HP Z800 Owners Manual

							5.Set the hard drive in the carrier at an angle. Carefully separate the lower hard drive carrier rails
, and then lower the drive between them as shown in the following figure.
Align the carrier pins with the drive mounting holes and release the rails to secure the lower-end
of the drive in place.
Figure 5-43  Installing the drive in the carrier
6.Carefully separate the upper hard drive carrier rails 2, and then rotate the drive upright , as
shown above.
Align the carrier pins with the drive mounting holes and release the rails to secure the upper-end
of drive in place.
ENWW Removing and installing components 109 
						

							7.While keeping the hard drive carrier handle in its fully open position, slide the hard drive into the
bay 
 until it comes to a hard stop. When the drive is installed, rotate the handle up until it snaps
into place, fully securing the drive 
2.
NOTE:The hard drive carrier handle is used as a lever to properly seat the connectors and to
securely retain the hard drive. If the handle is closed prematurely, the proper connection is not
made and the hard drive is not retained properly.
Figure 5-44  Installing the drive in the chassis
NOTE:Ensure that the data cable for the selected bay is connected to the proper data port
connector (see 
Hard disk drive cable configuration on page 107).
8.Reinstall all removed components and reconnect any cables that have been disconnected.
110 Chapter 5   Replacing components ENWW 
						

							Removing a hard disk drive from the slot load optical bay
1.Disconnect power from the workstation (see Predisassembly procedures on page 73).
2.Remove the side access panel (see 
Removing the side access panel on page 75).
3.Remove the airflow guide (see 
Removing the airflow guide on page 76).
4.Remove the expansion card support and any card cables that might interfere with slot load
assembly removal.
5.Disconnect the optical drive power cable from the chassis power cable, and the optical drive data
cable from the system board (see 
Removing the slot load optical disk drive on page 99).
6.Disconnect the slot load drive data cable from the system board connector as shown in the following
figure.
Figure 5-45  Disconnecting the data cable from the system board
7.Disconnect the chassis power cable from the slot load drive power connector as shown in the
following figure.
Figure 5-46  Disconnecting chassis power cable from hard disk drive connector
ENWW Removing and installing components 111 
						

							8.Disconnect the data cable from the hard drive  and from the system board connector 2 as shown
in the following illustration.
Figure 5-47  Disconnecting the data cable from the hard drive
9.Disconnect the chassis power cable from the hard drive power connector as shown in the following
figure.
Figure 5-48  Disconnecting chassis power cable from hard drive connector
112 Chapter 5   Replacing components ENWW 
						

							10.Remove the optical bay slot carrier from the chassis.
Lift and hold the drive release latch at the green touch point 
, and then slide the slot load assembly
out of the chassis 
2 as shown in the following figure.
TIP:Push on the slot load assembly from the inside of the chassis.
Figure 5-49  Removing the slot load assembly
11.Remove the four Torx slotted screws that secure the drive in the slot load bay as shown in the
following figure.
Figure 5-50  Removing the drive screws
ENWW Removing and installing components 113 
						

							12.Remove the hard drive from the slot load optical drive carrier as shown in the following figure.
Figure 5-51  Removing the hard drive from the carrier
114 Chapter 5   Replacing components ENWW 
						

							Installing a hard disk drive in the slot load optical bay
1.With power off and the workstation open, remove the expansion card support and any card cables
that might interfere with slot load assembly installation.
2.Remove the slot load optical bay assembly. (See 
Removing the slot load optical disk drive
on page 99 for details.)
3.Place the hard drive in the slot load carrier at an angle and push it into the carrier as shown in the
following figure.
Figure 5-52  Positioning the drive in the carrier
4.Rotate the hard drive flat, and adjust its position so the drive holes align with the carrier holes.
Fasten the drive in the carrier with the four Torx slotted screws supplied with the disk drive as shown
in the following figure.
Figure 5-53  Fasten the hard drive in the carrier
ENWW Removing and installing components 115 
						

							5.Lift and hold the drive release latch at the green touch point  while sliding the slot load carrier
into the bay. When the front of the carrier is near its final position, release the latch, but continue
to slide the carrier inward until the latch closes and engages the carrier 
2.
NOTE:Install the slot load optical bay with the slot load drive at the top.
Figure 5-54  Installing the slot load assembly in the chassis
6.Connect the chassis power cable to the hard drive power connector as shown in the following
figure.
TIP:Place excess cabling in the slot load bay.
Figure 5-55  Connecting chassis power cable to hard drive connector
116 Chapter 5   Replacing components ENWW 
						

							7.Connect the data cable to the hard drive  and to the system board connector 2 as shown in the
following illustration.
If the hard disk drive is SAS, attach a SATA-SAS adapter to the drive before connecting the data
cable.
TIP:Route the data cable along the system board.
Figure 5-56  Connecting the hard drive data cable to the drive
8.Connect the chassis power cable to the slot load optical drive power cable.
Figure 5-57  Connecting chassis and slot load optical drive power cables
ENWW Removing and installing components 117 
						

							9.Reconnect the optical disk drive data cable to the system board.
NOTE:The optical disk drive power/data cable is still connected to the optical disk drive.
Figure 5-58  Connecting optical disk drive data cable to system board
10.Reinstall all removed components and reconnect any cables that have been disconnected.
118 Chapter 5   Replacing components ENWW