HP OfficeJet J4660 User Manual

NOTE:If you encounter problems, see Solve wireless problems (HP Officejet
J4680 only).
To use the device with any wireless  connection, you must run the installation
program at least once from the Starter CD and create a wireless connection.
Make sure the device is not connected to the network using a network cable.
The sending device must have built-in 802.11 capabilities or an 802.11 wireless
card installed.
The device and the computers that use it must be on the same subnet.
Before installing the...

◦Be on the same subnet and same channel
◦ Have the same 802.11 security settings
• Infrastructure (recommended):  On an infrastructure network, the device is set to
infrastructure communication mode and communicates with other devices on the
network, whether the devices are wired or wireless, through a WAP. WAPs
commonly act as routers or gateways on small networks.
Security settings
NOTE: For more information on wireless security, visit www.weca.net/
opensection/pdf/whitepaper_wi-fi_security4-29-03.pdf...

To set up wireless communication using the installer (Windows)
For this method, you will need to have a network set up and running.
1.Set up the device hardware (see the Wireless getting started guide).
2. Remove the protective cover from the devices network port.
3. Close any applications that are  running on your computer system.
4. Insert the Starter CD into the CD drive.  The CD menu runs automatically. If the CD
menu does not start automatically, double-click the  setup icon on the Starter CD.
5....

8.On the  Connection Type  screen, select the wireless network option, and then
click  Done .
9. Follow the onscreen instructions to install the printer driver.
To turn off wireless communication
•Device control panel:  Press Setup, then select  Wireless, then select  Wireless
ON/OFF , and then select either  On or  Off .
• Press the wireless button on the front of the device.
To print a wireless test page
Print the wireless test page for information about the devices wireless connection. The
wireless...

To add hardware addresses to a WAP
MAC filtering is a security feature in which a WAP is configured with a list of MAC
addresses (also called hardware addresses) of devices that are allowed to gain
access to the network through the WAP.
If the WAP does not have the hardware address of a device attempting to access the
network, the WAP denies the device access to the network.
If the WAP filters MAC addresses, then the devices MAC address must be added to
the WAPs list of accepted MAC addresses.
▲Open the...

There are three methods to uninstall the software on a Windows computer, and one
method to uninstall on a Macintosh computer.
To uninstall from a Windows computer, method 1
1.Disconnect the device from your computer. Do  not connect it to your computer until
after you have reinstalled the software.
2. Press the  Power button to turn off the device.
3. On the Windows taskbar, click  Start, select  Programs  or All Programs , select
HP , select  Officejet J4500 Series , and then click Uninstall.
4. Follow...

To uninstall from a Windows computer, method 3
NOTE:Use this method if  Uninstall is not available in the Windows Start menu.
1.Insert the device Starter CD into your  computers CD-ROM drive, and then start
the Setup program.
2. Disconnect the device from your computer.
3. Select  Uninstall  and follow the onscreen directions.
4. Restart your computer.
NOTE: It is important that you disconnect the device before restarting your
computer. Do not connect the device to your computer until after you have...

8 Maintain and troubleshoot
This section contains the following topics:
•
Work with ink cartridges
•
Clean the device
•
General troubleshooting tips and resources
•
Solve printing problems
•
Poor print quality and unexpected printouts
•
Solve paper-feed problems
•
Solve scan problems
•
Solve copy problems
•
Solve fax problems
•
Solve wireless problems (HP Officejet J4680 only)
•
Troubleshoot installation issues
•
Clear jams
Work with ink cartridges
This section contains the following topics:
•
Supported...

Handle the ink cartridges
Before you replace or clean a ink cartridge, you should know the part names and how
to handle the ink cartridges.
1Copper-colored contacts
2Plastic tape with pink pull tab (must be removed before installing)
3Ink nozzles under tape
Hold the ink cartridges by their black plastic sides,  with the label on top. Do not touch
the copper-colored contacts or the ink nozzles.
NOTE: Handle the ink cartridges carefully. Dropping or jarring cartridges can
cause temporary printing...

available to avoid possible printing delays. You do not need to replace the ink
cartridges until print quality becomes unacceptable.
To order ink cartridges for the device, go to 
www.hpshopping.com. If prompted,
choose your country/region, follow the prompts to select your product, and then click
one of the shopping links on the page.
To replace the ink cartridges
1. Make sure the device is on.
CAUTION: If the HP All-in-One is off when you open the front access door to
access the ink cartridges, the...