Konica Minolta magicolor 1690MF User Manual

							Introduction 10-2
Introduction
Note
Any damage to the machine caused by the use of accessories not 
manufactured or supported by KONICA MINOLTA will void your 
warranty. 
This chapter provides information about the following accessories.
Note
Installing accessories always requires that the machine and 
accessories are turned off and unplugged during installation.
For details on the available options, refer to 
http://printer. konicaminolta.com. Tray 2Lower feeder unit with 500-sheet tray included
Duplex OptionAuto duplexing
In order for the duplex option to be installed, 
Tray 2 must be installed on the machine.
Duplex Option and 
Attachment Auto duplexing
The attachment is an interface unit for installing 
the duplex option on the machine.
During installation, install the attachment before 
installing the duplex option.
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 2 (Lower Feeder Unit)10-3
Tray 2 (Lower Feeder Unit)
You can install up to one optional lower feeder unit (Tray 2). The lower feeder 
unit increases your machine’s media feed capacity by 500 sheets. 
Kit Contents
„Lower feeder unit with a tray (500-sheet capacity)
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 2 (Lower Feeder Unit) 10-4
Installing Tray 2
Note
Since consumables are installed in the machine, be sure to keep the 
machine level when moving it in order to prevent accidental spills.
1Turn off the machine and discon-
nect the power cord and inter-
face cables.
2Remove the dust cover from Tray 1.
Close Tray 1 and the output tray.
3Prepare the lower feeder unit.
Be sure to place the lower feeder unit on a level surface.
4Lift the machine and place it on 
top of the lower feeder unit, mak-
ing sure that the positioning pins 
on the lower feeder unit correctly 
fit into the holes on the bottom of 
the machine.
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 2 (Lower Feeder Unit)10-5
WARNING!
This machine weighs approximately 21 kg (46 lb) when it is fully loaded 
with consumables. 
5Open Tray 1 and reattach the dust cover.
6Load paper into Tray 2.
For details on loading paper, refer to “Tray 2” in “Loading Media” on 
pages.
7Insert Tray 2 into the machine.
Downloaded From ManualsPrinter.com Manuals 
						

							Tray 2 (Lower Feeder Unit) 10-6
8When installing Tray 2 without installing the duplex option, also install the 
locking pins (one in each opening on the left and right sides at the back of 
Tray 2).
While holding the grip of the locking pin vertical, insert the locking pin into 
the opening on either the left or right side of the lower feeder unit and, 
while pushing it in, turn it to either the left or the right. The locking pin is 
installed when its grip is horizontal.
Installing the left and right locking pins secures the lower feeder unit to the 
machine so it cannot be removed.
This step can be skipped if the duplex option is to be installed after 
installing Tray 2.
To uninstall the lower feeder unit from the machine, remove the lock-
ing pins on the left and right side at the back of Tray 2, and then 
remove the lower feeder unit. To remove a locking pin, turn it to either 
the left or the right so that its grip is vertical, and then pull out the lock-
ing pin to remove it.
9Reconnect all interface cables.
10Reconnect the power cord, and 
turn on the machine.
Downloaded From ManualsPrinter.com Manuals 
						

							Duplex Option10-7
Duplex Option
Duplex (Double-Sided) printing can be performed automatically with the 
duplex option installed.
For details, refer to “About Duplex Printing” on page 3-22.
In order for the duplex option to be installed, either of the following must be 
installed on the machine.
zTray 2
zAttachment
Kit Contents
If Tray 2 is installed, it is not necessary to install the attachment. In this 
case, skip “Installing the Attachment”, and continue with “Installing the 
Duplex option” on page 10-9.
Duplex optionAttachment
Downloaded From ManualsPrinter.com Manuals 
						

							Duplex Option 10-8
Installing Attachment
If the attachment is installed, the duplex option can be installed.
(The attachment cannot be used by itself; it must be used together with the 
duplex option.)
Note
Since consumables are installed in the machine, be sure to keep the 
machine level when moving it in order to prevent accidental spills.
1Turn off the machine and discon-
nect the power cord and inter-
face cables.
2Remove the dust cover from Tray 1.
Close Tray 1 and the output tray.
3Prepare the attachment.
Be sure to place the attachment on a level surface.
4Lift the machine and place it on 
top of the attachment, making 
sure that the positioning pins on 
the attachment correctly fit into 
the holes on the bottom of the 
machine.
Downloaded From ManualsPrinter.com Manuals 
						

							Duplex Option10-9
WARNING!
This machine weighs approximately 21 kg (46 lb) when it is fully loaded 
with consumables.
5Open Tray 1 and reattach the dust cover.
Next, install the duplex option.
Installing the Duplex option
The illustrations in the following installation procedure show the 
machine with Tray 2 installed; however, the installation procedure 
would be the same if the attachment was installed.
1Turn off the machine and discon-
nect the power cord and inter-
face cables.
Downloaded From ManualsPrinter.com Manuals 
						

							Duplex Option 10-10
2Remove the tape affixed to the 
rear cover.
3If the locking pins are installed  on the left and right side at the back of 
Tray 2, remove them. 
To remove a locking pin, turn it to either the left or the right so that its grip 
is vertical, and then pull out the locking pin to remove it.
4Prepare the duplex option.
Downloaded From ManualsPrinter.com Manuals 
						

							Duplex Option10-11
5Install the duplex option.
Align the duplex option with its 
installation position, and then 
push down on the bottom of the 
duplex option until it locks into 
place.
Note
When attaching the duplex option, attach the bottom of the option first. 
If the duplex option is attached incorrectly, it may be damaged.
6Open the duplex cover.
While holding the duplex option 
against the machine, tighten the 
screws inside the cover to com-
plete the installation of  the 
duplex option.
7Reconnect all interface cables.
Downloaded From ManualsPrinter.com Manuals