HP Color LaserJet CP2025dn User Manual

Print when cartridge has reached estimated end of life
An Order Supplies  message appears when a print cartridge is nearing the end of its life. A  Replace
supplies  message appears when the print cartridge has  reached its estimated end of life. To ensure
optimal print quality, HP recommends replacing a print cartridge when the  Replace supplies message
appears. Print-quality problems can occur when usin g a cartridge that has reached its estimated end of
life, resulting in waste of print media and...

Replace print cartridges
1.Open the front door.
2.Pull out the print-cartridge drawer.
3.Grasp the handle on the old print cartridge and then pull the cartridge straight up to remove it.
4.Remove the new print cartridge from the packaging.
82 Chapter 9   Manage and maintain ENWW
 

5.Remove the orange, plastic shield from the bottom of the new print cartridge.
CAUTION: Do not touch the imaging drum on the botto m of the print cartridge. Fingerprints on
the imaging drum can cause print-quality problems.
6. Insert the new print cartridge into the product.
ENWW Replace print cartridges 83
 

7.Pull the tab on the left side of the print cartridge straight up to completely remove the sealing tape.
Discard the sealing tape.
8.Close the print-cartridge drawer.
84 Chapter 9   Manage and maintain ENWW
 

9.Close the front door.
10.Place the old print cartridge in the box for the new print cartridge. Follow the recycling instructions
that are included in the box.
ENWWReplace print cartridges 85
 

Memory and font DIMMs
Product memory
The product has one dual inline memory module (DIMM) slot. Use the DIMM slot to upgrade the product
with the following items:
● More product memory (DIMMs are 
available in 64, 128, and 256 MB)
● Other DIMM-based printer languages and product options
● Support-language character sets (for example, Chi
nese characters or Cyrillic alphabet characters).
NOTE:To order DIMMs, see Supplies and accessories on page 125.
You might want to increase product memory if you  often...

3.Remove the DIMM access door.
4.To replace a DIMM that is currently installed, spread the latches apart on each side of the DIMM
slot, lift the DIMM up at an angle, and pull it out.
5.Remove the new DIMM from the antistatic package, and then locate the alignment notch on the
bottom edge of the DIMM.
ENWWMemory and font DIMMs 87
 

6.Holding the DIMM by the edges, align the notch on the DIMM with the bar in the DIMM slot at an
angle.
7.Push down on the DIMM until both latches engage the DIMM. When the installation is correct, the
metal contacts are not visible.
NOTE:If you have difficulty inserting the DIMM, make sure that the notch on the bottom of the
DIMM is aligned with the bar in the slot. If the DIMM still does not go in, make sure that you are
using the correct DIMM type.
8.Reinsert the DIMM access door.
88 Chapter 9...

9.Close the DIMM access door.
10.Reconnect the power cable and USB or network cable, and then turn on the product.
11.After installing a memory DIMM, see 
Enable memory on page 90.
ENWWMemory and font DIMMs 89
 

Enable memory
If you installed a memory DIMM, set the printer driver to recognize the newly added memory.
Enable memory for Windows
1.On the Start menu, point to Settings, and click Printers or Printers and Faxes.
2.Select this product and select Properties.
3.On the Configure tab, click More.
4.In the Total Memory field, type or select the total amount of memory that is now installed.
5.Click OK.
Check DIMM installation
Turn the product on. Check that the product is in the Ready state after it has gone...