HP Pavilion Dv6100 Entertainment Notebook Pc Series Service Guide

							Maintenance and Service Guide E–1
E
Connector Pin Assignments
Ta b l e  D - 1
Universal Serial Bus
Pin Signal Pin Signal
1 +5 VDC 3 Data +
2 Data – 4 Ground 
						

							E–2 Maintenance and Service Guide
Connector Pin Assignments
Ta b l e  D - 2
RJ-45 (Network)
Pin Signal Pin Signal
1 Transmit + 5 Unused
2 Transmit – 6 Receive –
3 Receive + 7 Unused
4 Unused 8 Unused 
						

							Connector Pin Assignments
Maintenance and Service Guide E–3
Ta b l e  D - 3
S-Video-Out
Pin Signal Pin Signal
1 TV-Ground 5 TV-CD
2 TV-CVBS 6 TV-Ground
3 TV-Ground 7 TV-YD
4 TV-Ground 
						

							E–4 Maintenance and Service Guide
Connector Pin Assignments
Ta b l e  D - 4
External Monitor
Pin Signal Pin Signal
1 Red analog 9 +5 VDC
2 Green analog 10 Ground
3 Blue analog 11 Monitor detect
4 Not connected 12 DDC 2B data
5 Ground 13 Horizontal sync
6 Ground analog 14 Vertical sync
7 Ground analog 15 DDC 2B clock
8 Ground analog 
						

							Connector Pin Assignments
Maintenance and Service Guide E–5
Ta b l e  D - 5
RJ-11 (Modem)
Pin Signal Pin Signal
1 Unused 4 Unused
2Tip 5Unused
3 Ring 6 Unused 
						

							E–6 Maintenance and Service Guide
Connector Pin Assignments
Ta b l e  D - 6
Audio-In (Microphone)
Pin Signal Pin Signal
1 Audio signal in 3 Ground
2 Audio signal in
Ta b l e  D - 7
Audio-Out (Headphone)
Pin Signal Pin Signal
1 Audio out, left channel 3 Ground
2 Audio out, right channel 
						

							Maintenance and Service Guide F–1
F
Power Cord Set Requirements
3-Conductor Power Cord Set
The wide range input feature of the computer permits it to operate 
from any line voltage from 100 to 120 or 220 to 240 volts AC.
The power cord set included with the computer meets the 
requirements for use in the country or region where the 
equipment is purchased.
Power cord sets for use in other countries and regions must meet 
the requirements of the country or region where the computer is 
used. 
						

							F–2 Maintenance and Service Guide
Power Cord Set Requirements
General Requirements
The requirements listed below are applicable to all countries and 
regions.
■The length of the power cord set must be at least 1.5 m 
(5.0 ft) and a maximum of 2.0 m (6.5 ft).
■All power cord sets must be approved by an acceptable 
accredited agency responsible for evaluation in the country or 
region where the power cord set will be used.
■The power cord sets must have a minimum current capacity 
of 10 amps and a nominal voltage rating of 125 or 250 V AC, 
as required by each country or region’s power system.
■The appliance coupler must meet the mechanical 
configuration of an EN 60 320/IEC 320 Standard Sheet C13 
connector for mating with the appliance inlet on the back of 
the computer. 
						

							Power Cord Set Requirements
Maintenance and Service Guide F–3
Country/Region-Specific Requirements
3-Conductor Power Cord Set Requirements
Country/Region Accredited Agency Applicable Note Number
Australia EANSW 1
Austria OVE 1
Belgium CEBC 1
Canada CSA 2
Denmark DEMKO 1
Finland FIMKO 1
France UTE 1
Germany VDE 1
Italy IMQ 1
Japan METI 3
✎NOTES:
1. The flexible cord must be  Type HO5VV-F, 3-conductor, 1.0 mm²
 
conductor size. Power cord set fittings (appliance coupler and wall plug) 
must bear the certification mark of the agency responsible for evaluation 
in the country or region where it will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 
3-conductor. The wall plug must be a two-pole grounding type with a 
NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark 
and registration number in accordance with the Japanese Dentori Law. The 
flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm² conductor 
size. The wall plug must be a two-pole grounding type with a Japanese 
Industrial Standard C8303 (7 A, 125 V) configuration. 
						

							F–4 Maintenance and Service Guide
Power Cord Set Requirements
Korea EK 4
The Netherlands KEMA 1
Norway NEMKO 1
People’s Republic 
of ChinaCCC 5
Sweden SEMKO 1
Switzerland SEV 1
Taiwan BSMI 4
United Kingdom BSI 1
United States UL 2
✎NOTES:
1. The flexible cord must be  Type HO5VV-F, 3-conductor, 1.0 mm²
 
conductor size. Power cord set fittings (appliance coupler and wall plug) 
must bear the certification mark of the agency responsible for evaluation 
in the country or region where it will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 
3-conductor. The wall plug must be a two-pole grounding type with a 
NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark 
and registration number in accordance with the Japanese Dentori Law. The 
flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm² conductor 
size. The wall plug must be a two-pole grounding type with a Japanese 
Industrial Standard C8303 (7 A, 125 V) configuration.
4. The flexible cord must be Type RVV, 3-conductor, 0.75 mm² conductor size. 
Power cord set fittings (appliance coupler and wall plug) must bear 
the certification mark of the agency responsible for evaluation in the country 
or region where it will be used.
5. The flexible cord must be Type VCTF, 3-conductor, 0.75 mm² conductor 
size. Power cord set fittings (appliance coupler and wall plug) must bear the 
certification mark of the agency responsible for evaluation in the country or 
region where it will be used.
3-Conductor Power Cord Set Requirements (Continued)
Country/Region Accredited Agency Applicable Note Number