HP LaserJet 4345mfp User Manual

ItemValuesExplanation
FORM LENGTH5 to  128Sets vertical spacing from 5 to
128 lines for default paper size.
Enter the value by using the
numeric keypad.
ORIENTATIONPORTRAIT *
LANDSCAPESelect the default page
orientation.
Note
It is recommended that you set
the page orientation in the
printer driver or in the software
program. (Printer-driver
settings and software-program
settings override control-panel
settings.)
FONT SOURCEINTERNAL *
CARD SLOT XINTERNAL : Internal fonts.
CARD SLOT 1 , CARD SLOT
2 , or...

Print quality submenu
You can gain access to some of the items in this menu in either a software program, or in
the printer driver (if the correct printer driver is installed). Printer driver settings and software
program settings override control-panel settings. For more information, see 
Using features in
the printer driver .
To gain access to this menu, touch  CONFIGURE DEVICE, and then touch PRINT QUALITY .
ItemValuesExplanation
SET REGISTRATIONPRINT TEST PAGE
SOURCE
ADJUST TRAY Shift the margin...

ItemValuesExplanation
OPTIMIZEHIGH TRANSFER
LINE DETAIL
RESTORE OPTIMIZEThis item optimizes a number
of MFP parameters for all jobs
rather than by media type. The
default setting for each value is
OFF.
Turn  HIGH TRANSFER  on if
parts of the printed image
appear to have extra toner.
Turn  LINE DETAIL  on if lines
and text are blurred.
RESTORE OPTIMIZE  resets
all of the optimize parameters
to the default settings.
RESOLUTION300
600
FASTRES 1200 *
PRORES 1200Select the resolution from the
following...

ItemValuesExplanation
RETOFF
LIGHT
MEDIUM*
DARKUse the Resolution
Enhancement technology (REt)
setting to produce print output
with smooth angles, curves,
and edges.
All print resolutions, including
FastRes 1200, benefit from REt.
Note
It is recommended that you
change the REt setting in the
printer driver or in the software
program. (Printer driver
settings and software program
settings override control-panel
settings.)
ECONOMODEON
OFF *When EconoMode is set to  ON,
the MFP prints with a reduced
amount...

ItemValuesExplanation
AUTO CLEANINGON*
OFFWhen auto-cleaning is on, the
MFP prints a cleaning page
when the page count reaches
the value set in  CLEANING
INTERVAL .
CLEANING INTERVAL1000
2000
5000
10000
20000Select the frequency that you
want the MFP to automatically
print a cleaning page.
AUTO CLEANING SIZELETTER
A4Use this item to specify the
paper size that the MFP uses
to print the cleaning page.
PROCESS CLEANING PAGENo value to selectUse this item to clean the fuser.
The cleaning process might
take...

ItemValuesExplanation
SHOW ADDRESSAUTO
OFF*This item defines whether the
IP address is shown on the
control-panel display next to
the Ready  message.
The default setting is  OFF.
TRAY BEHAVIORUSE REQUESTED TRAY
MANUAL FEED PROMPT
PS DEFER MEDIA
SIZE/TYPE PROMPTSpecifies the behavior of the
tray by indicating which tray the
MFP should print from.
USE REQUESTED TRAY  sets
the tray that the MFP should
print from for specified jobs.
The values for this menu item
are  EXCLUSIVELY  (default) or
FIRST .
MANUAL...

ItemValuesExplanation
SLEEP DELAY1 MINUTE
15 MINUTES
30 MINUTES
60 MINUTES*
90 MINUTES
2 HOURS
4 HOURSSets how long the MFP
remains idle before it enters
sleep mode.Using sleep mode
offers the following advantages::
● Minimizes the amount of
power that the MFP
consumes when it is idle
● Reduces wear on
electronic components in
the MFP
Note
Sleep mode turns off the
backlight on the display, but the
display is still readable.
The MFP automatically exits
sleep mode when you send a
print job, receive a fax,...

ItemValuesExplanation
CLEARABLE WARNINGSON
JOB*Set the amount of time that a
clearable warning appears on
the MFP control panel.
ON: Warning messages appear
on the control panel until they
are cleared.
JOB : Warning messages
appear on the control panel
until the end of the job from
which they were generated.
AUTO CONTINUEON *
OFFThis item determines how the
MFP reacts to errors.
ON : If an error prevents
printing, the message is
displayed, and the MFP goes
offline for 10 seconds before
returning online....

ItemValuesExplanation
JAM RECOVERYAUTO*
ON
OFFDetermine how the MFP
functions when a jam occurs.
AUTO : The MFP automatically
selects the best mode for jam
recovery (usually  ON). This is
the default setting.
ON : The MFP automatically
reprints pages after a jam is
cleared.
OFF : The MFP does not reprint
pages following a jam. Printing
performance might be
increased with this setting.
LANGUAGEList of available languagesSets the language of the
control panel.
Copy/send settings
This table lists the...

ValuesExplanation
EDGE-TO-EDGE COPIESIndicates whether copies are printed edge-to-edge (within 2 mm,
or 0.08 inch, of the edge of the paper) or whether they have the
normal, unprintable border (6.35 mm, or 0.25 inch).
AUDIBLE FEEDBACKGives an audible indication when you press a button or when you
touch an interactive area of the touchscreen.
MBM-3 Configuration submenu
Use the items in this menu to set up the output bins on the 3-bin mailbox.
To gain access to this menu, touch  CONFIGURE DEVICE, and then...