Honeywell Galaxy 2 User Manual

73
Galaxy 2 Series Installation Manual52 - Zones
Option 52 - Zones
Zones are programmed in menu 52. Each zone has a set of attributes as shown in the following table:
Selecting Zones
On entering the option, the first zone on the system is displayed; the zone address, function and group as-
signed are displayed on the top line, the descriptor is displayed on the bottom line.
From the display of the first zone, any zone on the system can be displayed by pressing the A or B keys or by
entering the address...

74
Galaxy 2 Series Installation Manual52 - Zones (cont’d)
1 = Function
This option allows the function of the zone to be selected. The zone can be assigned a different function for
each set mode (full, part and night set) to allow maximum flexibility. For instance, the zone can be pro-
grammed with the ‘Intruder’ function in Full and Part Set, but programmed as ‘Not Active’ in Night Set.
On selecting this option, the main zone function is selectable using the cursor keys, or by direct entry of the
code...

75
Galaxy 2 Series Installation Manual52 - Zones (cont’d)
2 = Descriptor
Each zone can be assigned with an alpha-numeric description of up to 16 characters (see Table 16, Zone
Text Characters). The descriptor is assembled from the character set in this table. On selecting the
Descriptor attribute, the currently assigned descriptor (blank by default) is displayed on the top line.  Each of
the keys on the keypad, when pressed, offers a choice of character on the bottom line. Press the key repeat-
edly to...

76
Galaxy 2 Series Installation Manual52 - Zones (cont’d)
6 = Groups
This option selects the group that a zone belongs to. The zone will always default to group 1, but can be set to
work under any group.
Zone Functions and Descriptions
00 Not Active
The zone is not active in alarms but tampers are monitored
01 Final
Zones programmed as Final initiate the unsetting procedure and terminate the setting procedure.
NOTE:The setting procedure can only terminate if  the Exit Time (Parameter 51.04) is set to...

77
Galaxy 2 Series Installation Manual52 - Zones (cont’d)
09 Keyswitch
The Keyswitch function allows a zone to be used as an on/off switch for the system or assigned groups.
Operating a Keyswitch zone when the system is unset starts the timed full setting routine, therefore the exit
time is applicable.  The system sets when the exit time expires or a Final or Push Set is activated.
If the system is set, operating a Keyswitch immediately unsets the assigned groups; there is no entry time
countdown.
The...

78
Galaxy 2 Series Installation Manual52 - Zones (cont’d)
20 Tamper
The Tamper function is continuously operational. When a Tamper zone is activated (1kΩ to 2kΩ), a tamper
alarm is generated; this requires to be reset by an authorised user code. If a tamper condition (open or short
circuit) occurs, a tamper alarm is also generated.
23 Batt Fail
This function is used to monitor the voltage of a back-up battery connected to a power supply. It causes an
Aux. Power Supply fault condition.
25 AC Fail
This...

79
Galaxy 2 Series Installation Manual
Option 53 - Outputs
This option allows the operation of all the system outputs to be programmed. Outputs numbered 0001 to
0008 are the outputs from the trigger header. Outputs numbered 1001 to 1004 are the standard outputs on
the main PCB. Outputs on expansion modules are shown if fitted. Each output has a sub menu containing
attributes as shown:
1. Function
Assigns the output function that activates the output.
2. Polarity
This selects if the output is normally off...

80
Galaxy 2 Series Installation Manual
04=Intruder (Latch)
The Intruder output is activated on a full alarm event during the set state.
05=Tamper (Latch)
The Tamper output is activated whenever a circuit tamper or lid tamper occurs. The output is not subject to
rearm: it latches on and remains active until a valid code, with the appropriate System Reset level, is entered.
06=24 Hour
The 24 Hour output is activated whenever a 24 Hour zone is activated. The output is not subject to rearm: it
latches on and...

81
Galaxy 2 Series Installation Manual
44=Abort (Pulse)
The Abort output is activated when a valid code is entered to unset the system following an intruder alarm.
The output stays on for one minute and then switches off.
45=Unset (Pulse)
The Unset output is activated each time the system (or group) is unset.
51=Link (Reflex)
Activates when link zone is activated see 52.1
66=RF Jam (Reflex)
The RF Jam output is activated whenever any of the RF RIO’s configured onto the system detect a significant
level...

82
Galaxy 2 Series Installation Manual
Option 56 - Comms
The Communications option is used to control the Galaxy 2 Series system signalling and has five submenus
broken down as follows:
1 = Telecoms; 5 = GSM; 6 = HW Priority; 7 = Parameters, 8 = 2-Way Voice
Telecom/GSM
These sub-sections set up the parameters for the built-in dialler modem and the GSM Module. Most of the
programming options are shared between both sections and can be modified from either one, except where
noted.
Figure 32. Telecom/GSM...