HP Pavilion Dv6100 Entertainment Notebook Pc Series Service Guide

							Removal and Replacement Procedures
Maintenance and Service Guide 5–5
5.3 Preparing the Computer For 
Disassembly
Before you begin any removal or installation procedures: 
1. Shut down the computer. If you are unsure whether the 
computer is off or in hibernation, turn the computer on, 
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power cord.
4. Remove the battery by following these steps:
a. Turn the computer upside down with the front panel 
toward you.
Battery Spare Part Number Information
12-cell, 8.8-AHr
6-cell, 4.0-AHr432307-001
432306-001 
						

							5–6 Maintenance and Service Guide
Removal and Replacement Procedures
b. Slide and hold the battery release latch 1 to the left. 
(The front edge of the battery disengages from 
the computer.)
c. Lift the front edge of the battery 2 and swing it back.
d. Remove the battery.
Removing the Battery
Reverse the above procedure to install the battery. 
						

							Removal and Replacement Procedures
Maintenance and Service Guide 5–7
5.4 Hard Drive
1. Prepare the computer for disassembly (refer to Section 5.3).
Hard Drive Spare Part Number Information
For use with all computer models:
200-GB
160-GB
120-GB
100-GB
80-GB
60-GB441424-001
438485-001
431407-001
431406-001
431405-001
431404-001
40-GB hard drive for use only with computer models 
using Intel processors434743-001
40-GB hard drive for use only with computer models 
using AMD processors434415-001
Hard Drive Bracket Kit (includes hard drive bracket 
and 4 screws used to secure the bracket to the 
hard drive)436156-001 
						

							5–8 Maintenance and Service Guide
Removal and Replacement Procedures
2. Loosen the two Phillips PM2.0×5.0 screws 1 that secure 
the hard drive cover to the computer.
3. Lift the right side of the cover 2 and swing it to the left.
4. Remove the hard drive cover.
✎The hard drive cover is included in the Plastics Kit, spare part 
number 438368-001.
Removing the Hard Drive Cover 
						

							Removal and Replacement Procedures
Maintenance and Service Guide 5–9
5. Use the mylar tab 1 to lift the hard drive 2 until it 
disconnects from the computer.
6. Remove the hard drive from the hard drive bay.
Removing the Hard Drive 
						

							5–10 Maintenance and Service Guide
Removal and Replacement Procedures
7. Remove the six Phillips PM3.0×3.0 screws 1 that secure 
the hard drive bracket to the hard drive.
8. Lift the bracket 2 straight up to remove if from the 
hard drive.
Removing the Hard Drive Bracket
Reverse the above procedure to install and reassemble the 
hard drive. 
						

							Removal and Replacement Procedures
Maintenance and Service Guide 5–11
5.5 Computer Feet
The computer feet are adhesive-backed rubber pads. The feet are 
included in the Rubber Feet Kit, spare part number 431430-001. 
The feet attach to the base enclosure in the locations illustrated 
below.
Computer Feet Locations 
						

							5–12 Maintenance and Service Guide
Removal and Replacement Procedures
5.6 Memory Module
1. Prepare the computer for disassembly (refer to Section 5.3).
Memory Module Spare Part Number Information
For use only with computer models using Intel processors:
1024-MB
512-MB
256-MB434742-001
434741-001
434740-001
For use only with computer models using AMD processors:
1024-MB
512-MB
256-MB431403-001
431402-001
431401-001 
						

							Removal and Replacement Procedures
Maintenance and Service Guide 5–13
2. Loosen the two Phillips PM2.0×5.0 screws 1 that secure 
the memory module compartment cover to the computer.
3. Lift the left side of the memory module compartment 
cover2, and then swing it to the right.
4. Remove the memory module compartment cover.
✎The memory module compartment cover is included in the 
Plastics Kit, spare part number 431428-001.
Removing the Memory Module Compartment Cover 
						

							5–14 Maintenance and Service Guide
Removal and Replacement Procedures
5. Spread the retaining tabs 1 on each side of the memory 
module socket to release the memory module. (The edge 
of the module opposite the socket rises away from the 
computer.)
6. Slide the module 2 away from the socket at an angle.
✎Memory modules are designed with a notch 3 to prevent 
incorrect installation into the memory module socket.
Removing a Memory Module
Reverse the above procedure to install a memory module.