HP Color LaserJet CM3530fs MFP User Manual

Paper typeImage orientationDuplex modeHow to load paper
Alternative Letterhead Mode =
OffHow to load paper
Alternative Letterhead Mode =
On
Load Tray 1
TIP:To see an animation of this procedure go to this Web site: www.hp.com/go/cljcm3530mfp-load-
tray1.
CAUTION: To avoid jams, never add or remove paper from Tray 1 during printing.
1.Open Tray 1.
2.Fold out the tray extension to support the paper and set the side guides to the correct width.
ENWW Load paper and print media 97
 

3.Load paper in the tray face down and the short, top edge going into the product first.
4.Make sure the stack fits under the tabs on the guides and does not exceed the load-level indicators.
5.Adjust the side guides so that they lightly touch the paper stack but do not bend it.
98 Chapter 6   Paper and print media ENWW
 

Print envelopes
If your software does not automatically format an envelope, specify Landscape for page orientation in
your software program or printer driver. Use the following guidelines to set margins for return and
destination addresses on Commercial #10 or DL envelopes:
Address typeLeft marginTop margin
Return15 mm (0.6 in)15 mm (0.6 in)
Destination 102 mm (4 in) 51 mm (2 in)
For envelopes of other sizes, adjust the margin settings accordingly.
Load Tray 2
This tray holds up to 250 sheets of 75 g/m2...

2.Adjust the paper-length and paper-width guides by squeezing the adjustment latch and sliding the
guides to the size of the paper being used.
3.Load paper into the tray face up. Check the paper to verify the guides lightly touch the stack, but
do not bend it.
NOTE: To prevent jams, do not overfill the tray. Be sure the top of the stack is below the tray full
indicator.
NOTE: If the tray is not adjusted correctly, an error message might appear during printing or the
paper might jam.
4. Slide the tray...

5.The control panel shows the tray’s paper type and size. If the configuration is not correct, follow
the instructions on the control panel to change the size or type.
HP LaserJet  
DDMMYYYY 00.00 AM
Load the optional 500-sheet pape r and heavy media tray (Tray 3)
Tray 3 holds up to 500 sheets of standard paper.
The product automatically detects the following standard sizes of paper in Tray 3: Letter, Legal,
Executive, A4, A5, and B5 (JIS).
CAUTION:Do not print envelopes or unsupported sizes of paper...

2.Adjust the paper-length and paper-width guides by squeezing the adjustment latches and sliding
the guides to the size of the paper being used.
3.Load paper into the tray face up. Check the paper to verify the guides lightly touch the stack, but
do not bend it.
NOTE: To prevent jams, do not overfill the tray. Be sure the top of the stack is below the tray full
indicator.
NOTE: If the tray is not adjusted correctly, an error message might appear during printing or the
paper might jam.
4. Slide the tray...

5.The control panel shows the tray’s paper type and size. If the configuration is not correct, follow
the instructions on the control panel to change the size or type.
HP LaserJet  
DDMMYYYY 00.00 AM
Load custom-size paper into Tray 3
To use custom media, change the size setting on the control panel to  Custom and set the unit of
measure,  X Dimension  and Y Dimension .
1. Slide open the tray.
2.Adjust the paper-length and paper-width guides by squeezing the adjustment latches and sliding
the guides to...

3.Load paper into the tray face up. Check the paper to verify the guides lightly touch the stack, but
do not bend it.
4.Slide the tray into the product. The control panel shows the paper type and size.
104 Chapter 6   Paper and print media ENWW
 

5.The control panel prompts you to set the paper size and type. Select the  Custom setting, and then
configure the X and Y dimensions of the custom paper size.
HP LaserJet  
DDMMYYYY 00.00 AM
NOTE: See the label in the paper tray, or the following illustration, to determine the X and Y
dimensions.
Y
X
ENWW Load paper and print media 105
 

Configure trays
The product automatically prompts you to configure a tray for type and size in the following situations:
●When you load paper into the tray
● When you specify a particular tray or media type for a print job through the printer driver or a
software program and the tray is not configured to match the print-job’s settings
The following message appears on the control panel:  Tray  [type] [size] To change size or type,
touch “Modify”. To accept, touch “OK” .
NOTE:The prompt does not appear if...