Kyocera FS 1370DN User Manual

							Loading Paper2-3
3Adjust the paper length guide to the paper size required.
If you are going to use paper that is longer than A4, pull out the 
extension paper cassette by pushing the release lever one by one 
and adjust it to the desired paper size. 
4Load the paper in the cassette. Ensure the side to be printed is 
facing down and the paper is not folded, curled, or damaged. 
NoteDo not load paper above the triangle mark located on 
the width guide.
Downloaded From ManualsPrinter.com Manuals 
						

							2-4Loading Paper
5Insert the paper cassette into the slot in the printer. Push it straight in 
as far as it will go.
There is a paper gauge on the left side of the front of the paper 
cassette to indicate the remaining paper supply. When paper is 
exhausted, the pointer will go down to the level of (empty).
6Specify the paper size and type for the cassette using control panel. 
For more information, refer to Advanced Operation Guide.
Downloaded From ManualsPrinter.com Manuals 
						

							Loading Paper2-5
Loading Paper into MP (Multi-Purpose) Tray
This machine can load up to 50 sheets of 11 × 8 1/2 or A4 paper 
(80 g/m²) into the MP tray.
1Pull the MP tray towards you until it stops.
2Adjust the position of the paper guides on the MP tray. Standard 
paper sizes are marked on the MP tray. For standard paper sizes, 
slide the paper guides to the corresponding mark.
3Pull out the subtray.
4Align the paper with the paper guides and insert as far as it will go.
NoteDo not load more paper than exceeds the tab of the MP 
tray.
Downloaded From ManualsPrinter.com Manuals 
						

							2-6Loading Paper
When loading envelope, place with the envelope flap closed and 
keep the printing side face-up. Insert envelope against the guide 
with the flap on the front or left side until they stop.
5Specify the paper size and type for MP tray using control panel. For 
more information, refer to Advanced Operation Guide.
Paper Stopper
Open the paper stopper shown in the figure.
NoteIf the paper is considerably curled in one direction, for 
example, if the paper is already printed on one side, try to roll 
the paper in the opposite direction to counteract the curl. 
Printed sheets will then come out flat.
Correct
Incorrect
Correct
Correct
Incorrect
12
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing3-1
3Connecting and Printing
This chapter explains how to start up the printer, print from your PC, and 
use the application software included in the CD-ROM.
Connections 3-2
Changing Network Interface Parameters 3-4
Printing a Network Interface Status Page 3-12
Installing the Printer Driver 3-13
Printing 3-19
Status Monitor 3-20
Uninstalling Software (Windows PC) 3-24
Downloaded From ManualsPrinter.com Manuals 
						

							3-2Connecting and Printing
Connections
This section explains how to start up the printer.
Connecting the USB Cable
Follow the steps as below for connecting the USB cable.
1Connect the USB cable to the USB Interface Connector.
2Connect the other end of the USB cable to the computers USB 
interface connector.
Connecting the Network Cable
Follow the steps as below for connecting the network cable.
1Remove the cap attached to the printer.
2Connect the printer to the PC or your network device. 
NoteUse a USB cable with a rectangular Type A plug and a 
square Type B plug. This cable is sold separately.
NoteUse shielded interface cables. These cables are sold 
separately.
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing3-3
Connecting the Power Cord
Install the printer close to an AC wall outlet. If an extension cord is used, 
the total length of the power cord plus extension should be 5 meters (16 
feet) or less.
1Connect the power cord to the Power Cord Connector at the rear of 
the printer.
2Connect the other end of the power cord to a power outlet.
3Press the Power Switch to On ( | ). The printer begins to warm up.
NoteEnsure the printers power switch is off. Only use the power 
cord supplied with the printer. 
IMPORTANTIf you install the starter toner container and switch 
on the power, after a moment the message 
Please 
wait(Adding toner)
 is displayed. When the printer is first 
switched on after toner installation, there will be a delay of 
approximately 15 minutes before the printer gets ready to print. 
Once the [Ready] indicator lights, printer installation is complete.
Downloaded From ManualsPrinter.com Manuals 
						

							3-4Connecting and Printing
Changing Network Interface Parameters
This printer supports TCP/IP, TCP/IP (IPv6), NetWare, AppleTalk, IPP, 
SSL Server, IPSec protocols, and Security Level. For more information, 
refer to the Advanced Operation Guide.
TCP/IP, TCP/IP (IPv6) settings
1
Press [MENU].
2Press U or V repeatedly until Network > appears.
3Press Z. Each time you press U or V, the selection changes. Refer 
to the explanations below when specifying the settings.
Set this item to On when you connect to a network using TCP/IP. 
Submenu has items including DHCP, IP Address, Subnet Mask, 
Gateway and Bonjour.
Set this item to On when you connect to a network using TCP/IP 
(IPv6). Submenu has items including RA(Stateless)and 
DHCPv6.
NoteAfter all network related settings have been done, turn the 
machine OFF and ON again. This is mandatory to make the 
settings effective.
Network             >
>TCP/IP
  Off
>TCP/IP (IPv6)
  Off
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing3-5
TCP/IP
This section describes how to enable the TCP/IP protocol. 
1If TCP/IP is set to Off, use U or V to select On and press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question 
mark (?) appears while you are setting DHCP and Bonjour. A 
blinking cursor (_) appears while you are setting IP Address, 
Subnet Mask and Gateway.
4Press U or V to select On or Off as the setting for DHCP and 
Bonjour.
For the IP Address, Subnet Mask and Gateway settings, press 
U or V to move the blinking cursor to the number you want to 
change (000 to 255). Use Y and Z to move the cursor right and left.
5Press [OK].
6Press [MENU]. The display returns to Ready.
NoteCheck with your network administrator for the network 
address settings. 
>TCP/IP
  On
>>DHCP
  Off
>>IP Address
      000.000.000.000
>>Subnet Mask
      000.000.000.000
>>Gateway
      000.000.000.000
>>Bonjour
  Off
>>Subnet Mask
      000.000.000.000
Downloaded From ManualsPrinter.com Manuals 
						

							3-6Connecting and Printing
TCP/IP (IPv6)
This section describes how to enable the TCP/IP (IPv6) protocol.
1If TCP/IP (IPv6) is set to Off, use U or V to select On and press  
[OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question 
mark (?) appears while you are setting RA(Stateless) and 
DHCPv6.
4Press U or V to select On or Off as the setting for 
RA(Stateless) and DHCPv6.
5Press [OK].
6Press [MENU]. The display returns to Ready.
NetWare, AppleTalk, IPP, SSL Server, IPSec and 
Security Level settings
1
Press [MENU].
2Press U or V repeatedly until Security > appears.
NoteCheck with your network administrator for the network 
address settings. 
>TCP/IP (IPv6)
  On
>>RA(Stateless)
  Off
>>DHCPv6
  Off
>>RA(Stateless)
? Off
>>DHCPv6
? Off
Security            >
Downloaded From ManualsPrinter.com Manuals