2GA-1
1-6-1
1-6 Firmware1-6-1  Downloading firmware
The system firmware can be update by downloading new firmware. Downloading can be made either by directly sending 
the new firmware from PC via the parallel interface or using a memory card that contains the new firmware.
Figure 1-6-1
S2F8_1000001021.cmp
Firmware file name example
Product code
2F8: 30/31 ppm printer (EUR/USA model)
2F9: 35/37 ppm printer (EUR/USA model)
2GA: 45/47 ppm printer (EUR/USA model)
Pause (under bar)Pause (period)
Build numberCompression
Software ID
Update history
Classification (Normally: 0)
Firmware category
10: Engine controller
30: Main controller Supplement (Normally: 00)
NOTE:
Main controller firmware 2F9 should 
be used since 35/37 ppm printer and 
45/47 ppm printer are identical.
Downloaded From ManualsPrinter.com Manuals 
						

							2F8/2F9/2GA-1
1-6-2 (1) Downloading the firmware from the parallel interface
To download the system firmware using the parallel interface, use the procedure below.
Note that you can’t download both the system and engine firmware at a time.
1. Turn printer and PC power off.
2. Connect the parallel printer cable between 
the PC and the printer.
Figure 1-6-2
3. Turn printer power on.
4. Confirm that display (1) is displayed.
5. At the DOS prompt, enter command (2).
* Enter UPGR “SYS” in capitals.
6. Confirm that message display (3) is dis-
played.
7. At the DOS prompt, enter command (4) so 
that the system firmware (example: 
S2GA_3000001021.cmp) is copied to the 
printer.
8. Message display (5) is displayed during 
downloading. When message display (6) is 
displayed to indicate downloading is fin-
ished, turn printer power off and then turn 
on.
9. Confirm that message display (7) is dis-
played after warm-up.
10. Print a status page. Check that the status 
page shows the updated firmware version.
Figure 1-6-3
Parallel
interface
connector
Parallel
printer cable
To  P C
(1)
(2)
(3)
(4)
(5)
(6)Message display




 


Supplement (Normally: 00)
Classification (Normally: 0) Product code
2F8: 30/31 ppm printer (EUR/USA model)
2F9: 35/37 ppm printer (EUR/USA model)
2GA: 45/47 ppm printer (EUR/USA model)
Release date: Year/Month/Day  
Checksum Update history
Build number Firmware category
10: Engine controller
30: Main controller c:/>Copy /b S2GA_3000001021.cmp prnc:/echo !R! UPGRSYS;>prn
Supervisor mode
parallel waiting
Downloading
2GA_3000.001.021
05/10/26   [E1F9]

 


(7)Power switch: Off/OnPC DOS display
Ready Ready
NOTE:
Main controller firmware 2F9 should 
be used since 35/37 ppm printer and 
45/47 ppm printer are identical.
Downloaded From ManualsPrinter.com Manuals 
						

							2F8/2F9/2GA-4
1-6-3 (2) Downloading the firmware from the memory card
The procedure below provides how to download firmware from a memory card.
Note that you can download both the system and engine firmware at a time.
1. Turn printer power off.
2. Remove two screws and then remove the 
interface slot cover.
3. Insert the memory card into the printers 
memory card slot.
Figure 1-6-4
4. Turn printer power on.
5. Press Menu key on the printers operation 
panel and carry out the memory card for-
matting procedure (1).
6. When formatting is complete, turn printer 
power off.
Figure 1-6-5
7. Remove the formatted memory card from 
the memory card slot.
8. Insert the memory card to the PCs slot or to 
the adaptor.
9. Copy the firmware file to download to the 
root directory of the memory card.
10. Remove the memory card from the PCs slot 
or the adaptor.
Figure 1-6-6
Memory card slot
Memory card
Interface slot cover
Screw Screw
Message display
(1)Memory Card   >
>Format
>Format ?
ProcessingPress the  key. Press the Menu key.
Press the 
 or  key. Press the 
 or  key.
Press the OK key. Press the OK key. Ready
ReadyOperation panel keys
(Format information is
automatically printed.)
To PC
Memory card
Adaptor
(Memory card read/writer)
Downloaded From ManualsPrinter.com Manuals 
						

							2F8/2F9/2GA-1
1-6-411. Confirm that the printers power switch is set 
to off.
12. Insert the memory card into the printers 
memory card slot.
Figure 1-6-7
13. Turn printer power on.
14. When message display (1) is displayed to 
detect firmware in the memory card.
15. Message display (2) is displayed during 
downloading.
16. When message display (3) is displayed to 
indicate downloading is finished.
17. Turn printer power off.
18. Remove the memory card from memory 
card slot.
19. Turn printer power on.
20. Confirm that message display (4) is dis-
played after warm-up.
21. Print the status page. Print the status page 
to check that the firmware version has been 
updated.
Figure 1-6-8
Memory card slotMemory card
(2)
(1)
(4)
Ready
Supervisor mode
CF-card reading Supervisor mode
(3)2GA_3000.001.021
05/10/26   [E1F9]





Memory
card
slotMemory
card
Message display




 


Supplement (Normally: 00)
Classification (Normally: 0) Product code
2F8: 30/31 ppm printer (EUR/USA model)
2F9: 35/37 ppm printer (EUR/USA model)
2GA: 45/47 ppm printer (EUR/USA model)
Release date: Year/Month/Day
Checksum Update history
Build number Firmware category
10: Engine controller
30: Main controller Power switch: On
Power switch: On Power switch: OffNOTE:
Main controller firmware 2F9 should 
be used since 35/37 ppm printer and 
45/47 ppm printer are identical.
Downloaded From ManualsPrinter.com Manuals 
						

							2F8/2F9/2GA-2
1-6-5 (3) Downloading the firmware from the USB memory
The procedure below provides how to download firmware from a memory card.
Note that you can’t download both the system and engine firmware at a time.
1. Turn printer power off.
2. Connect the USB memory to the PC.
3. Copy the firmware file to the root directory of 
the USB memory.
4. Remove the USB memory from the PC and 
then insert the USB memory into the 
printers USB memory slot.
Figure 1-6-9
5. Turn printer power on.
6. When message display (1) is displayed to 
detect firmware in the USB memory.
7. Message display (2) is displayed during 
downloading.
8. When message display (3) is displayed to 
indicate downloading is finished.
9. Turn printer power off.
10. Remove the USB memory from USB mem-
ory slot.
11. Turn printer power on.
12. Confirm that message display (4) is dis-
played after warm-up.
13. Print the status page. Print the status page 
to check that the firmware version has been 
updated.
Figure 1-6-10
USB memory slot
USB memory
(2)
(1)
(4)
Ready
Supervisor mode
USB data reading Supervisor mode
(3)2GA_3000.001.021
05/10/26   [E1F9]





Message display




 


Supplement (Normally: 00)
Classification (Normally: 0) Product code
2F8: 30/31 ppm printer (EUR/USA model)
2F9: 35/37 ppm printer (EUR/USA model)
2GA: 45/47 ppm printer (EUR/USA model)
Release date: Year/Month/Day
Checksum Update history
Build number Firmware category
10: Engine controller
30: Main controller Power switch: On
Power switch: On Power switch: Off
USB
memory
slot
USB
memory
NOTE:
Main controller firmware 2F9 should 
be used since 35/37 ppm printer and 
45/47 ppm printer are identical.
Downloaded From ManualsPrinter.com Manuals 
						

							2F8/2F9/2GA
1-6-6This page is intentionally left blank.
Downloaded From ManualsPrinter.com Manuals