Konica Minolta Di2011 User Manual

77.3 Setting Up the Paper Sources (“PAPER SOURCE SETUP” Menu)
7-18 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
To specify the automatic paper size detection units (“INCH/METRIC” 
function)
1Select the “PAPER SOURCE SETUP” 
menu.
❍Refer to “To select the “PAPER 
SOURCE SETUP” menu” on 
page 7-17.
2Press the [1] key from the 10-Key Pad 
to select “INCH/METRIC”.
3Using the and keys, select a 
paper tray, and then press the [Yes] 
key.
4Using the and keys, select 
either “METRIC” or “INCH”, and...

7.3 Setting Up the Paper Sources (“PAPER SOURCE SETUP” Menu)7
Di1611/Di2011 7-19
Utility Mode – Copy Functions
Chapter 7
To specify the size of paper loaded into the 1st Tray (“TRAY1 PAPER” 
function)
1Select the “PAPER SOURCE SETUP” 
menu.
❍Refer to “To select the “PAPER 
SOURCE SETUP” menu” on 
page 7-17.
2Press the [2] key from the 10-Key Pad 
to select “TRAY1 PAPER”.
3Using the and keys, select 
“PLAIN”, “OHP”, “CARD” or 
“ENVELOPE”, and then press the 
[Yes] key.
4Using the and keys, select 
either...

77.3 Setting Up the Paper Sources (“PAPER SOURCE SETUP” Menu)
7-20 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
✎
Note
The paper length is set between 
421 mm and 432 mm, the 
maximum width that can be set is 
279 mm.
The paper width is set between 
280 mm and 297 mm, the 
maximum length that can be set is 
420 mm.
?Have the necessary precautions been observed when entering the paper 
size?
➜Refer to the diagram at the right 
and be sure to specify the paper 
width and length measurements...

7.3 Setting Up the Paper Sources (“PAPER SOURCE SETUP” Menu)7
Di1611/Di2011 7-21
Utility Mode – Copy Functions
Chapter 7
7Press the [Yes] key.
The “PAPER SOURCE SETUP” menu appears again.
Downloaded From ManualsPrinter.com Manuals 

77.3 Setting Up the Paper Sources (“PAPER SOURCE SETUP” Menu)
7-22 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
To set the “PAPER TYPE” function
1Select the “PAPER SOURCE SETUP” 
menu.
❍Refer to “To select the “PAPER 
SOURCE SETUP” menu” on 
page 7-17.
2Press the [3] key from the 10-Key Pad 
to select “PAPER TYPE”.
3Using the and keys, select a 
paper tray, and then press the [Yes] 
key.
4Using the and keys, select 
either “PLAIN”, “RECYCLE” or 
“SPECIAL”, “1-SIDE” and then press 
the [Yes]...

7.4 Specifying User-Managed Service Tasks (“USER MANAGEMENT” Menu)7
Di1611/Di2011 7-23
Utility Mode – Copy Functions
Chapter 7
7.4 Specifying User-Managed Service Tasks (“USER 
MANAGEMENT” Menu)
From the “USER MANAGEMENT” menu, certain service operations can be 
performed in order to maintain the machine’s efficiency.
“USER MANAGEMENT” menu:
No.USER MANAGEMENTDescription
1 DRUM  DEHUMIDIFY When the room temperature changes drastically (such as when 
a heater is used in the winter) or when the machine is...

77.4 Specifying User-Managed Service Tasks (“USER MANAGEMENT” Menu)
7-24 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
To perform the “DRUM DEHUMIDIFY” function
1Press the [Utility] key.
“MACHINE SETTING?” appears.
2Press the key twice to select 
“USER MANAGEMENT?”, and then 
press the [Yes] key.
3Using the and keys, select 
“DRUM DEHUMIDIFY?”, and then 
press the [Yes] key.
Drum drying begins, and the main 
screen appears.
Downloaded From ManualsPrinter.com Manuals 

7.4 Specifying User-Managed Service Tasks (“USER MANAGEMENT” Menu)7
Di1611/Di2011 7-25
Utility Mode – Copy Functions
Chapter 7
To perform the “TONER REPLENISHER” function
1Press the [Utility] key.
“MACHINE SETTING?” appears.
2Press the key twice to select 
“USER MANAGEMENT?”, and then 
press the [Yes] key.
3Using the and keys, select 
“TONER REPLENISHER?”, and then 
press the [Yes] key.
Toner replenishing begins, and the 
main screen appears.
✎
Note
While the toner is being replenished, do not turn off...

77.5 Specifying Administrative Settings (“ADMIN. MANAGEMENT” Menu)
7-26 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
7.5 Specifying Administrative Settings (“ADMIN. 
MANAGEMENT” Menu)
From the “ADMIN. MANAGEMENT” menu, various functions for controlling the use 
of the machine can be set. In order to set an “ADMIN. MANAGEMENT” function, 
the administrator access number must be entered.
“ADMIN. MANAGEMENT” menu:
✎
Note
The registering and setup of the administrator access number should be...

7.5 Specifying Administrative Settings (“ADMIN. MANAGEMENT” Menu)7
Di1611/Di2011 7-27
Utility Mode – Copy Functions
Chapter 7
To select the “ADMIN. MANAGEMENT” menu
1Press the [Utility] key.
“MACHINE SETTING?” appears.
2Press the key 3 times to select 
“ADMIN. MANAGEMENT?”.
3From the 10-Key Pad, press the key ([1] through [2]) for the “ADMIN. 
MANAGEMENT” function that you wish to set.
❍The “ADMIN. MANAGEMENT” functions are as follows:
1 AUTO SHUT OFF
2 COPY TRACK
4Using the 10-Key Pad, enter the 6-...