HP Color LaserJet CM3530fs MFP User Manual

5 Connectivity
●USB connection
●
Network configuration
ENWW 77
 

USB connection
This product supports a USB 2.0 connection. You must use an A-to-B type USB cable that is no longer
than 2 m (6.56 ft).
Network configuration
You might need to configure certain network parameters on the product. You can configure these
parameters from the control panel, the embedded Web server, or for most networks, from the HP Web
Jetadmin software.
For a complete list of supported networks and for instructions on configuring network parameters from
software, see the HP Jetdirect...

Service nameDescription
EWS (embedded Web server)Allows you to manage the product through a Web browser.
SNMP (Simple Network Management Protocol)Used by network applications for product management. SNMP
v1, SNMP v3, and standard MIB-II (Management Information
Base) objects are supported.
LLMNR (Link Local Multicast Name Resolution)Specifies if the product responds to LLMNR requests over IPv4
and IPv6.
TFTP ConfigurationAllows you to use TFTP to download a configuration file
containing additional...

Service nameDescription
benefits of encryption and authentication and allows for
multiple configurations.
Configure the network product
View or change network settings
You can use the embedded Web server to view or change IP configuration settings.
1.Print a configuration page, and locate the IP address.
●If you are using IPv4, the IP address contains only digits. It has this format:
xxx.xxx.xxx.xxx
● If you are using IPv6, the IP address is a hexadecimal combination of characters and digits.
It has a...

Manually configure IPv4 TCP/IP parameters from the control panel
In addition to using the embedded Web server, you can also use the control-panel menus to set an IPv4
address, subnet mask, and default gateway.
1.At the product control panel, touch the down arrow until the  Administration menu displays.
2. Touch the  Administration menu to open it.
3. Touch the down arrow until the  Initial Setup menu displays.
4. Touch the  Initial Setup menu to open it.
5. Touch the  Networking and I/O  menu to open...

Manually configure IPv6 TCP/IP parameters from the control panel
In addition to using the embedded Web server, you can also use the control-panel menus to set an IPv6
address.
1.At the product control panel, touch the down arrow until the  Administration menu displays.
2. Touch the Administration  menu to open it.
3. Touch the down arrow until the  Initial Setup menu displays.
4. Touch the Initial Setup  menu to open it.
5. Touch the Networking and I/O  menu to open it.
6. Touch the Embedded Jetdirect...

Disable network protocols (optional)
By factory default, all supported network protocols are enabled. Disabling unused protocols has the
following benefits:
●Decreases product-generated network traffic
● Prevents unauthorized users from printing to the product
● Provides only pertinent information on the configuration page
● Allows the product control panel to display protocol-specific error and warning messages
Disable IPX/SPX, AppleTalk, or DLC/LLC
NOTE: Do not disable IPX/SPX in Windows-based systems...

Link speed and duplex settings
The link speed and communication mode of the print server must match the network. For most situations,
leave the product in automatic mode. Incorrect changes to the link speed and duplex settings might
prevent the product from communicating with other network devices. If you need to make changes, use
the product control panel.
NOTE:Making changes to these settings causes the product to turn off and then on. Make changes
only when the product is idle.
1. At the product...

6 Paper and print media
●Understand paper and print media use
●
Supported paper and print media sizes
●
Custom paper sizes
●
Supported paper and print media types
●
Tray and bin capacity
●
Special paper or print media guidelines
●
Load paper and print media
●
Configure trays
●
Output locations
ENWW 85
 

Understand paper and print media use
This product supports a variety of paper and other print media in accordance with the guidelines in this
user guide. Paper or print media that does not meet these guidelines might cause the following problems:
●Poor print quality
● Increased jams
● Premature wear on the product, requiring repair
For best results, use only HP-brand paper and print media designed for laser printers or multiuse. Do
not use paper or print media made for inkjet printers. Hewlett-Packard...