HP Z5200 Owners Manual

Problems with Image Clipping ........................................................................................... 44
Some objects are missing from the printed image ............................................................. 45
A PDF file is clipped or objects are missing ....................................................................... 45
2  System Error Codes Introduction .....................................................................................................................

Scan Axis Calibration ....................................................................................................... 139
Service Station Calibration .............................................................................................. 140
Paper Advance Calibration .............................................................................................. 140
Drop Detector Calibration ................................................................................................ 145...

Cutter Assembly ............................................................................................................................... 199
Right Rear Tray Support ....................................................................................................... ........... 200
Left Rear Tray Support ........................................................................................................ ............. 201
Front Panel...

Starwheel Motor ............................................................................................................................... 325
Full Bleed Foam ............................................................................................................... ................  326
7  Preventive Maintenance Preventive Maintenance ........................................................................................................ ........... 328
Moisture on the Printer...

1 Ink Supplies Troubleshooting & PrintQuality
●Introduction
●
Troubleshooting System Error Codes
●
Performing a Service Test on a failed Assembly
●
Performing the Necessary Service Calibrations
●
Solving Ink Supplies Problems
●
Solving Print Quality Problems
●
Using the Front Panel
●
The Printer does not Power ON
●
The Printer Continuous ly Rejects Printheads
●
What to do if the Front Panel is blank
●
Cover Sensors are not Working
●
The Line Sensor has Problems Detecting Media
●
Problems with Color...

●Reading the Diagnostic Print Results
●
The Advanced Diagnostic Prints
●
Reading the Advanced diagnostic Print Results
●
Troubleshooting Print Quality Problems
Introduction
This chapter will guide you through the relevant  steps to take when troubleshooting the printer.
Troubleshooting System Error Codes
Chapter 2, System Error Codes on page 46 contains a list of system error codes and their respective
descriptions and recommended corrective actions.  Only try one recommended action at a time and
check...

Solving Ink Supplies Problems
For information on solving Ink Supplies problems see Solving Ink Supplies problems on page 9 in
this section.
Solving Print Quality Problems
For information on solving  Print Quality problems see Print Quality on page 23 in this section.
Using the Front Panel
Below is a diagram of the front panel.
Key Function
●Arrow
 Keys
Use the Arrow keys to scroll through a menu  or toggle between YES or NO when prompted.
● Cancel
Use the Cancel key to abort or stop 
a procedure or...

Service Key Combinations
●Diagnostic mode
With the printer OFF, press and hold the 
UP and  OK keys. While holding the  Up and  OK keys down,
press and hold the Power key to turn on the printer. Hold all three keys until the Power key stops
flashing, usually about 5 seconds.
● Service Menu (Service Engineers Only)
From the main menu, press and hold the 
Up and  Cancel  keys.
● Service Menu (For users)
From the main menu, press and hold the 
Down and Cancel  keys.
The Printer does not Power ON
1.Check...

What to do if the Front Panel is blank
The LEDs of the formatter (visible through the cover) and the power supply can help you troubleshoot
a problem when the Front Panel is blank.
1. The following image shows the Power Supply LED, looking through the cover.
2.The following image shows the Formatter  LEDs, which are marked I, II and III.
▲Use the following table to interpret the LEDs and find the source of the problem. Remember that
you should read these LEDs when you push the 
Power button. Some...

8OnOnOnOnFront Panel
(Light on)1.Front Panel Front Panelon page 203
2. Formatter 
Formatter on page 296
3. Main PCA 
Electronics Module (MainPCA and PSU) on page 298
4. Front Panel Cable 
Front Panel
on page 203
9 On OnOn On Off Front Panel Front Panel on page 203
Cover Sensors are not Working
1.Perform the Sensors Test  Refer 5. Sensors on page 101.
2. Check if the cable for the faulty sensor  is not damaged and is connected correctly.
3. Replace the faulty Sensor.
The Line Sensor has Problems Detecting...