Kyocera FS 1370DN User Manual

							Connecting and Printing3-7
3Press Z. Each time you press U or V, the selection changes. Refer 
to the explanations below when specifying the settings.
If you are using NetWare, AppleTalk, IPP, SSL Server or 
IPSec to connect to a network, you must enter an administrator ID 
and press [OK]. By default, the administrator ID is  3500. 
If you are using NetWare, AppleTalk, IPP, SSL Server or 
IPSec to connect to a network, you must enter an administrator 
password and press [OK]. By default, the administrator password is 
3500.
Set this item to On when you connect to a network using NetWare. 
In submenu, frame mode can be selected from Auto, 802.3, 
Ethernet-II, SNAP and 802.2.
AppleTalk must be activated (On) for networking with Macintosh 
computers except Mac OS X 10.6.
Set this item to On when you connect to a network using IPP.
Set this item to On when you connect to a network using SSL 
Server. Submenu has items including DES, 3DES, AES, IPP over 
SSL and HTTPS.
Set this item to On when you connect to a network using 
IPSec.
Continued on next page.
ID
_
Password
_
>NetWare            >
  On
>AppleTalk
  On
>IPP
  Off
>SSL Server
  Off
>IPSec
  Off
Downloaded From ManualsPrinter.com Manuals 
						

							3-8Connecting and Printing
Set the Security Level to High.
NetWare
This section explains the procedure for enabling NetWare.
1Enter the administrator ID and password. Then, if NetWare is set to 
Off, use U or V to select On and press [OK].
2Press Z.
3Press [OK]. A blinking question mark (?) appears. Each time you 
press U or V, the selection changes.
4Display the item you want to set and press [OK].
5Press [MENU]. The display returns to Ready.
>Security Level
 High
>NetWare            >
  On
>>Frame Type
  Auto
>>Frame Type
? 802.3
>>Frame Type
? Ethernet-II
>>Frame Type
? 802.2
>>Frame Type
? SNAP
>>Frame Type
? Auto
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing3-9
AppleTalk
This section explains the procedure for enabling AppleTalk. 
1Enter the administrator ID and password. Then, if AppleTalk is set 
to Off, use U or V to select On.
2Press [OK]. A blinking question mark (?) appears.
3Press [OK] again.
4Press [MENU]. The display returns to Ready.
IPP
This section explains the procedure for enabling IPP. 
1Enter the administrator ID and password. Then, if IPP is set to Off, 
use U or V to select On.
2Press [OK]. A blinking question mark (?) appears.
3Press [OK] again.
4Press [MENU]. The display returns to Ready.
>AppleTalk
  On
>AppleTalk
? On
>IPP
  On
>IPP
? On
Downloaded From ManualsPrinter.com Manuals 
						

							3-10Connecting and Printing
SSL Server
This section explains the procedure for enabling SSL Server.
1Enter the administrator ID and password. Then, if SSL Server is 
set to Off, use U or V to select On and press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question 
mark (?) appears.
4Select On or Off using U or V.
5Press [OK].
6Press [MENU]. The display returns to Ready.
IPSec
This section explains the procedure for enabling IPSec.
1Enter the administrator ID and password. Then, if IPSec is set to 
Off, use U or V to select On.
2Press [OK]. A blinking question mark (?) appears.
3Press [OK] again.
4Press [MENU]. The display returns to Ready.
>SSL Server         >
  On
>>DES
  Off
>>3DES
  Off
>>AES
  Off
>>IPP over SSL
  Off
>>HTTPS
  Off
>>DES
? Off
>IPSec
  On
>IPSec
? On
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing3-11
Security Level
Security Level is primarily a menu used by service representative 
for maintenance work. There is no need for customers to use this menu.
>Security Level
 High
Downloaded From ManualsPrinter.com Manuals 
						

							3-12Connecting and Printing
Printing a Network Interface Status Page
You can print out a status page for the network interface. The network 
status page shows the network addresses, and other information under 
various network protocols about the network interface.
Adjust/Maintenance
Adjust/Maintenance is used to adjust the print quality and to carry out 
printer maintenance.
The options available in Adjust/Maintenance are as follows:
•Restart Printer
•Service
1Press [MENU].
2Press U or V repeatedly until Adjust/Maintenance > appears.
3Press Z while Adjust/Maintenance > is displayed.
4Press U or V repeatedly until >Service > appears.
5Press Z.
6Press U or V repeatedly until >>Print Network Status Page 
appears.
7Press [OK]. A question mark (?) appears.
8Press [OK]. Processing appears and a status page is printed out.
9When printing ends, the display returns to Ready.
IMPORTANTService is primarily a menu used by service 
representative for maintenance work. There is no need for customers 
to use this menu.
Adjust/Maintenance  >
>>Print
 Network Status Page?
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing3-13
Installing the Printer Driver
Ensure the printer is plugged in and connected to the PC before installing the 
printer driver from the CD-ROM.
Installing the Software in Windows
If you are connecting this printer to a Windows PC, follow the next steps to 
install the printer driver. The example shows you how to connect your printer 
to a Windows Vista PC.
You can use either Express Mode or Custom Mode to install the software. 
Express Mode automatically detects connected printers and installs the 
required software. Use Custom Mode if you want to specify the printer port 
and select the software to be installed.
1Turn on the computer and start up Windows.
If the Welcome to the Found New Hardware Wizard dialog box 
displays, select Cancel.
2Insert the CD-ROM supplied with the printer into the optical drive of 
the PC. In Windows 7, Windows Server 2008 and Windows Vista, 
the user account control window may appear. Click Allow.
The installation program launches.
3Click View License Agreement and read the License Agreement. 
Click Accept.
4Click Install software. 
The software install wizard starts up.
From this point, the procedure differs depending on your version of 
Windows and your connection method. Proceed to the correct 
procedure for your connection type.
•Express Mode
•Custom Mode
NoteIn Windows operating systems, you must be logged in with 
administrator rights to install the printer driver.
NoteIf the software install wizard does not launch 
automatically, open the CD-ROM window in Windows 
Explorer and double-click Setup.exe.
Downloaded From ManualsPrinter.com Manuals 
						

							3-14Connecting and Printing
Express Mode
In Express Mode, the installer automatically detects the printer when 
it is turned on. Use Express Mode for standard connection methods.
1In the installation method selection window, select Express Mode. 
The print system detection window appears and the installer detects 
the connected printers. If the installer does not detect a print system, 
check that the print system is connected via USB or a network and 
that it is turned on. Then click Refresh to search print system again.
2Select the printer you want to be installed, and click Next.
3You can customize the print system name in the installation settings 
window. This will be the name displayed in the Printer window and in 
the printer lists displayed in applications. Specify whether to share 
the print system name or set the print system as an existing printer 
and then click Next.
4A window appears in which you can check the settings. Check the 
settings carefully and then click Install.
5A message appears saying that the printer has been installed 
successfully. Click Finish to exit the printer installation wizard and 
return the CD-ROM main menu.
If the device setup dialog box appears after you click Finish, you 
can specify the settings for items such as optional features installed 
in the print system. You can also specify the device settings after you 
exit the installation. For details, refer to Device Settings in the printer 
driver operation manual on the CD-ROM.
This completes the printer driver installation procedure. Follow the 
on-screen instructions to restart the system, if required.
NoteWhile the information shown in Windows Vista and 
Windows 7/Windows XP installation dialog boxes differs 
slightly, the installation procedure is the same.
NoteIf the Found New Hardware Wizard appears, click 
Cancel. If a hardware installation warning message appear, 
click Continue.
IMPORTANTStep 3 only appears if the print system is 
connected via a network. It does not appear if the print system is 
connected via a USB at the time of the first installation.
NoteIf the Windows security window appears, click Install 
this driver software anyway.
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing3-15
Custom Mode
Use Custom Mode if you want to specify the printer port and select 
the software to be installed.
For example, if you do not want fonts installed on your computer to 
be replaced, select Custom Mode and deselect the Fonts checkbox 
in the utility tab.
1Select Custom Mode.
2Following the instructions in the install wizard window, select the 
software packages to be installed and the specify the port, etc.
For details, refer to Custom Installation in the printer driver operation 
manual on the CD-ROM.
Installation on a Macintosh
This section explains how to install the printer driver in Mac OS X 10.6.
1Turn on the printer and the Macintosh.
2Insert the included CD-ROM (Product Library) into the CD-ROM 
drive.
3Double-click the CD-ROM icon.
4Double-click either OS X 10.2 and 10.3 Only, OS X 10.4 Only or OS 
X 10.5 or higher depending on your Mac OS version.
Downloaded From ManualsPrinter.com Manuals 
						

							3-16Connecting and Printing
5Double-click Kyocera OS X x.x.
6The printer driver installation program starts up.
7Choose Select Destination, Installation Type and then install the 
printer driver as directed by the instructions in the installation 
software.
This completes the printer driver installation. Next, specify the print 
settings.
If an IP or AppleTalk connection is used, the settings below are 
required. If a USB connection is used, the printer is automatically 
recognized and connected.
8Open System Preferences and click Print & Fax.
NoteIn addition to Easy Install, the Installation Type 
options include Custom Install, which allows you to specify 
the components to be installed.
IMPORTANTIn the Authenticate screen, enter the name and 
password used to log in to the operating system.
Downloaded From ManualsPrinter.com Manuals