Konica Minolta magicolor 2590MF User Manual

Status, Error, and Service Messages 197
SET ORIGINAL TO ADF2in1 or collated 
copying is speci-
fied, but the docu-
ment is not loaded 
into the ADF.Load the document 
into the ADF. 2in1 and 
collated copying can 
only be used with a 
document loaded into 
the ADF.
X TONER 
(Displaying alternately) 
EMPTY
Toner cartridge X 
has become empty.
(This message 
appears if 
8 
TONER EMPTY 
STOP
 on the 
MACHINE SET-
TING
 menu is set 
to 
ON(FAX) or 
OFF.)Replace the specified 
toner cartridge.
X TONER...

Status, Error, and Service Messages 198
X TONER EMPTY 
(Displaying alternately) 
CHANGE X TONER
The X toner car-
tridge is empty.
(This message 
appears if 
8 
TONER EMPTY 
STOP
 on the 
MACHINE SET-
TING
 menu is set 
to 
ON.)Replace the toner car-
tridge.
TONER LIFE END 
(Displaying alternately) 
CHANGE X TONER
The X toner car-
tridge is empty.Replace the toner car-
tridge. This message... means... Do this...
Downloaded From ManualsPrinter.com Manuals 

Status, Error, and Service Messages 199 Service Messages
These messages indicate a more serious fault that can only be corrected by a 
customer service engineer. If one of these messages appears, turn the 
machine off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.
This service message... means... Do this...
*CAUTION!* 
MACHINE TROUBLE
 
(Displaying alternately) 
SERVICE CALL(XX)
An error has been 
detected with the item 
indicated “
XX” in the...

Status, Error, and Service Messages 200
Downloaded From ManualsPrinter.com Manuals 

11
11Installing 
Accessories
Downloaded From ManualsPrinter.com Manuals 

Introduction 202
Introduction
Note
Any damage to the machine caused by the use of accessories not 
manufactured or supported by KONICA MINOLTA will void your 
warranty. 
This chapter provides information about the following accessories.
Note
Installing accessories always requires that the machine and 
accessories are turned off and unplugged during installation.
For details on the available options, refer to 
http://printer. konicaminolta.com. Duplex OptionAuto duplexing
Tr a y  2Lower feeder unit with...

Duplex Option 203
Duplex Option
Duplex (Double-Sided) printing can be performed automatically with the 
duplex option installed.
Installing the Duplex Option
1Turn off the machine, and then 
disconnect the power cord and 
interface cables.
Downloaded From ManualsPrinter.com Manuals 

Duplex Option 204
2Remove the two knockout plates 
and the tape.
Be sure to remove the 
tape.
3Prepare the duplex option.
Before installing the 
duplex option, open the 
duplex cover and check 
that the knob is posi-
tioned vertically. After 
checking the knob, close 
the cover.
Downloaded From ManualsPrinter.com Manuals 

Duplex Option 205
4Install the duplex option.
5Open the cover of the duplex 
option.
Since the duplex option is 
not yet secured to the 
machine, hold the duplex 
option in place when 
opening its cover.
Downloaded From ManualsPrinter.com Manuals 

Duplex Option 206
6While pushing in the knobs, turn 
them clockwise until they are 
horizontal.
The duplex option is secured in 
place.
Make sure that both 
knobs are securely 
locked.
7Close the duplex cover.
Downloaded From ManualsPrinter.com Manuals