HP Color LaserJet CM3530fs MFP User Manual

Menu itemSub-menu itemSub-menu itemValuesDescription
 PCL Form LengthType a value
between 5 and 128
lines. The factory
default is 60 lines.PCL is a set of printer commands that
Hewlett-Packard developed to provide
access to printer features.
OrientationPortrait (default)
LandscapeSelect the orientation that is most often used
for print jobs. Select  Portrait if the short edge
is at the top or Landscape  if the long edge is
at the top.
Font SourceSelect the source
from the list.Select the font source for...

Print Quality menu
Administration > Print Quality
Table 2-16  Print Quality  menu
Menu itemSub-menu itemValuesDescription
Adjust ColorHighlightsCyan Density. Magenta
Density . Yellow Density .
Black Density
+5  to –5. Default is  0.Adjust the darkness or lightness of highlights on a
printed page. Lower values represent lighter highlights
on a printed page, and higher values represent darker
highlights on a printed page.
MidtonesCyan Density . Magenta
Density . Yellow Density .
Black Density
+5  to –5....

Menu itemSub-menu itemValuesDescription
When Transparency Only  is selected, the product
senses only the first page and recognizes only
overhead transparency types.
OptimizeBackgroundNormal  (default)
Alternate 1
Alternate 2
Alternate 3Adjust this setting if you are having problems with an
overall gray background on pages.
 RegistrationNormal  (default)
AlternateAdjust this setting if you are having problems with color
misregistration.
 Transfer ControlNormal  (default)
Alternate 1
Alternate 2
Alternate...

Menu itemSub-menu itemValuesDescription
 Humidity ModeNormal (default)
HighAdjust this setting if you are in a high-humidity
environment and you are having problems with light
density in the printed image.
 Pre-rotationOff  (default)
OnAdjust this setting if you are having problems with
horizontal streaks on printed pages. Using this feature
increases the warm-up time for the product.
 Fuser TempNormal  (default)
Up
DownAdjust this setting upward if toner is not fusing well.
Adjust it downward if you are...

Menu itemSub-menu itemValuesDescription
 Full CalibrationCalibratePerforms all product calibrations.
 Delay Calibration at
Wake/Power OnNo
Yes
 (default) This menu controls the timing of the calibration when
the printer wakes up or is turned on.
●
Select 
No to have the printer calibrate immediately
when it wakes up or is turned on. The product will
not print any jobs until it finishes calibrating.
● Select 
Yes to enable a product that is asleep to
accept print jobs before it calibrates. The product...

Troubleshooting menu
Administration > Troubleshooting
NOTE:Many of the menu items under the  Troubleshooting menu are for advanced troubleshooting
purposes.
Table 2-17   Troubleshooting  menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Event Log  PrintThis shows the event codes and their
corresponding engine cycles on the control-
panel display.
Calibrate Scanner  CalibrateUse this feature to compensate for offsets in
the scanner imaging system (carriage head)
for ADF and flatbed scans.
You...

Menu itemSub-menu itemSub-menu itemValuesDescription
color is the source of a problem. In this mode,
all consumable-related errors are ignored.
Paper Path Sensors   Initiate a test of the paper-path sensors.
Paper Path TestTest Page PrintGenerate a test page for testing the paper-
handling features. Define the path for the test
in order to test specific paper paths.
Source All trays
Tray 1
Tray 2
(Additional trays are
shown, if applicable.)Specify whether the test page is printed from
all trays or from a...

Menu itemSub-menu itemSub-menu itemValuesDescription
Control Panel LEDs  Verify that the components of the control
panel are functioning correctly.
Display
  
Buttons  
Touchscreen   
Table 2-17  Troubleshooting menu (continued)
54 Chapter 2   Control panel ENWW
 

Resets menu
Administration > Resets
Table 2-18   Resets  menu
Menu itemValuesDescription
Clear Local Address BookClearUse this feature to clear all addresses from the address books that
are stored on the product.
Clear Fax Activity LogYes
No (default)Use this feature to clear all events from the Fax Activity Log.
Restore Factory Telecom SettingRestoreUse this option to restore the following settings to their factory default
settings: Transmit Signal Loss, V34, Maximum Baud Rate, Speaker
Mode.
Restore...

Service menu
Administration > Service
The  Service  menu is locked and requires a PIN for access. This menu is intended for use by authorized
service personnel.
56 Chapter 2   Control panel ENWW