HP Color LaserJet 3600dn User Manual

							Loading paper into tray 1
CAUTIONAvoid adding print media to tray 1 while th e printer is printing, or jams can occur.
1.Open tray 1.
NOTE If printing on special media, such as envelopes, use tray 1. See Printing envelopes
from tray 1  for more information.
2.Slide the output bin extension out from the bin.
3.Slide out the tray extender and, if necessa ry, open the additional tray extender.
ENWW Configuring trays 57
 
						

							4.Slide the width guides slightly  wider than the print media.
5.Place print media into the tray with the side to  be printed down, and the top, short edge in first.
NOTEIf you are printing on two sides, see Using 2-sided (duplex) printing  for loading
instructions.
6. Slide the paper width guides inwa rd until they lightly touch the print media stack on both sides
without bending it. Make sure that the media fits under the tabs on the width guides.
CAUTION Wait for the printer to finish printing before closing tray 1 (optional). Closing the
tray before the printer finishes can cause jams.
58 Chapter 4   Printing tasks ENWW
 
						

							Printing envelopes from tray 1
Many types of envelopes can be printed from tray 1. Up to 10 envelopes can be stacked in the tray.
Printing performance depends on  the construction of the envelope.
In the software, set margins at least 15 mm (0.6 in) from the edge of the envelope.
CAUTION Envelopes that contain clasps, snaps, windows, coated linings, exposed self-stick
adhesives, or other synthetic materials can severely damage the printer. To avoid jams and
possible printer damage, never try to print on both sides of an envelope. Before you load
envelopes, make sure that they are flat,  undamaged, and not stuck together. Do not use
envelopes that contain pressure-sensitive adhesive. To avoid jams, do not remove or insert
envelopes during printing.
To load envelopes into tray 1
1. Open tray 1.
2.Slide out the tray extender and, if necessa ry, open the additional tray extender.
ENWW Configuring trays 59
 
						

							3.Set the paper-width guides.
4.Load as many as 10 envelopes in the center of tr ay 1 with the side to be printed on facing down,
with the stamp area farthest fr om the printer, and the short edg e toward the printer. Slide the
envelopes into the printe r as far as they will go without forcing them.
5.Adjust the guides to touch the envelope stack wi thout bending the envelopes. Make sure that the
envelopes fit under the tabs on the guides.
Printing envelopes
1. If tray 1 is configured for a specif ic size, use the printer control panel to set the paper size for tray 1
to match the envelope size that you are printing.
2. Specify tray 1 in the software program.
60 Chapter 4   Printing tasks ENWW
 
						

							3.If your software does not automatically format an envelope, specify  Landscape for page orientation
in the software program. Use the guidelines in th e table that follows to set margins for return and
destination addresses on Commercial #10 or DL envelopes.
NOTE For envelopes of other sizes, adjust the margin settings appropriately.
4.Click  Print in the software program or printer driver.
Address typeLeft marginTop margin
Return15 mm (0.6 in)15 mm (0.6 in)
Destination 102 mm (4.0 in) 51 mm (2.0 in)
Printing from tray 2 and tray 3
Tray 2 holds up to 250 sheets of standard paper, while optional tray 3 holds up to 500 sheets of standard
paper. Tray 2 and tray 3 adjust for many sizes. Tray 3 is installed underneath tray 2. When tray 3 is
installed, the printer  detects it and lists tray 3 as  a choice in the control panel  CONFIGURE DEVICE
menu.
CAUTION The paper path for tray 3 passes through tray  2. If either tray 2 or tray 3 is partially
pulled out or removed, media from tray 3 cannot feed into the printer. This causes the printer to
jam.
Loading tray 2
CAUTION To avoid jams, never open or remove a tray during printing.
1.Pull tray 2 out of the printer and remove any media.
ENWW Configuring trays 61
 
						

							2.Slide the output bin extension out from the bin.
3.Adjust the length guide until the arrow points to the size that you are loading.
4.Move the side width guides until the arrow on t he right width guide points to the size that you are
loading.
62 Chapter 4   Printing tasks ENWW
 
						

							5.Load the media into the tray. If this is special paper such as letterhead, load it face-up with the top
edge toward the front of the tray.
NOTE If you are duplex printing, see Using 2-sided (duplex) printing  for loading
instructions.
6. Make sure that the stack of media is flat  and that the media is below the height tabs.
7.Slide the tray back into the printer.
ENWW Configuring trays 63
 
						

							Loading tray 3
1.Pull the tray out of the printer and remove any media.
2.Raise the output bin extension.
3.Adjust the length guide until the arrow points to the size that you are loading.
64 Chapter 4   Printing tasks ENWW
 
						

							4.Move the side width guides until the arrow on the ri ght width guide points to the size that you are
loading.
5. Load the media into the tray. If this is special paper , such as letterhead, load it face-up with the top
edge toward the front of the tray.
NOTE If you are duplex printing, see Using 2-sided (duplex) printing  for loading
instructions.
6. Make sure that the stack of media is  flat in the tray at all four corners, and keep it below the height
tabs.
ENWW Configuring trays 65
 
						

							7.Slide the tray back  into the printer.
66 Chapter 4   Printing tasks ENWW