Kyocera FS 2000D User Manual
Have a look at the manual Kyocera FS 2000D User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 73 Kyocera manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 89
2F8/2F9/2GA-1
1-5-17 (3) Detaching and refitting the heat roller
Procedure
1. Remove the fuser heater lamp (See page
P.1-5-15).
2. Remove the heat roller (assembly) from the
fuser upper frame.
3. Remove the heat gear Z36, heat R bush
and heat L bush from the heat roller. (30/31
ppm printer [EUR/USA model])
Remove the heat gear Z46, two bearings
and two stoppers from the heat roller. (35/37
and 45/47 ppm printer [EUR/USA model])
4. Check or replace the heat roller and refit all
the removed parts....](http://img.usermanuals.tech/thumb/2828/37275/w64_Kyocera_FS-2000D-88.png "Page 89
2F8/2F9/2GA-1
1-5-17 (3) Detaching and refitting the heat roller
Procedure
1. Remove the fuser heater lamp (See page
P.1-5-15).
2. Remove the heat roller (assembly) from the
fuser upper frame.
3. Remove the heat gear Z36, heat R bush
and heat L bush from the heat roller. (30/31
ppm printer [EUR/USA model])
Remove the heat gear Z46, two bearings
and two stoppers from the heat roller. (35/37
and 45/47 ppm printer [EUR/USA model])
4. Check or replace the heat roller and refit all
the removed parts....")
![Page 92
2F8/2F9/2GA-1
1-5-206. Remove the heat roller (See page P.1-5-17).
7. Remove the one screw and then remove the
fuser thermistor M/S.
Figure 1-5-25
8. Remove the one screw (nut) and then
remove the fuser thermistor M (35/37 and
45/47 ppm printer [EUR/USA model] only).
Figure 1-5-26
Fuser thermistor S
Fuser thermistor M
Screw
Screw
30/31 ppm printer
(EUR/USA model)
35/37 and 45/47 ppm printer
(EUR/USA model)
Nut Screw
Fuser
thermistor
M
35/37 and 45/47 ppm printe
r(EUR/USA model)
Downloaded From...](http://img.usermanuals.tech/thumb/2828/37275/w64_Kyocera_FS-2000D-91.png "Page 92
2F8/2F9/2GA-1
1-5-206. Remove the heat roller (See page P.1-5-17).
7. Remove the one screw and then remove the
fuser thermistor M/S.
Figure 1-5-25
8. Remove the one screw (nut) and then
remove the fuser thermistor M (35/37 and
45/47 ppm printer [EUR/USA model] only).
Figure 1-5-26
Fuser thermistor S
Fuser thermistor M
Screw
Screw
30/31 ppm printer
(EUR/USA model)
35/37 and 45/47 ppm printer
(EUR/USA model)
Nut Screw
Fuser
thermistor
M
35/37 and 45/47 ppm printe
r(EUR/USA model)
Downloaded From...")
![Page 95
2F8/2F9/2GA-1
1-5-23 10. Detach the joint.
11. Remove the eight screws and then remove
the DU base.
12. Remove the cord cover (35/37 and 45/47
ppm printer [EUR/USA model] only).
13. Remove the connector (35/37 and 45/47
ppm printer [EUR/USA model] only).
14. Remove the six screws and then remove the
DU base.
Figure 1-5-30
15. Remove the four snaps.
16. Remove the one tab.
17. Remove the one screws and then remove
the grounding terminal.
Figure 1-5-31
DU baseJoint
ConnectorCord cover
Screw
Screw...](http://img.usermanuals.tech/thumb/2828/37275/w64_Kyocera_FS-2000D-94.png "Page 95
2F8/2F9/2GA-1
1-5-23 10. Detach the joint.
11. Remove the eight screws and then remove
the DU base.
12. Remove the cord cover (35/37 and 45/47
ppm printer [EUR/USA model] only).
13. Remove the connector (35/37 and 45/47
ppm printer [EUR/USA model] only).
14. Remove the six screws and then remove the
DU base.
Figure 1-5-30
15. Remove the four snaps.
16. Remove the one tab.
17. Remove the one screws and then remove
the grounding terminal.
Figure 1-5-31
DU baseJoint
ConnectorCord cover
Screw
Screw...")
2F8/2F9/2GA-1 1-5-19 (5) Detaching and refitting the fuser thermistor M, fuser thermistor S, and thermal cutout Procedure 1. Remove the fuser unit (See page P.1-5-14). 2. Turn the fuser unit bottom side up. 3. Unlatch the six latches and then remove the cord cover. 4. Unlatch the four latches and then remove the fuser drawer connector. 5. Remove the one/two connector(s). Figure 1-5-24 backside view Fuser unitLatch Latch Latch Latch Code cover Fuser drawer connector *: 35/37 and 45/47 ppm printer [EUR/USA model] only. Connector Connector* Latch Latch Latch Downloaded From ManualsPrinter.com Manuals
2F8/2F9/2GA-1 1-5-206. Remove the heat roller (See page P.1-5-17). 7. Remove the one screw and then remove the fuser thermistor M/S. Figure 1-5-25 8. Remove the one screw (nut) and then remove the fuser thermistor M (35/37 and 45/47 ppm printer [EUR/USA model] only). Figure 1-5-26 Fuser thermistor S Fuser thermistor M Screw Screw 30/31 ppm printer (EUR/USA model) 35/37 and 45/47 ppm printer (EUR/USA model) Nut Screw Fuser thermistor M 35/37 and 45/47 ppm printe r(EUR/USA model) Downloaded From ManualsPrinter.com Manuals
2F8/2F9/2GA-1 1-5-21 9. Remove the two screws (nuts) and then remove the terminal and cord plate. 10. Remove the thermal cutout 11. Check or replace the fuser thermistor M and S, thermal cutout and refit all the removed parts. Figure 1-5-27 Cord plate Cord plate Terminal Nut Nut 30/31 ppm printer (EUR/USA model) 35/37 and 45/47 ppm printer (EUR/USA model)Nut NutScrew Screw Screw Screw Thermal cutout Terminal Thermal cutout Downloaded From ManualsPrinter.com Manuals
2F8/2F9/2GA 1-5-22 1-5-8 PWBs (1) Detaching and refitting the engine PWB Procedure 1. Remove the fuser unit (See page P.1-5-14). 2. Remove the top cover (See page P.1-5-2). 3. Remove the left cover (See page P.1-5-3). 4. Remove the PSU fan motor (See page P.1- 5-28). 5. Stand the printer front side up. 6. Remove the five screws and then remove the bottom plate1. 7. Remove the four screws and then remove the bottom plate 2. Figure 1-5-28 8. Remove the two wires from the hooks and notches. 9. Open the DU guide (duplex cover). Figure 1-5-29 Screw Bottom plate 1 Bottom plate 2 Screw Screw Screw ScrewScrewScrewScrewScrew Wire Hook NotchDU guide (duplex cover) Downloaded From ManualsPrinter.com Manuals
2F8/2F9/2GA-1 1-5-23 10. Detach the joint. 11. Remove the eight screws and then remove the DU base. 12. Remove the cord cover (35/37 and 45/47 ppm printer [EUR/USA model] only). 13. Remove the connector (35/37 and 45/47 ppm printer [EUR/USA model] only). 14. Remove the six screws and then remove the DU base. Figure 1-5-30 15. Remove the four snaps. 16. Remove the one tab. 17. Remove the one screws and then remove the grounding terminal. Figure 1-5-31 DU baseJoint ConnectorCord cover Screw Screw Screw Screw ScrewScrew Screw Ta b Snap Snap Snap Snap Grounding terminal Downloaded From ManualsPrinter.com Manuals
2F8/2F9/2GA 1-5-2418. Remove the seven connectors (A). 19. Remove the left wire guide. 20. Remove the three screws and then remove the engine PWB assembly. 21. Remove the two connectors (B) from the engine PWB. Figure 1-5-32 Left wire guide Connector (A) Connector (B)Connector (B) Connector (A)Connector (A) Connector (A) Screw Screw Screw Engine PWB assembly Engine PWB assembly Downloaded From ManualsPrinter.com Manuals
2F8/2F9/2GA 1-5-25 22. Remove the one connector. 23. Remove the two screws (A) and then remove the HV plate. 24. Remove the two screws (B) and then remove the engine R ground plate, engine L ground plate and shield plate. 25. Check or replace the engine PWB and refit all the removed parts. To replace the engine PWB, remove the EEPROM from the old engine PWB and mount it to the new engine PWB. Figure 1-5-33 ConnectorEngine PWB Shield plate HV plate Screw (A) Screw (B)Screw (B) Screw (A) EEPROM Engine L grounding plate Engine R grounding plate Downloaded From ManualsPrinter.com Manuals
2F8/2F9/2GA-2 1-5-26 (2) Detaching and refitting the main PWB Procedure 1. Remove the top cover (See page P.1-5-2). 2. Remove the right and left cover (See page P.1-5-3). 3. Remove the six/seven connectors from the main PWB. 4. Remove the two screws and then remove the connect-R PWB. 5. Remove the wires from clamp. Figure 1-5-34 6. Remove the six screws and then remove the controller box (main PWB). Figure 1-5-35 Connectors (Six/Seven) 45/47 ppm printer (EUR/USA model) only Connect-R PWBMain PWB Screw Clamp Screw Screw Screw Screw ScrewScrew Controller box Downloaded From ManualsPrinter.com Manuals
2F8/2F9/2GA-2 1-5-27 7. Remove the screw and then open the inner cover. 8. Remove the connector (35/37 and 45/47 ppm printer [EUR/USA model] only). Figure 1-5-36 9. Remove the five screws and then remove the main PWB from the controller box. 10. Check or replace the main PWB and refit all the removed parts. Figure 1-5-37 Inner cover Screw Connector ScrewScrew ScrewScrewScrew Main PWBController box Downloaded From ManualsPrinter.com Manuals
2F8/2F9/2GA 1-5-28 (3) Detaching and refitting the power source unit Procedure 1. Remove the top cover (See page P.1-5-2). 2. Remove the right and left cover (See page P.1-5-3). 3. Remove the one connector (YC11) form the connect-L PWB. 4. Remove the two hooks and then remove the PSU fan motor. Figure 1-5-38 Connector (YC11) Connect-L PWB PSU fan motor Hook Hook Downloaded From ManualsPrinter.com Manuals