Honeywell Galaxy 3 User Manual

Galaxy 3 Series Programming Manual
165
3 = Setting
The Setting attribute determines the function (if any) that the custom zone has in setting and unsetting the
system.
1. Begin Setif enabled, the custom zone starts the setting procedure,
2. Begin Entryif enabled, the custom zone starts the unsetting procedure,
3. Sets Systemif enabled, the custom terminates the setting procedure.
The default for each of the Setting attributes is disabled.  To enable the options, select the required Setting
attribute...

Galaxy 3 Series Programming Manual
166
Assemble Zone Example:
Assemble a zone that:
• activates Bells outputs when the system is set,
• activates Link-A outputs when the system is unset,
• generates an alarm condition when the system is part and full set,
• does not generate an alarm condition during the setting and unsetting procedure,
• acts as a terminator when the system is setting,
• logs all activation (in both set and unset states).
Programming:
(Assuming factory default settings)
 1.Select option...

Galaxy 3 Series Programming Manual
167
Option 65 – Timers
The Timer Control menu are as follows:
65 - Timers
Figure 13. Timer Control
Timers
1 = Timer A  
1 = Timer Status0 = Off
1 = On
2 = Timers (1-20)
Use A or B key to select timer - 20 times can be programmed,
then press ent.
[>], [), B(>) key to program day
# to toggle ON/OFF status
0-9 keys to enter time
to delete programming
2 = Timer B1 = Timer Status0 = Off
1 = On
2 = Timers (1-20)
Use A or B key to select timer - 20 times can be programmed,...

Galaxy 3 Series Programming Manual
168
Timer A and B
The Galaxy 3 Series control panels provide 2 timers that allow up to 20 times to be assigned over a 7 day
period; these can be combined in any order of On and Off times as required.
Programming Timers
 1.Enter the Timers option; 1=TIMER A is displayed. To modify or assign times go to Step 5.
 2.Press the ent key to select Timer A or the A then ent   keys to select Timer B; 1=TIMER STATUS is
displayed.
 3.Press the ent key; the status of the selected...

Galaxy 3 Series Programming Manual
169
Autoset
Each group can be programmed with 20 Autoset times over a 7 day period. These can be combined in any
order of On and Off times as required - for example 20 On times may be allocated to a group, or six Off
times and 14 On times.
When the system has been set by the Autoset function, outputs programmed as Autoset (refer to option 53 =
PROGRAM OUTPUTS) are activated; the Set outputs are also activated.
Programming Autoset
If groups are enabled (refer to option...

Galaxy 3 Series Programming Manual
170
There are five stages to programming the Autoset function:
1. Autoset Status
0 = Off (default)
1 = On
2 = Monitor - if selected, the setting and unsetting of the group is monitored:
• if not set manually before the On time, then the Set Late output is activated
• if  unset before the Off time, then the Unset Early output is activated.
2. Prewarning
1 = Period
0 – 50 minutes (default 30 minutes):
2 = Audible (this can be turned ON or OFF)
This option determines the...

Galaxy 3 Series Programming Manual
171
5. Autoset Events
This option programs the times when the selected group is automatically switched On (Autoset) and Off
(Autounset).
On selecting the option, the first 2 times assigned to the timer are displayed (the first time is on the top line, the
second is on the bottom). If no autoset times have been assigned, the keypad displays stars (7) on the top
line. Press the A key to step through each of the times until the required time is shown on the top line of...

Galaxy 3 Series Programming Manual
172
During the Lockout period, the group can not be unset unless an alarm has been activated in the group. In the
event of an alarm occurring during the Lockout period, any valid type 2.3 (or above) code assigned to the
group in alarm may be used to unset and/or reset the group. If multiple locked-out groups are in an alarm
condition entry of a single valid code (type 2.3 or above with access to the relevant groups) cancels the alarms
and unsets the activated groups....

Galaxy 3 Series Programming Manual
173
66 - Pre-Check
The Entry/Exit Horns beep once when each zone is tested. As each zone is successfully tested, the keypad
indicates the number that remain to be tested. When the last zone is successfully tested the Entry/Exit Horn
sounds twice and the keypad displays 0 CHECK ZONES; press the ent key to resume the system routine.
1 = Mode
The Mode determines the pre-check level that the selected zones are subjected to before the system can set.
The Mode is selected...

Galaxy 3 Series Programming Manual
174
Option 67 – Remote Reset
The Remote Reset option allows a user to perform an engineer reset authorized by the Alarm Receiving
Centre (ARC). In the event of an alarm that requires an engineer reset, the keypad displays a number, which,
when quoted to the ARC is decoded and exchanged for a new number. When this new number is entered it
resets the Galaxy panel.  Entering the engineer code also resets the Galaxy panel.
NOTE:The alarm conditions that require to be reset...