Konica Minolta Di2011 User Manual

88.1 When the Message “TONER EMPTY” Appears
8-2 Di1611/Di2011
Error Messages
Chapter 8
8.1 When the Message “TONER EMPTY” Appears
When toner is about to run out, the message shown below appears.
When this message appears, replace the toner bottle with a new one.
✎
Note
Use only toner developed specifically for this machine. Use of any other type of 
toner may cause damage to the machine. For details, contact your service 
representative.
In order to prevent the used toner cartridge from dirtying...

8.1 When the Message “TONER EMPTY” Appears8
Di1611/Di2011 8-3
Error Messages
Chapter 8
2Swing out the Toner Bottle Holder, 
and then remove the toner bottle.
3Holding the sealed end of the new 
toner bottle up, slowly peel off the seal 
toward you.
?Have the necessary precautions 
been observed when peeling off 
the seal?
➜Since some toner may spurt out 
while the seal is being peeled off, 
be sure to peel off the seal slowly.
4With the side of the toner bottle 
marked “UP” facing up, insert the 
toner...

88.1 When the Message “TONER EMPTY” Appears
8-4 Di1611/Di2011
Error Messages
Chapter 8
6Close the Toner Bottle Holder, and 
then close the Front Cover.
❍When the Front Cover is closed, 
the toner automatically begins 
refilling.
?Are copies faint immediately after 
the toner bottle is replaced?
➜Perform the “TONER 
REPLENISHER” function in the 
Utility mode (“To perform the 
“TONER REPLENISHER” 
function” on page 7-25).
Downloaded From ManualsPrinter.com Manuals 

8.2 When the Message “PAPER JAM” Appears8
Di1611/Di2011 8-5
Error Messages
Chapter 8
8.2 When the Message “PAPER JAM” Appears
If a paper misfeed occurs while copying or printing, the message shown below 
appears, and copying or printing stops.
A message indicating the location of the paper misfeed appears in the bottom line 
of the screen.
Follow the appropriate procedure described below to clear the misfed paper.
To clear a paper misfeed in the Duplex Unit
✎
Note
The optional Duplex Unit must be...

88.2 When the Message “PAPER JAM” Appears
8-6 Di1611/Di2011
Error Messages
Chapter 8
To clear a paper misfeed in the main unit or 1st Tray
1Open the Side Cover of the main unit.
CAUTION
The area around the fusing unit is extremely hot.
➜Touching any part other 
than those indicated may 
result in burns. If you get 
burnt, immediately cool the 
skin under cold water, and 
then seek professional 
medical attention.
CAUTION
Decreased copy quality may result if the surface of the PC drum is 
touched.
➜Be...

8.2 When the Message “PAPER JAM” Appears8
Di1611/Di2011 8-7
Error Messages
Chapter 8
2Pull down the Pressure Levers.
?Have the necessary precautions 
been observed when pulling down 
the Pressure Levers?
➜Only hold the green part of the 
Pressure Levers when pulling 
them down.
3Slowly pull out the paper.
4While holding the Guide Plate pressed 
down, slowly pull out the paper.
Pressure Levers
Downloaded From ManualsPrinter.com Manuals 

88.2 When the Message “PAPER JAM” Appears
8-8 Di1611/Di2011
Error Messages
Chapter 8
5While turning the knob on the roller, 
slowly pull out the paper.
?Have the necessary precautions 
been observed when turning the 
roller?
➜Only turn the green knob when 
turning the roller.
➜Be careful not to touch the surface 
of the PC drum.
6Close the Side Cover of the main unit.
7Pull out the 1st Tray.
8Remove all paper from the tray, and 
then place the paper into the tray 
again.
9Slide the paper guides against...

8.2 When the Message “PAPER JAM” Appears8
Di1611/Di2011 8-9
Error Messages
Chapter 8
10Close the 1st Tray.
Downloaded From ManualsPrinter.com Manuals 

88.2 When the Message “PAPER JAM” Appears
8-10 Di1611/Di2011
Error Messages
Chapter 8
To clear a paper misfeed in the Paper Feed Unit
1Open the Side Cover of the Paper 
Feed Unit.
2Slowly pull out the paper.
3Close the Side Cover of the Paper 
Feed Unit.
Downloaded From ManualsPrinter.com Manuals 

8.2 When the Message “PAPER JAM” Appears8
Di1611/Di2011 8-11
Error Messages
Chapter 8
To clear a paper misfeed in the Multiple Bypass
CAUTION
Decreased copy quality may result if the surface of the image transfer roller 
is touched.
➜Be careful not to touch the 
surface of the image transfer 
roller.
1Remove all paper from the Multiple 
Bypass.
2Open the Side Cover of the main unit.
Image transfer roller
Downloaded From ManualsPrinter.com Manuals